Bend 90º equal fxf GI 4" ND 14 Bar (Product Code: SLE/WDF/06) is a right-angle galvanised iron pipe bend used to turn a 4-inch threaded water line through 90° in pressurised supply and distribution systems. Both ends are female-threaded (fxf) to the same 4" nominal diameter, so site crews can route mains around corners, walls and tank connections without a change of size. It is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India, together with related water-supply fittings.

Specifications

What Is the 4-Inch GI 90° Bend Used For?

Pipe routes rarely run straight from source to outlet. The Bend 90º equal fxf GI 4" ND 14 Bar lets a 4-inch galvanised main turn a corner — up a wall from a pump, across to an overhead tank or around a building footing — while keeping the same bore on both sides of the turn. Compared with a short elbow, a bend generally sweeps through a gentler curve, which helps water change direction more smoothly in larger lines.

Each end takes a male-threaded 4" GI pipe or a threaded nipple. Seal the male threads with tape or jointing compound, screw each pipe fully home, and set the bend's alignment before the final turn, because a threaded fitting cannot be backed off without loosening the joint. Anchor the pipes close to the turn, where line forces act, and check the finished run against the 14 bar rating during pressure testing.

What to Specify When Ordering

• Quantity of 4" bends for each route or site.
• Confirmation that the line is 4" nominal diameter GI pipe with male-threaded ends.
• Whether a bend or a short elbow suits the space available at each corner.
• Other fittings needed on the same line, such as crosses, nipples or plugs.

Supplier

Jain Scientific Equipments Private Limited, which trades as ScienceLab and is known to many buyers as a laboratory equipment exporter from India, also supplies water-supply fittings such as this 4" bend. The company sources the item and handles quotation, packing and dispatch from Ambala, Haryana, so a buyer can combine pipe fittings with other water, sanitation and hygiene supplies in one order. Company background is available on the ScienceLab profile page.

Related Water, Sanitation & Hygiene Supplies

Fittings that are usually planned on the same galvanised line as this bend:

• Cross equal fthd GI 4" ND 14 Bar — a four-way junction in the same size for branching the main before or after the turn.
• Elbow 90º equal fthd GI ND 14 Bar — the tighter-turn alternative where corner space is limited.
• Nipple Taper mthd Hex GI 14 Bar — a male-threaded connector for joining the bend directly to another female fitting; confirm the size with us.
• Cap fthd GI 14 Bar — a female-threaded cap for closing a male pipe end at the end of a run.

Browse all items in the Water, Sanitation & Hygiene Supplies category.

Frequently Asked Questions

Are both ends of the Bend 90º equal fxf GI 4" ND 14 Bar the same?
Yes. Both ends of the Bend 90º equal fxf GI 4" ND 14 Bar are internal (female) threads of the same 4-inch nominal diameter, which is what "fxf" and "equal" mean in the name. Each end accepts a male-threaded 4" GI pipe or nipple.

How is this bend different from a 90° elbow?
The Bend 90º equal fxf GI 4" ND 14 Bar and a 90° elbow both turn a line through a right angle, but a bend generally follows a longer, gentler curve while an elbow is more compact. Choose the bend where there is room and the elbow where space is tight.

What pressure can the 4" GI bend handle?
The Bend 90º equal fxf GI 4" ND 14 Bar is rated for 14 bar (200 lb per square inch). Size pumps and set test pressures so the line stays within this rating, and make sure every other fitting on the line meets it as well.

What material and finish does the bend have?
The Bend 90º equal fxf GI 4" ND 14 Bar is malleable cast iron, hot-dip galvanised to protect it against corrosion in water service. Threading is done after galvanising, leaving clean threads that engage GI pipe without scraping through built-up zinc.

Who supplies the Bend 90º equal fxf GI 4" ND 14 Bar?
ScienceLab, the trading name of Jain Scientific Equipments Pvt Ltd in Ambala, Haryana, supplies the Bend 90º equal fxf GI 4" ND 14 Bar. It sources the fitting and quotes it with other water-supply items for projects in India and international markets.

How do I get a price for a quantity of these bends?
To price the Bend 90º equal fxf GI 4" ND 14 Bar, send the quantity, delivery location and any other fittings on your list through the contact page. A quotation is then prepared for the complete order, including bulk or export quantities.

