Elbow PP Comp, HDPE 110mmxfthd 4" O/ND-P (Product Code: SLE/WDF/14) is a 90° polypropylene adaptor elbow used to connect a 110 mm HDPE pipe to 4-inch threaded galvanised iron pipe while turning the line through a right angle. The HDPE end is a compression joint and the GI end has a female thread, with a rating of 10 bar at 20°C, which helps where a buried plastic main rises into a metal riser or pump connection. It is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India.

Specifications

What Is the 110 mm HDPE to 4-Inch GI Elbow Used For?

The change from plastic to metal pipe often happens exactly where the line changes direction — a buried HDPE main turning upward into a galvanised riser, or a horizontal HDPE run meeting a GI pipe that drops from a tank. The Elbow PP Comp, HDPE 110mmxfthd 4" O/ND-P handles both jobs in one fitting, so the installer avoids stacking a separate adaptor and a separate elbow at that point.

Make the GI joint first: seal the male thread of the 4" GI pipe with tape or jointing compound and screw it into the female end, taking care not to over-tighten into the polypropylene body. Then cut the HDPE pipe square, deburr it, insert it to full depth in the compression end and tighten the nut. Support the metal riser independently so its weight does not load the plastic elbow.

What to Specify When Ordering

• Pipe on each side: 110 mm OD HDPE and 4" ND GI with a male-threaded end.
• The number of risers or transition points that need an elbow.
• Operating conditions, to confirm they sit within 10 bar at 20°C and 0 to 50°C.

Supplier

Jain Scientific Equipments Private Limited trades as ScienceLab and supplies this elbow from Ambala, Haryana. It is a sourced fitting within the company's water, sanitation and hygiene range, quoted and dispatched together with the GI, PVC and HDPE items a project lists. The ScienceLab profile explains more about the company, which serves institutions in India and international markets.

Related Water, Sanitation & Hygiene Supplies

Fittings that sit on either side of an HDPE-to-GI change-over:

• Adaptor PP Comp, HDPE 110mmxmthd GI. 4"O/ND-P — a straight transition with a male GI thread when no turn is needed.
• Coupler PP Comp, HDPE 110mmxflng 4"O/ND-P — the flanged version for connecting to valves or pumps.
• Bend 90º equal fxf GI 4" ND 14 Bar — continues the GI side with a further turn in the same 4" size.
• Nipple Taper mthd Hex GI 14 Bar — a short male piece to join the elbow's female end directly to another female fitting; confirm the size.

Explore the Water, Sanitation & Hygiene Supplies category for more.

Frequently Asked Questions

What are the two ends of the Elbow PP Comp, HDPE 110mmxfthd 4" O/ND-P?
The Elbow PP Comp, HDPE 110mmxfthd 4" O/ND-P has a compression end for 110 mm outside-diameter HDPE pipe and a female-threaded end for 4-inch nominal diameter GI pipe. The two ends sit at 90° to each other.

What pressure and temperature can the elbow handle?
The Elbow PP Comp, HDPE 110mmxfthd 4" O/ND-P is rated for 10 bar at 20°C and suits a temperature range of 0 to 50°C. Where water or ambient temperatures run high, keep system pressure comfortably below the rated figure.

Why use this elbow instead of a straight adaptor and a GI elbow?
The Elbow PP Comp, HDPE 110mmxfthd 4" O/ND-P changes material and direction in a single fitting, which means one joint fewer, a shorter assembly and less weight hanging on the HDPE pipe than a straight adaptor combined with a separate GI elbow.

What is the elbow made from?
The Elbow PP Comp, HDPE 110mmxfthd 4" O/ND-P is made from reinforced, high-impact-strength polypropylene with UV stabilisation, giving a tough body that resists sunlight where the riser connection is above ground.

Who supplies the Elbow PP Comp, HDPE 110mmxfthd 4" O/ND-P?
Jain Scientific Equipments Pvt Ltd, trading as ScienceLab in Ambala, Haryana, supplies the Elbow PP Comp, HDPE 110mmxfthd 4" O/ND-P. The company sources it and quotes it for water-supply, institutional and project buyers in India and international markets.

How do I request a price for the elbow?
To price the Elbow PP Comp, HDPE 110mmxfthd 4" O/ND-P, send the quantity and delivery location through the contact page, or add it to the enquiry cart. Mention any matching GI or HDPE fittings so they can be quoted together.

Request a Quote

Add the Elbow PP Comp, HDPE 110mmxfthd 4" O/ND-P to the enquiry cart or write to us through the contact page. If the elbow is part of a larger institutional package, such as laboratory equipment tenders in India that include water works, list it on the same enquiry.

