- Physics Lab Equipment
- Chemistry Lab Equipment
- Biology Lab Equipment
- Anatomical Lab Equipment
- Learning
- Educational Lab Equipment
- Magnets
- Agriculture
- Astronomy
- Earth Science
- Geography Lab Equipment
- Safety Lab Coat
- Laboratory
- Meteorological
- Electricity & Magnetism
- Heat
- School Lab Equipment
- Lab Glassware
- Science Lab Equipment
- Tvet Lab Equipment
- Robotics Kits Supplier and Manufacturer for Schools India
- Math Lab Equipment Manufacturers and Exporters in Ambala
- STEM Kits Manufacturers and Supplier India
- Engineering Lab Equipment
- Hospital Lab Equipment
- Water, Sanitation & Hygiene Supplies
- Cold Chain, Solar & Communication Equipment
- Nutrition
T, PP comp, HDPE 110 x 110 x 110mm OD-P
T, PP comp, HDPE 110 x 110 x 110mm OD-P (Product Code: SLE/WDF/15) is an equal polypropylene compression tee used to split or join 110 mm HDPE water pipes at a full-size branch in distribution networks. All three ends are compression joints for pipe of 110 mm outside diameter, and the tee is rated for 10 bar at 20°C, so network crews can add a branch without fusion-welding equipment. It is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India.
Specifications
| Parameter | Detail |
|---|---|
| Fitting type | Equal tee, compression fitting on all three ends |
| Pipe outside diameter | 110 mm on each end (110 x 110 x 110 mm) |
| For use with | HDPE pipes |
| Material | Reinforced, high-impact-strength polypropylene, UV stabilised |
| Pressure rating | 10 bar at 20°C |
| Temperature range | 0 to 50°C |
| Product code | SLE/WDF/15 |
| Supplied by | Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India |
What Is the 110 mm HDPE Compression Tee Used For?
An equal tee is chosen when a branch needs the same capacity as the main — splitting a transmission line into two supply zones, feeding a second storage tank, or closing a loop so that water can reach an area from two directions. The T, PP comp, HDPE 110 x 110 x 110mm OD-P does this on 110 mm HDPE pipe using mechanical compression joints on every end.
Each joint is made by cutting the pipe square, chamfering and cleaning it, pushing it fully into the fitting and tightening the nut. Since no heat or power is needed, the tee suits field repairs and remote sites, and it can be reopened if the layout changes. Bed the tee on firm, even ground in the trench and backfill carefully around it so the branch pipe does not put bending strain on the fitting.
Supplier
ScienceLab is the trading name of Jain Scientific Equipments Private Limited, a laboratory equipment exporter from India based in Ambala, Haryana, whose supply range also covers water, sanitation and hygiene items. The company sources this HDPE compression tee and quotes it with matching couplers, adaptors and saddles, so a network project can be supplied as one package. Learn more on the ScienceLab profile page.
Related Water, Sanitation & Hygiene Supplies
HDPE fittings that are typically ordered with an equal tee:
- Coupler Reducing PP Comp, HDPE 110x90mm OD-P — reduces a branch from the tee to 90 mm pipe.
- Clamp Saddle PP, HDPE 110mm x fthd ½" O/ND-P — for small service tappings where a full-size tee is not required.
- Elbow PP Comp, HDPE 110mmxfthd 4" O/ND-P — turns a branch up into a 4" GI riser.
- Adaptor PP Comp, HDPE 110mmxmthd GI. 4"O/ND-P — connects a branch straight into 4" GI sockets.
The whole range is in the Water, Sanitation & Hygiene Supplies category.
Frequently Asked Questions
What size pipe does the T, PP comp, HDPE 110 x 110 x 110mm OD-P take?
The T, PP comp, HDPE 110 x 110 x 110mm OD-P takes HDPE pipe of 110 mm outside diameter on all three ends. It is an equal tee, so the branch carries the same pipe size as the run.
What is the pressure rating of the 110 mm HDPE tee?
The T, PP comp, HDPE 110 x 110 x 110mm OD-P is rated for 10 bar at 20°C, with a suitable temperature range of 0 to 50°C. In hot conditions allow a margin below the rated pressure, as plastic fittings generally lose capacity as temperature rises.
Does the tee need electrofusion or butt welding?
No. The T, PP comp, HDPE 110 x 110 x 110mm OD-P uses compression joints on each end, so the HDPE pipes are connected mechanically by inserting and tightening, without fusion-welding machines or power on site.
Can the tee be used for a smaller branch?
The T, PP comp, HDPE 110 x 110 x 110mm OD-P is equal on all ends. For a smaller branch, fit a reducing coupler on the branch outlet, or use a clamp saddle on the main where only a small service tapping is needed.
Who supplies the T, PP comp, HDPE 110 x 110 x 110mm OD-P?
Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, Haryana, supplies the T, PP comp, HDPE 110 x 110 x 110mm OD-P. The company sources the tee for water networks, institutions and project buyers in India and international markets.
What information does a quotation for the tee need?
A quotation for the T, PP comp, HDPE 110 x 110 x 110mm OD-P needs the quantity, the delivery location and any other HDPE fittings you plan to use. Send these through the contact page so all items can be priced together.
Request a Quote
Use the contact page to send quantities of the T, PP comp, HDPE 110 x 110 x 110mm OD-P and the rest of your HDPE fitting list, or add the tee to the enquiry cart. Network buyers often combine tees, couplers and saddles in a single request.
Last updated: 24 September 2026