Request a Quote

Send your requirement for the Bend 90º equal fxf GI 4" ND 14 Bar through the ScienceLab contact page with quantity and destination, or place it in the enquiry cart while you browse the other GI fittings. One enquiry can cover every fitting on your pipe schedule.

Last updated: 24 September 2026

Elbow 90º equal fthd GI ND 14 Bar (Product Code: SLE/WDF/07) is a compact galvanised iron elbow used to make a tight right-angle turn in 4-inch threaded water pipework in pumping, storage and distribution installations. Its two equal outlets carry internal parallel threads of 4" nominal diameter and the fitting is rated for 14 bar, which suits plumbers working in confined pump rooms and valve chambers. It is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India.

Specifications

What Is the GI 90° Equal Elbow Used For?

An elbow is the fitting of choice where a 4-inch galvanised line has to change direction in a small footprint — at a pump outlet, where a riser leaves the floor, inside a valve pit or where pipes hug a wall. The Elbow 90º equal fthd GI ND 14 Bar turns the flow through a right angle within a short body, so the pipe can sit close to the surface it follows.

Its internal parallel threads receive male-threaded 4" GI pipe or nipples. With a parallel female thread the seal depends on careful thread preparation, so apply thread-sealing tape or jointing compound to the male thread and tighten evenly. Sharp turns add more flow resistance than a long bend, so on long pumped mains use bends where space allows and keep elbows for the tight spots.

What to Specify When Ordering

• The 4" size — the product name does not state it, so write "4 inch nominal diameter" in your enquiry.
• The quantity needed for each site or installation.
• Your system pressure, to confirm it stays within the 14 bar rating.
• Whether any corners would be better served by a longer bend.

Supplier

Buyers who know ScienceLab as a laboratory equipment supplier in India may not expect pipe fittings, but the company — the trading name of Jain Scientific Equipments Private Limited, Ambala — also supplies water, sanitation and hygiene items for institutional and project use. This elbow is sourced by the company and then quoted, packed and dispatched with the rest of an order. For more about the business, see the company profile.

Related Water, Sanitation & Hygiene Supplies

Items that work with this elbow on a 4" GI line or at a plastic-to-GI transition:

• Bend 90º equal fxf GI 4" ND 14 Bar — the gentler-curve alternative in the same size where there is room.
• Cross equal fthd GI 4" ND 14 Bar — a four-way junction for branching a 4" GI main.
• Adaptor PP Comp, HDPE 110mmxmthd GI. 4"O/ND-P — its male GI thread lets an HDPE pipe screw straight into the elbow's female outlet.
• Elbow PP Comp, HDPE 110mmxfthd 4" O/ND-P — a plastic elbow to use when the turn itself is the HDPE-to-GI change-over.

More fittings are listed in the Water, Sanitation & Hygiene Supplies category.

Frequently Asked Questions

What size is the Elbow 90º equal fthd GI ND 14 Bar?
The Elbow 90º equal fthd GI ND 14 Bar is 4-inch nominal diameter on both outlets, according to its specification, even though the size is not written in the product name. Mention "4 inch" when you enquire so the quotation matches your pipework.

What type of thread does the elbow have?
The Elbow 90º equal fthd GI ND 14 Bar has internal female parallel threads on both ends. It accepts male-threaded 4" GI pipe or nipples; seal the male threads with tape or jointing compound so the joint stays watertight under pressure.

What pressure is the 4" GI elbow rated for?
The Elbow 90º equal fthd GI ND 14 Bar carries a pressure rating of 14 bar, equal to 200 lb per square inch. Check your pump's delivery pressure and the line test pressure against this rating before installation.

Should I choose this elbow or a bend?
Choose the Elbow 90º equal fthd GI ND 14 Bar where space is tight, because its body turns the flow in a short distance. Where there is room, a 90° bend of the same size generally gives a smoother turn and less flow resistance on long mains.

Who supplies the Elbow 90º equal fthd GI ND 14 Bar?
Jain Scientific Equipments Pvt Ltd (ScienceLab) of Ambala, Haryana supplies the Elbow 90º equal fthd GI ND 14 Bar. The company sources it and can include it in one quotation with other GI fittings and water-supply items for buyers in India and international markets.

Can the elbow be quoted for an export project?
Yes, the Elbow 90º equal fthd GI ND 14 Bar can be quoted for export as well as domestic delivery. Share the quantity, destination and full fitting list through the contact page, and the quotation will cover the complete requirement.