Last updated: 24 September 2026

T, PP comp, HDPE 110 x 110 x 110mm OD-P (Product Code: SLE/WDF/15) is an equal polypropylene compression tee used to split or join 110 mm HDPE water pipes at a full-size branch in distribution networks. All three ends are compression joints for pipe of 110 mm outside diameter, and the tee is rated for 10 bar at 20°C, so network crews can add a branch without fusion-welding equipment. It is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India.

Specifications

What Is the 110 mm HDPE Compression Tee Used For?

An equal tee is chosen when a branch needs the same capacity as the main — splitting a transmission line into two supply zones, feeding a second storage tank, or closing a loop so that water can reach an area from two directions. The T, PP comp, HDPE 110 x 110 x 110mm OD-P does this on 110 mm HDPE pipe using mechanical compression joints on every end.

Each joint is made by cutting the pipe square, chamfering and cleaning it, pushing it fully into the fitting and tightening the nut. Since no heat or power is needed, the tee suits field repairs and remote sites, and it can be reopened if the layout changes. Bed the tee on firm, even ground in the trench and backfill carefully around it so the branch pipe does not put bending strain on the fitting.

Supplier

ScienceLab is the trading name of Jain Scientific Equipments Private Limited, a laboratory equipment exporter from India based in Ambala, Haryana, whose supply range also covers water, sanitation and hygiene items. The company sources this HDPE compression tee and quotes it with matching couplers, adaptors and saddles, so a network project can be supplied as one package. Learn more on the ScienceLab profile page.

Related Water, Sanitation & Hygiene Supplies

HDPE fittings that are typically ordered with an equal tee:

• Coupler Reducing PP Comp, HDPE 110x90mm OD-P — reduces a branch from the tee to 90 mm pipe.
• Clamp Saddle PP, HDPE 110mm x fthd ½" O/ND-P — for small service tappings where a full-size tee is not required.
• Elbow PP Comp, HDPE 110mmxfthd 4" O/ND-P — turns a branch up into a 4" GI riser.
• Adaptor PP Comp, HDPE 110mmxmthd GI. 4"O/ND-P — connects a branch straight into 4" GI sockets.

The whole range is in the Water, Sanitation & Hygiene Supplies category.

Frequently Asked Questions

What size pipe does the T, PP comp, HDPE 110 x 110 x 110mm OD-P take?
The T, PP comp, HDPE 110 x 110 x 110mm OD-P takes HDPE pipe of 110 mm outside diameter on all three ends. It is an equal tee, so the branch carries the same pipe size as the run.

What is the pressure rating of the 110 mm HDPE tee?
The T, PP comp, HDPE 110 x 110 x 110mm OD-P is rated for 10 bar at 20°C, with a suitable temperature range of 0 to 50°C. In hot conditions allow a margin below the rated pressure, as plastic fittings generally lose capacity as temperature rises.

Does the tee need electrofusion or butt welding?
No. The T, PP comp, HDPE 110 x 110 x 110mm OD-P uses compression joints on each end, so the HDPE pipes are connected mechanically by inserting and tightening, without fusion-welding machines or power on site.

Can the tee be used for a smaller branch?
The T, PP comp, HDPE 110 x 110 x 110mm OD-P is equal on all ends. For a smaller branch, fit a reducing coupler on the branch outlet, or use a clamp saddle on the main where only a small service tapping is needed.

Who supplies the T, PP comp, HDPE 110 x 110 x 110mm OD-P?
Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, Haryana, supplies the T, PP comp, HDPE 110 x 110 x 110mm OD-P. The company sources the tee for water networks, institutions and project buyers in India and international markets.

What information does a quotation for the tee need?
A quotation for the T, PP comp, HDPE 110 x 110 x 110mm OD-P needs the quantity, the delivery location and any other HDPE fittings you plan to use. Send these through the contact page so all items can be priced together.

Request a Quote

Use the contact page to send quantities of the T, PP comp, HDPE 110 x 110 x 110mm OD-P and the rest of your HDPE fitting list, or add the tee to the enquiry cart. Network buyers often combine tees, couplers and saddles in a single request.

Last updated: 24 September 2026

Adaptor PP Comp, HDPE 110mmxmthd GI. 4"O/ND-P (Product Code: SLE/WDF/16) is a straight polypropylene adaptor used to connect a 110 mm HDPE water pipe into a 4-inch female-threaded GI socket, valve or fitting. One end is a compression joint for the HDPE pipe and the other carries an external (male) thread, with a rating of 10 bar at 20°C, which makes it a simple in-line link between plastic mains and threaded metal hardware. It is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India.

Specifications

What Is the HDPE to Male GI Thread Adaptor Used For?

HDPE pipe cannot be threaded, so wherever a plastic main has to enter threaded metal hardware an adaptor is needed. The Adaptor PP Comp, HDPE 110mmxmthd GI. 4"O/ND-P screws its male thread into a 4" female GI socket — for example a socket on a steel riser, the female end of a GI cross, bend or elbow, or a threaded valve body — and accepts the 110 mm HDPE pipe in its compression end.

Wrap the male thread with sealing tape and screw it into the metal socket firmly but without excessive force, since a plastic thread can be damaged by over-tightening. Then prepare the HDPE end with a square cut, chamfer and clean, and tighten it into the compression side. Where the adaptor enters heavy metal pipework, support the metal side so that the plastic body does not take bending loads.

What to Specify When Ordering

• The 4" female GI fitting or valve the adaptor will screw into.
• The number of HDPE-to-GI transitions on the layout.
• Operating pressure and temperature, to confirm they stay within 10 bar at 20°C and 0 to 50°C.

Supplier

Jain Scientific Equipments Private Limited, trading as ScienceLab from Ambala, Haryana, supplies this compression adaptor as part of its water, sanitation and hygiene range. The company, whose core business includes lab equipment export from India, sources plumbing items like this for institutions and project buyers and handles the quotation, packing and dispatch. See the company profile for details.

Related Water, Sanitation & Hygiene Supplies

Fittings on the metal and plastic sides of this adaptor:

• Cross equal fthd GI 4" ND 14 Bar — a 4" female-threaded junction the adaptor can screw into.
• Elbow 90º equal fthd GI ND 14 Bar — another 4" female fitting that can receive the adaptor at a turn.
• Coupler PP Comp, HDPE 110mmxflng 4"O/ND-P — the choice for flanged rather than threaded connections.
• T, PP comp, HDPE 110 x 110 x 110mm OD-P — branches the HDPE main before the transition.

More items are in the Water, Sanitation & Hygiene Supplies category.

Frequently Asked Questions

Which ends does the Adaptor PP Comp, HDPE 110mmxmthd GI. 4"O/ND-P have?
The Adaptor PP Comp, HDPE 110mmxmthd GI. 4"O/ND-P has a compression end for 110 mm outside-diameter HDPE pipe and an external (male) thread for 4-inch nominal diameter GI pipe sockets. It is a straight fitting with no change of direction.

What does the male thread connect to?
The male thread of the Adaptor PP Comp, HDPE 110mmxmthd GI. 4"O/ND-P screws into a 4-inch female-threaded GI socket, fitting or threaded valve. Where the GI pipe presents a male end instead, a female-threaded transition fitting is needed.

What pressure and temperature is the adaptor rated for?
The Adaptor PP Comp, HDPE 110mmxmthd GI. 4"O/ND-P is rated for 10 bar at 20°C and a temperature range of 0 to 50°C. Keep pump and test pressures within this rating and allow extra margin in warm conditions.

What is the adaptor made of?
The Adaptor PP Comp, HDPE 110mmxmthd GI. 4"O/ND-P is reinforced, high-impact-strength polypropylene with UV stabilisation, so the body is tough and tolerates sunlight at above-ground connections such as pump outlets and tank risers.

Who supplies the Adaptor PP Comp, HDPE 110mmxmthd GI. 4"O/ND-P?
The Adaptor PP Comp, HDPE 110mmxmthd GI. 4"O/ND-P is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, Haryana. The company sources it and quotes it for water-supply projects and institutions in India and international markets.

Can I order the adaptor together with GI fittings?
Yes, the Adaptor PP Comp, HDPE 110mmxmthd GI. 4"O/ND-P can be quoted together with the 4" GI fittings it connects to. List every item with its quantity on the contact page or in the enquiry cart for one combined quotation.

Request a Quote

Tell us how many HDPE-to-GI transitions your layout has and what each adaptor screws into, then send those details for the Adaptor PP Comp, HDPE 110mmxmthd GI. 4"O/ND-P through the contact page. You can also add it to the enquiry cart while you select the other fittings.

Last updated: 24 September 2026

Coupler Reducing PP Comp, HDPE 110x90mm OD-P (Product Code: SLE/WDF/17) is a straight polypropylene reducing coupler used to join a 110 mm HDPE pipe to a 90 mm HDPE pipe in water supply mains. Both ends are female compression joints, one for each outside diameter, and the coupler is rated for 10 bar at 20°C, letting network installers step the pipe size down without welding. It is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India.