Request a Quote

Ready to order? List the Elbow 90º equal fthd GI ND 14 Bar with its quantity on the contact form, or save it in the enquiry cart and send your whole list at once. Remember to state the 4" size in your message.

Last updated: 24 September 2026

Tee Reduction fthd GI 2½" x 2" ND 14 Bar (Product Code: SLE/WDF/08) is a galvanised iron reducing tee used to take a smaller 2-inch branch off a 2½-inch threaded water main in pressurised supply networks. The side outlet is reduced to 2" while the run stays at 2½", all three ends are internally threaded, and the fitting is rated for 14 bar. It is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India, for water-supply and institutional projects.

Specifications

What Is the GI Reducing Tee Used For?

Distribution lines often step down in size as they branch: the main carries the full flow while each branch serves a smaller building, tap stand or storage tank. The Tee Reduction fthd GI 2½" x 2" ND 14 Bar does this in one fitting — the main passes straight through at 2½" and the branch leaves at a right angle in 2" — so no separate reducing socket or bush is needed at the junction.

Install it with the straight run in line with the main and the reduced outlet pointing toward the branch. Because the internal threads are parallel, prepare each male pipe end with sealing tape or jointing compound before tightening. Where a branch may need isolating for repairs, plan a valve on the 2" side close to the tee, and pressure-test the finished network within the 14 bar rating.

What to Specify When Ordering

• Confirmation that the main is 2½" and the branch 2" nominal diameter GI pipe.
• The number of tees, usually one for each branch take-off.
• Working and test pressure of the network, so it stays within 14 bar.
• Any straight fittings needed in each size, such as sockets or nipples.

Supplier

ScienceLab, the trading name of Jain Scientific Equipments Private Limited, supplies this reducing tee from Ambala, Haryana as part of its range of water, sanitation and hygiene items. The company sources the fitting and answers each enquiry with a quotation that can bundle every fitting on a project's bill of quantities. Institutions that buy through laboratory equipment tenders in India sometimes include water-supply works as well, and this tee can be priced within the same response. More about the company is on the ScienceLab profile page.

Related Water, Sanitation & Hygiene Supplies

Other threaded GI items used when laying out branch lines:

• Tee 90° Equal fthd GI ½" ND 14 Bar — an equal tee for small-bore service branches further along the network.
• Socket Reduction fthd ¾" x ½" ND 14 Bar — steps smaller service lines down in size.
• Nipple Taper mthd Hex GI 14 Bar — a male-threaded connector for joining the tee to other female fittings; confirm the size you need.
• Plug Hollow mthd GI 14 Bar — closes the branch outlet until the branch line is laid.

The complete range is in the Water, Sanitation & Hygiene Supplies category.

Frequently Asked Questions

Which outlet of the Tee Reduction fthd GI 2½" x 2" ND 14 Bar is reduced?
The side (branch) outlet of the Tee Reduction fthd GI 2½" x 2" ND 14 Bar is the reduced one, at 2-inch nominal diameter, while the straight run is 2½ inch. All three ends are internally threaded to take male GI pipe.

What pressure rating does the reducing tee have?
The Tee Reduction fthd GI 2½" x 2" ND 14 Bar is rated for 14 bar (200 lb per square inch). The rating applies to the fitting itself, so confirm that the pipes, valves and other fittings on the same network are rated for at least the same pressure.

What is the tee made from?
The Tee Reduction fthd GI 2½" x 2" ND 14 Bar is malleable cast iron, hot-dip galvanised to resist corrosion in water service. Its parallel female threads are cut after galvanising, so the thread form stays clean and engages the pipe properly.

Why use a reducing tee instead of an equal tee and a reducer?
The Tee Reduction fthd GI 2½" x 2" ND 14 Bar branches and reduces in one fitting, which gives fewer threaded joints, a shorter assembly and fewer possible leak points than an equal tee combined with a separate reducing socket or bush.

Who supplies the Tee Reduction fthd GI 2½" x 2" ND 14 Bar?
Jain Scientific Equipments Pvt Ltd, which trades as ScienceLab from Ambala, Haryana, supplies the Tee Reduction fthd GI 2½" x 2" ND 14 Bar. It sources the fitting and quotes it for institutional, contractor and project buyers in India and international markets.