Specifications

What Is the 110 x 90 mm HDPE Reducing Coupler Used For?

Water networks are commonly laid in stepped sizes: the pipe nearest the source carries the whole flow, and diameters reduce further out as fewer connections remain. The Coupler Reducing PP Comp, HDPE 110x90mm OD-P marks that step between 110 mm and 90 mm HDPE pipe. It is equally useful on repair and extension jobs, where a new 110 mm line has to meet an existing 90 mm pipe.

Install the reducer in line with both pipes, each cut square, chamfered and pushed fully home before its compression nut is tightened. Water moves faster through the smaller pipe for the same flow, so place the joint in a straight, well-supported section of trench and bed it evenly. Record the location on the as-built drawing so maintenance teams know where the size changes.

What to Specify When Ordering

• Both pipe sizes: 110 mm and 90 mm outside diameter HDPE.
• The number of size changes on the network, one coupler for each.
• Pressure and temperature conditions, which should stay within 10 bar at 20°C and 0 to 50°C.

Supplier

Jain Scientific Equipments Private Limited, trading as ScienceLab in Ambala, Haryana, supplies this reducing coupler as a sourced item within its water, sanitation and hygiene range. For institutions procuring through laboratory equipment tenders in India or other vendor-registered channels, the supplying company's details are CIN U29309HR2020PTC087597 and GSTIN 06AAECJ8618A1ZT. The company profile gives more background.

Related Water, Sanitation & Hygiene Supplies

Fittings used alongside a reducer on HDPE and PVC networks:

• T, PP comp, HDPE 110 x 110 x 110mm OD-P — a full-size branch on the 110 mm main before the reduction.
• Clamp Saddle PP, HDPE 110mm x fthd ½" O/ND-P — for service tappings along the 110 mm section.
• Coupler PP Comp, HDPE 110mmxflng 4"O/ND-P — connects the 110 mm line to flanged valves or pumps.
• Reducing Coupler PVC skt scj 110x90mm-P — the solvent-cement equivalent for uPVC pipe networks.

The full selection is in the Water, Sanitation & Hygiene Supplies category.

Frequently Asked Questions

Which pipe sizes does the Coupler Reducing PP Comp, HDPE 110x90mm OD-P join?
The Coupler Reducing PP Comp, HDPE 110x90mm OD-P joins HDPE pipe of 110 mm outside diameter to HDPE pipe of 90 mm outside diameter. Both ends are female compression joints, so nothing needs to be threaded or welded.

What is the pressure rating of the reducing coupler?
The Coupler Reducing PP Comp, HDPE 110x90mm OD-P is rated for 10 bar at 20°C, with a suitable temperature range of 0 to 50°C. Design working and test pressures to stay within this rating, particularly where the water temperature is high.

Can the coupler join HDPE to PVC pipe?
The Coupler Reducing PP Comp, HDPE 110x90mm OD-P is specified for HDPE pipes. For uPVC networks, see the solvent-cement reducing coupler in the same sizes in our WASH range, and ask us about transitions between the two materials.

Can the reducing coupler be dismantled later?
Compression joints like those on the Coupler Reducing PP Comp, HDPE 110x90mm OD-P can generally be opened by loosening the nuts, which helps during repairs or layout changes. Inspect the pipe ends and sealing surfaces carefully before reassembly.

Who supplies the Coupler Reducing PP Comp, HDPE 110x90mm OD-P?
Jain Scientific Equipments Pvt Ltd (ScienceLab) of Ambala, Haryana, supplies the Coupler Reducing PP Comp, HDPE 110x90mm OD-P. The company sources it for water-network, institutional and project buyers in India and international markets, quoting it with related HDPE fittings.

What should I send to get a quotation?
Send the quantity of the Coupler Reducing PP Comp, HDPE 110x90mm OD-P, the delivery location and any other HDPE or GI fittings you need through the contact page. A consolidated quotation is then prepared for the complete list.

Request a Quote

Enquire about the Coupler Reducing PP Comp, HDPE 110x90mm OD-P on the contact page, or place it in the enquiry cart with the tees, saddles and adaptors on your pipe schedule. Include the number of size changes in your network so quantities match the layout.

Last updated: 24 September 2026

Dewatering Pump, 11-22 cbm/hr@50m TMH (Product Code: SLE/WDF/18) is an air-powered diaphragm dewatering unit used to keep hand-dug wells free of water while they are being dug and deepened. It delivers up to 22 m³/hr, or 11 m³/hr against a 50 m total manometric head, and it is self-priming, can run dry and handles water with relatively high solid content, which suits well-digging teams and WASH contractors. It is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India.

Specifications

What Is the Dewatering Pump Used For?

Digging a well by hand means working below the water table, where water keeps seeping into the shaft. The Dewatering Pump, 11-22 cbm/hr@50m TMH removes that inflow so the crew can keep excavating and lining the well. Its diaphragm design copes with muddy, sandy water that can quickly wear other pump types, and because it can run dry, it is not harmed when the shaft is pumped empty between inflows.

The pump is driven by compressed air rather than an electric motor. A diesel engine on the two-wheeled trolley drives the air compressor at the surface, so no mains power connection is needed at the well. Fill the fuel tank before a shift, since it holds enough for 12 hours of continuous normal operation, check the oil-bath air filter often in dusty conditions, and keep the compressor's pressure safety valve in working order.

What to Specify When Ordering

• The expected depth and head at your well sites, compared with the listed 11 m³/hr at 50 m TMH.
• The number of units required for the programme.
• Any accessories or spares you would like quoted — ask us what can be included.
• The delivery location and site access for a trolley-mounted unit.

Supplier

This pump is a sourced unit supplied by ScienceLab, the trading name of Jain Scientific Equipments Private Limited, Ambala, Haryana. Recognised by schools and colleges as a laboratory equipment supplier in India, the company also supplies pumps and fittings for water, sanitation and hygiene work and can quote the dewatering unit with the other items a well-construction programme needs. See the ScienceLab profile for more about the company.

Related Water, Sanitation & Hygiene Supplies

Pumps and hand pumps used before and after a well is completed:

• Pump Centrifugal, Diesel 50cbm/hr — a diesel-driven centrifugal pump listed for larger transfer duties.
• Pump Electric sbmr bh 18cbm/hr — an electric pump option for permanent supply once a water source is in service.
• Handpump Variant 3 Norm — a hand pump for fitting on a completed well.
• Handpump DA 9-15m Variant — a direct-action hand pump variant for shallower wells.

Browse the Water, Sanitation & Hygiene Supplies category for the full range.

Frequently Asked Questions

What flow does the Dewatering Pump, 11-22 cbm/hr@50m TMH deliver?
The Dewatering Pump, 11-22 cbm/hr@50m TMH has a listed maximum capacity of 22 m³ per hour and delivers 11 m³ per hour against a total manometric head of 50 m. Actual output on site depends on the head and conditions at each well.

What powers the dewatering pump?
The Dewatering Pump, 11-22 cbm/hr@50m TMH is an air-powered diaphragm pump. Its air comes from a compressor mounted on a two-wheeled trolley, working at 7 bar with a pressure safety valve and directly flange-coupled to an air-cooled, direct-injection diesel engine.

Can the pump handle muddy water or run dry?
Yes. The Dewatering Pump, 11-22 cbm/hr@50m TMH is self-priming, can run dry and can handle water with relatively high solid content, which suits the silty inflow that is common during hand-dug well excavation.

How long can the engine run on one tank of fuel?
The engine of the Dewatering Pump, 11-22 cbm/hr@50m TMH has a fuel tank sized for 12 hours of continuous normal operation. It also has an oil-bath air filter, a soundproof muffler, a speed governor and rope or recoil starting.

Who supplies the Dewatering Pump, 11-22 cbm/hr@50m TMH?
Jain Scientific Equipments Pvt Ltd, trading as ScienceLab in Ambala, Haryana, supplies the Dewatering Pump, 11-22 cbm/hr@50m TMH. The company sources the unit and quotes it for well-construction, WASH and institutional projects in India and international markets.

What should a quotation request for the pump include?
A quotation request for the Dewatering Pump, 11-22 cbm/hr@50m TMH should state the number of units, the delivery location and the expected well depth. Questions about spares, documentation or accessories can be raised on the contact page so we can confirm what is available.

Request a Quote

Send your requirement for the Dewatering Pump, 11-22 cbm/hr@50m TMH through the contact page, including the number of well sites and the delivery destination, or add the unit to the enquiry cart together with any hand pumps or fittings for the completed wells.

Last updated: 24 September 2026

Coupler PVC Socket Solvent Cement Joint Flange, 110mm x 4" (Product Code: SLE/WDF/19) is a uPVC flanged coupler with collar used to connect 110 mm PVC water pipe to 4-inch flanged pipes, valves or fittings. The pipe end is joined by solvent cement in a socket, the other end is a flange, and the coupler is rated for 10 bar at 20°C, which suits PVC network installers who need a removable connection at pumps and valve chambers. It is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India.