What details speed up a quotation?
For a quick quotation on the Tee Reduction fthd GI 2½" x 2" ND 14 Bar, give the quantity, the delivery location and a list of the other fittings on the job. Questions about documentation for the fitting can be raised on the contact page before ordering.

Request a Quote

Add the Tee Reduction fthd GI 2½" x 2" ND 14 Bar to the enquiry cart, or describe your branch layout on the contact page. We will reply with a quotation covering the tees and any related fittings you list.

Last updated: 24 September 2026

Tee 90° Equal fthd GI ½" ND 14 Bar (Product Code: SLE/WDF/09) is a small-bore galvanised iron tee used to split a ½-inch threaded water line into two equal branches for taps, basins and other service points. All three outlets share the same ½" nominal diameter with internal threads, and the fitting is rated for 14 bar, making it a routine item for plumbers fitting out a school laboratory setup in India or a campus washroom. It is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India.

Specifications

What Is the Half-Inch GI Equal Tee Used For?

Half-inch lines are the last stage of most water systems — the pipe that runs along a laboratory bench to its sink taps, feeds a row of wash basins or supplies a hand-wash point. The Tee 90° Equal fthd GI ½" ND 14 Bar lets one such line serve an extra outlet: water continues along the run and also leaves through the side branch at the same size.

Tighten small fittings with care, since over-tightening a half-inch joint strains the thread while too little torque leaves a weep. Wrap the male threads with sealing tape in the direction of the thread, start the pipe by hand, then finish with a wrench. Where several tees sit along a bench line, clip the pipe firmly between them so that repeated tap use does not work the joints loose.

What to Specify When Ordering

• The number of branch points on each line (one tee per take-off).
• Confirmation that the line is ½" nominal diameter GI pipe with male-threaded ends.
• Sockets, nipples or reducing fittings needed to reach each tap connection.

Supplier

Jain Scientific Equipments Private Limited trades as ScienceLab and supplies this half-inch tee, sourcing it for customers who need plumbing items alongside their laboratory or WASH orders. Quotations, packing and dispatch are handled from Ambala, Haryana. For vendor registration and export paperwork, the supplying company's details are IEC AAECJ8618A (DGFT) and GSTIN 06AAECJ8618A1ZT. Background on the business is on the ScienceLab company profile.

Related Water, Sanitation & Hygiene Supplies

Small-bore GI fittings that complete a tap or basin line:

• Socket equal fthd GI ½" ND 14 Bar — joins two lengths of half-inch pipe on the same line.
• Socket Reduction fthd ¾" x ½" ND 14 Bar — steps a three-quarter-inch feed down to the half-inch line the tee sits on.
• Cap fthd GI 14 Bar — closes the far end of a line; confirm the size with us.
• Plug Hollow mthd GI 14 Bar — seals a branch left ready for a future tap.

View every item in the Water, Sanitation & Hygiene Supplies category.

Frequently Asked Questions

What size is the Tee 90° Equal fthd GI ½" ND 14 Bar?
The Tee 90° Equal fthd GI ½" ND 14 Bar is half-inch nominal diameter on all three outlets, each with an internal female thread. As an equal tee, its branch is the same size as the run, so it suits standard half-inch service lines.

What pressure is the half-inch GI tee rated for?
The Tee 90° Equal fthd GI ½" ND 14 Bar is rated for 14 bar, equivalent to 200 lb per square inch. Check this rating against the pressure of your pump, overhead tank or mains supply before installation.

Can this tee be used on a laboratory bench water line?
Yes, the Tee 90° Equal fthd GI ½" ND 14 Bar can branch a half-inch galvanised supply line to feed extra taps or sinks on a laboratory bench, provided the rest of the line is half-inch GI pipe with male-threaded ends.

What are the tee's material and coating?
The Tee 90° Equal fthd GI ½" ND 14 Bar is malleable cast iron with a hot-dip galvanised coating, and its threads are cut after galvanising. The zinc layer protects the body from rust, while threading afterwards keeps the threads clean.

Who supplies the Tee 90° Equal fthd GI ½" ND 14 Bar?
Jain Scientific Equipments Pvt Ltd (ScienceLab), based in Ambala, Haryana, supplies the Tee 90° Equal fthd GI ½" ND 14 Bar. The company sources the fitting and can quote it with other plumbing and WASH items for customers in India and international markets.

Can small quantities be ordered, or only bulk?
Both small and bulk requirements for the Tee 90° Equal fthd GI ½" ND 14 Bar can be sent for quotation. State the exact quantity and delivery location on the contact page, and the reply will confirm what can be supplied.