Specifications

What Is the 110 mm uPVC Flanged Coupler Used For?

uPVC pipe is joined permanently with solvent cement, which is ideal along a buried line but inconvenient wherever equipment may have to be removed. The Coupler PVC Socket Solvent Cement Joint Flange, 110mm x 4" gives the line a flanged end at those points — a pump delivery, a flow meter, a sluice valve or a steel pipe section — so the equipment can later be unbolted without cutting the PVC.

For the solvent joint, cut the 110 mm pipe square, remove burrs, clean both surfaces, apply a cement suitable for uPVC to pipe and socket, and push home with a slight twist. Hold the joint briefly and let it cure for the time the cement's instructions give before pressure testing. On the flange side, align the bolt holes, fit a suitable gasket and tighten the bolts evenly in a cross pattern so the uPVC flange seats without stress.

What to Specify When Ordering

• The drilling pattern of the mating 4" flange, so compatibility can be checked.
• Whether solvent cement, a gasket or bolts should be quoted with the coupler — ask us what can be included.
• The quantity, one for each flanged connection on the PVC line.

Supplier

ScienceLab, the trading name of Jain Scientific Equipments Private Limited in Ambala, Haryana, supplies this uPVC flanged coupler from its water, sanitation and hygiene range. Many buyers first know the company as a laboratory equipment exporter from India; for pipeline projects it sources fittings such as this one and combines them in a single quotation with pumps, HDPE fittings and GI items. Details are on the ScienceLab company profile.

Related Water, Sanitation & Hygiene Supplies

Other fittings for 110 mm PVC and HDPE lines:

• Coupler PP Comp, HDPE 110mmxflng 4"O/ND-P — the flanged coupler equivalent for HDPE pipe.
• Union Equal PVC, fxf, scj 10Bar 110mm OD-P — a dismantling joint within a solvent-cement PVC line.
• Reducing Coupler PVC skt scj 110x90mm-P — steps the uPVC line down to 90 mm.
• Tee Adaptor fxf, scj, PVC 110mm x 4" fthd O/ND-P — a PVC tee with a 4" threaded branch.

See the complete Water, Sanitation & Hygiene Supplies category.

Frequently Asked Questions

What does the Coupler PVC Socket Solvent Cement Joint Flange, 110mm x 4" connect?
The Coupler PVC Socket Solvent Cement Joint Flange, 110mm x 4" connects 110 mm outside-diameter PVC pipe to 4-inch nominal diameter flanged pipes or fittings. The PVC pipe is solvent-cemented into its socket, while the flanged end bolts to the mating flange.

What material is the flanged coupler made of?
The Coupler PVC Socket Solvent Cement Joint Flange, 110mm x 4" is made of uPVC, unplasticised polyvinyl chloride, the rigid form of PVC used for pressure water pipe. It is intended for solvent-cement jointing with PVC pipes.

What pressure and temperature rating does the coupler have?
The Coupler PVC Socket Solvent Cement Joint Flange, 110mm x 4" is rated for 10 bar at 20°C, with a suitable temperature range of 0 to 50°C. Allow extra margin where water temperatures are high, as PVC generally loses pressure capacity with heat.

Can the coupler be removed once installed?
The solvent-cement side of the Coupler PVC Socket Solvent Cement Joint Flange, 110mm x 4" is a permanent joint, but the flanged side can be unbolted, so the connected valve, pump or pipe section can be removed without cutting the PVC line.

Who supplies the Coupler PVC Socket Solvent Cement Joint Flange, 110mm x 4"?
Jain Scientific Equipments Pvt Ltd, trading as ScienceLab in Ambala, Haryana, supplies the Coupler PVC Socket Solvent Cement Joint Flange, 110mm x 4". It sources the fitting for water-network, institutional and project buyers in India and international markets.

What should an enquiry for the coupler include?
An enquiry for the Coupler PVC Socket Solvent Cement Joint Flange, 110mm x 4" should include the quantity, delivery location, flange details and any other PVC fittings needed. Send it through the contact page so everything can be quoted together.

Request a Quote

Quote requests for the Coupler PVC Socket Solvent Cement Joint Flange, 110mm x 4" can be sent through the contact page; mention your flange details and the quantity. Alternatively, add it to the enquiry cart along with the unions, reducers and tees on your PVC pipe schedule.

Last updated: 24 September 2026

Cap, female PVC, scj, 110mm OD-P (Product Code: SLE/WDF/20) is a uPVC end cap used to seal the open end of a 110 mm outside-diameter PVC pipe in pressurised water-supply lines. Contractors, WASH programmes and campus maintenance teams fit it wherever a run must stop, for example during a school lab renovation or a new water main; its female socket is solvent-cemented over the pipe and it is rated 10 bar at 20°C. It is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India.

Specifications

What Is the 110mm PVC End Cap Used For?

An end cap is the full stop of a pipeline. On a 110 mm uPVC main it closes the far end of a distribution line, blanks off a stub left for a later connection, or seals a finished section so it can be filled and checked before the rest of the network is joined. Because the socket is solvent-welded, the closure is permanent: to extend the line later, the pipe is cut behind the cap and a new fitting is cemented on.

For a sound joint, cut the pipe square, remove burrs, clean both surfaces, apply solvent cement to the pipe end and the socket, push the cap fully home and hold it briefly. Let the joint cure as the cement maker directs before pressurising, and keep the working pressure within the 10 bar at 20°C rating, remembering that PVC carries less pressure as water temperature rises towards the 50°C limit.

What to Specify When Ordering

• Pipe size: this cap suits pipe of 110 mm outside diameter only.
• Joint system: confirm your pipe is solvent-cement uPVC, not a rubber-ring or HDPE compression line.
• Quantity: one cap for every dead end or reserved stub on the drawing.
• Companion fittings: list any 110 mm couplers, tees or unions needed in the same order.

Supplier

Jain Scientific Equipments Private Limited trades as ScienceLab and supplies this 110 mm uPVC end cap from Ambala, Haryana. Alongside its laboratory ranges, the company sources water-supply fittings so that schools, NGOs, contractors and importers can place one consolidated order with a single laboratory equipment supplier in India. Company background is on the ScienceLab profile page.

Related Water, Sanitation & Hygiene Supplies

These fittings from the same 110 mm uPVC series are often ordered with the end cap:

• Coupler Straight/Equal PVC, skt, scj, 110mm-P — joins two pipe lengths on the run leading to the capped end.
• Union Equal PVC, fxf, scj 10Bar 110mm OD-P — fitted upstream of the cap when the line may need to be opened later.
• Reducing Tee, PVC, fxf, scj, 10Bar, 110x90mm OD-P — takes a 90 mm branch off the same main before it ends.
• Tee Adaptor fxf, scj, PVC 110mm x 4" fthd O/ND-P — branches the 110 mm line to threaded G.I. pipework.

See the full range of pipe fittings, pumps and hygiene items in Water, Sanitation & Hygiene Supplies.

Frequently Asked Questions

What pipe size does the Cap, female PVC, scj, 110mm OD-P fit?
The Cap, female PVC, scj, 110mm OD-P fits PVC pipe with a 110 mm outside diameter. Its female socket slides over the pipe end and is fixed with solvent cement, so the pipe OD must match exactly; for other sizes, ask us through the contact page.

What pressure and temperature is the 110mm PVC end cap rated for?
The 110mm PVC end cap (Cap, female PVC, scj, 110mm OD-P) is rated 10 bar at 20°C and suits water between 0 and 50°C. Allowable pressure is lower at warmer temperatures, so the system designer should confirm the working pressure for the actual water temperature.

Can the 110mm PVC end cap be removed and reused?
No. The 110mm PVC end cap is solvent-welded, so the joint is permanent. To extend the line, cut the pipe behind the cap and cement on a new fitting such as a straight coupler; if reopening is expected, fit a union upstream instead.

Can the Cap, female PVC, scj, 110mm OD-P be used on drinking-water lines?
Drinking-water suitability of the Cap, female PVC, scj, 110mm OD-P should be confirmed with us for your application before you order. Describe the line and what it will carry through the contact page, and ask what information is available for the batch you are quoted.

Who supplies the Cap, female PVC, scj, 110mm OD-P?
Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, Haryana, supplies the Cap, female PVC, scj, 110mm OD-P, sourcing it for schools, WASH projects, contractors and dealers in India and international markets together with its laboratory and hygiene ranges.

What should a quotation request for the 110mm PVC cap include?
A quotation request for the 110mm PVC cap should give the product code SLE/WDF/20, the quantity, the delivery location and any other 110 mm fittings needed, so ScienceLab can price the whole pipe order in one reply.

Request a Quote

Send your quantity and delivery details through the ScienceLab contact page, or add this cap to the enquiry cart with the other fittings you need and request one combined quotation.