Request a Quote

Put the Tee 90° Equal fthd GI ½" ND 14 Bar in the enquiry cart with the other half-inch fittings for your installation and submit the list, or write to us through the contact page with quantities and the delivery location.

Last updated: 24 September 2026

Socket Reduction fthd ¾" x ½" ND 14 Bar (Product Code: SLE/WDF/10) is a galvanised malleable iron reducing socket used to join a ¾-inch threaded water pipe to a ½-inch pipe in a straight line. Both ends are internally threaded, one at each nominal size, and the fitting carries a 14 bar pressure rating, so installers use it wherever a feeder narrows to a tap or appliance line. It is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India.

Specifications

What Is the Three-Quarter to Half-Inch Reducing Socket Used For?

Water systems usually carry flow in a larger pipe and narrow it close to the point of use. The Socket Reduction fthd ¾" x ½" ND 14 Bar makes that step in a straight run: the ¾" end takes the feeder pipe and the ½" end takes the smaller line that continues to a tap, valve, float valve or wash point. Because it keeps the pipe axis straight, it is neater than combining an elbow or tee with a separate bush.

Fit the larger pipe first and then the smaller, sealing each male thread with tape or jointing compound. A reducing socket is normally installed so that water flows from the larger size to the smaller one, so check the direction before tightening. As with any threaded joint, support the pipes on both sides so the fitting does not carry bending loads.

What to Specify When Ordering

• Confirmation that your feeder is ¾" and the outgoing line ½" nominal diameter GI pipe.
• The quantity required for each installation.
• Companion fittings in either size that should be quoted with it.

Supplier

This reducing socket is a sourced item supplied by ScienceLab, the trading name of Jain Scientific Equipments Private Limited in Ambala, Haryana. Known to schools and colleges as a laboratory equipment supplier in India, the company also sources plumbing and WASH items so that institutions and project buyers can place one consolidated order. You can read about the company on its profile page.

Related Water, Sanitation & Hygiene Supplies

Fittings often listed with a reducing socket on a service line:

• Socket equal fthd GI ½" ND 14 Bar — a straight coupling for joining two half-inch pipes after the reduction.
• Tee 90° Equal fthd GI ½" ND 14 Bar — branches the half-inch line so it can serve more than one outlet.
• Nipple Taper mthd Hex GI 14 Bar — a short male connector for joining the socket to a female-threaded valve or fitting; confirm the size.
• Cap fthd GI 14 Bar — ends a line neatly where no further outlet is needed.

Find more in the Water, Sanitation & Hygiene Supplies category.

Frequently Asked Questions

What sizes does the Socket Reduction fthd ¾" x ½" ND 14 Bar connect?
The Socket Reduction fthd ¾" x ½" ND 14 Bar connects a three-quarter-inch nominal diameter pipe to a half-inch pipe. Each end has an internal female thread, so both pipes need male-threaded ends.

Is the reducing socket galvanised?
Yes. The Socket Reduction fthd ¾" x ½" ND 14 Bar is malleable cast iron, hot-dip galvanised for protection against rust, with threads cut after galvanising so the zinc does not clog them. It is intended for galvanised water pipe.

What pressure is the reducing socket rated for?
The Socket Reduction fthd ¾" x ½" ND 14 Bar is rated for 14 bar, or 200 lb per square inch. Design the whole line so that its working and test pressures stay within this rating.

When should I use a reducing socket rather than a bush?
Use the Socket Reduction fthd ¾" x ½" ND 14 Bar when both pipes have male threads and you want a straight, in-line change of size. A bush suits a different case: reducing an existing female outlet on another fitting.

Who supplies the Socket Reduction fthd ¾" x ½" ND 14 Bar?
Jain Scientific Equipments Pvt Ltd, trading as ScienceLab in Ambala, Haryana, supplies the Socket Reduction fthd ¾" x ½" ND 14 Bar. It sources the fitting for institutions, contractors and project buyers in India and international markets.

How can I get a quotation for the reducing socket?
To get a quotation for the Socket Reduction fthd ¾" x ½" ND 14 Bar, send the quantity and delivery location through the contact page, or add it to the enquiry cart with the other fittings you need.