Last updated: 24 September 2026

Elbow 90º, PVC scj/fthd, 40mm x 1¼"-P (Product Code: SLE/WDF/21) is a 90° transition elbow used to connect a 40 mm outside-diameter PVC pipe to a 1¼" nominal-diameter galvanised iron (G.I.) pipe in water-supply installations. Plumbers and project teams use it where a plastic line turns a corner and changes to metal in one fitting: one end is a solvent-cement socket, the other a female thread. It is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India.

Specifications

What Is the 40mm PVC to GI Elbow Used For?

Mixed PVC and G.I. pipework is common where a buried plastic line rises to a metal riser, a stand post or a threaded valve. This elbow handles both jobs at once: it turns the flow through 90° and converts the 40 mm solvent-weld PVC pipe to a 1¼" threaded G.I. connection, saving a separate bend and adaptor and one extra joint.

Many installers make the threaded connection first and cement the PVC side afterwards, so turning the elbow on the thread does not disturb a fresh solvent joint. Seal the male G.I. thread with PTFE tape rather than a paste that may not suit PVC, and tighten by hand plus a modest turn, because over-tightening can split a plastic female thread. Keep service within 10 bar at 20°C and the 0 to 50°C range.

What to Specify When Ordering

• PVC side: 40 mm outside diameter, solvent-cement pipe.
• G.I. side: 1¼" nominal diameter pipe with a male thread to enter the female end.
• Quantity: count each point where the line both turns and changes material.
• Other sizes: if your PVC or G.I. sizes differ, ask us before ordering.

Supplier

ScienceLab is the trading name of Jain Scientific Equipments Private Limited, which supplies this PVC-to-G.I. elbow from Ambala, Haryana, together with a wider set of water-supply and sanitation items for institutions and project buyers. For vendor registration, the supplying company's Importer-Exporter Code is AAECJ8618A (DGFT) and its GSTIN is 06AAECJ8618A1ZT. Read more on the company profile.

Related Water, Sanitation & Hygiene Supplies

Fittings that sit on either side of a PVC-to-G.I. change of direction:

• Elbow 90º equal fthd GI ND 14 Bar — an all-G.I. bend for runs that stay in metal.
• Elbow Equal PVC fxf, Solvent Cement Joint, 32mm OD-P — an all-PVC elbow for smaller solvent-weld branches.
• Adaptor fxm, scj, PVC 110mm x GI.4" O/ND-P — a straight PVC-to-G.I. transition for 110 mm mains.
• Cap fthd GI 14 Bar — closes a male-threaded G.I. end during staged work.

Browse all pipe fittings and hygiene products in Water, Sanitation & Hygiene Supplies.

Frequently Asked Questions

Which pipes does the Elbow 90º, PVC scj/fthd, 40mm x 1¼"-P connect?
The Elbow 90º, PVC scj/fthd, 40mm x 1¼"-P connects a PVC pipe of 40 mm outside diameter, cemented into its socket, to a G.I. pipe of 1¼" nominal diameter, screwed into its female thread, while turning the line through 90°.

What is the pressure rating of the 40mm x 1¼" PVC elbow?
The 40mm x 1¼" PVC elbow (Elbow 90º, PVC scj/fthd, 40mm x 1¼"-P) is rated 10 bar at 20°C and suits water from 0 to 50°C. Warmer water reduces the pressure a PVC fitting can safely carry, so design for the actual service temperature.

How should the threaded end of the 40mm PVC to GI elbow be sealed?
Seal the male G.I. thread entering the 40mm PVC to GI elbow with PTFE tape and avoid heavy wrenching, since over-tightening can crack a plastic female thread. Choose any thread compound only if its maker states it is compatible with PVC.

Is the Elbow 90º, PVC scj/fthd, 40mm x 1¼"-P suitable for drinking water?
Please check with us before using the Elbow 90º, PVC scj/fthd, 40mm x 1¼"-P on a drinking-water line. Tell us the application and the water source through the contact page, and ScienceLab will reply with what it can confirm for the supplied batch.

Who supplies the 40mm x 1¼" PVC to GI elbow?
Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, Haryana, supplies the 40mm x 1¼" PVC to GI elbow to schools, WASH programmes, contractors and dealers across India and international markets, alongside its laboratory equipment and hygiene ranges.

Request a Quote

Tell us the quantity of product code SLE/WDF/21 and your delivery location through the contact page, or place it in the enquiry cart with the rest of your PVC and G.I. fittings for a single quotation.

Last updated: 24 September 2026