Request a Quote

Every quotation for the Socket Reduction fthd ¾" x ½" ND 14 Bar is prepared against your stated quantity and destination. Use the contact page to send those details, or collect the item in the enquiry cart along with the rest of your pipe fittings.

Last updated: 24 September 2026

Socket equal fthd GI ½" ND 14 Bar (Product Code: SLE/WDF/11) is a straight galvanised iron coupling used to join two lengths of ½-inch threaded water pipe end to end in supply and service lines. It has internal parallel threads of the same ½" nominal diameter at both ends and is rated for 14 bar, making it the simplest way to extend or repair a small-bore GI run. It is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India.

Specifications

What Is the Half-Inch GI Equal Socket Used For?

Galvanised pipe comes in fixed lengths, so any run longer than one length needs a joint, and the Socket equal fthd GI ½" ND 14 Bar provides it without changing size or direction. The same fitting is used for repairs: a corroded or cracked section is cut out, the new ends are threaded and a replacement piece is joined in with sockets. During a school laboratory setup in India, half-inch lines to sink taps are often extended this way when benches are added or moved.

Parallel internal threads rely on a good seal at the mating male thread, so apply sealing tape or compound evenly and screw both pipes in until they are firmly engaged from each side. Tighten the second pipe while holding the socket with another wrench, so the first joint is not disturbed. After assembly, flush the line and check the joint for weeping under normal pressure.

Supplier

ScienceLab is the name under which Jain Scientific Equipments Private Limited trades from Ambala, Haryana. Alongside laboratory apparatus, the company supplies sourced plumbing fittings such as this half-inch socket and quotes them on the same enquiry, so an institution can deal with one supplier for bench equipment and the water lines that serve it. The company profile has more background.

Related Water, Sanitation & Hygiene Supplies

Other fittings used on half-inch GI service lines:

• Socket Reduction fthd ¾" x ½" ND 14 Bar — for points where the line must step down in size instead of continuing straight.
• Tee 90° Equal fthd GI ½" ND 14 Bar — adds a same-size branch to the half-inch line.
• Nipple Taper mthd Hex GI 14 Bar — a male nipple that pairs with a socket to join two female fittings; confirm the size.
• Cap fthd GI 14 Bar — seals the open male end of a pipe that will be extended later.

All water, sanitation and hygiene items are grouped in the Water, Sanitation & Hygiene Supplies category.

Frequently Asked Questions

What does "equal" mean in the Socket equal fthd GI ½" ND 14 Bar?
"Equal" means both ends of the Socket equal fthd GI ½" ND 14 Bar are the same size, half-inch nominal diameter, so it joins two pipes of identical bore without any reduction. Both ends are internally threaded.

What kind of thread does the socket have?
The Socket equal fthd GI ½" ND 14 Bar has internal female parallel threads at both ends. It accepts male-threaded half-inch GI pipe; seal the male thread with tape or jointing compound for a watertight connection.

What is the pressure rating of the half-inch GI socket?
The Socket equal fthd GI ½" ND 14 Bar is rated for 14 bar, which is 200 lb per square inch. Keep the working and test pressure of the line within this value when planning the installation.

Can the socket be used to repair a damaged pipe?
Yes, the Socket equal fthd GI ½" ND 14 Bar is commonly used in repairs: remove the damaged length, thread the pipe ends and join in a new piece using sockets. Check the repaired joints for leaks under pressure before closing up.

Who supplies the Socket equal fthd GI ½" ND 14 Bar?
The Socket equal fthd GI ½" ND 14 Bar is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab) of Ambala, Haryana. The company sources it and quotes it with other GI fittings for schools, institutions and project buyers in India and international markets.

What should an enquiry for the socket include?
An enquiry for the Socket equal fthd GI ½" ND 14 Bar should give the quantity, the delivery location and any other fittings you need. Use the contact page or enquiry cart; questions about documentation for the fitting can be raised there too.

Request a Quote

Sockets are usually ordered in quantity with the rest of a pipe schedule. Add the Socket equal fthd GI ½" ND 14 Bar to the enquiry cart, or send your full list through the contact page for a single consolidated quotation.

Last updated: 24 September 2026

Clamp Saddle PP, HDPE 110mm x fthd ½" O/ND-P (Product Code: SLE/WDF/12) is a polypropylene clamp saddle used to take a ½-inch threaded service connection off a 110 mm HDPE water main without cutting the main. It clamps around the pipe, has a single middle outlet with a female thread for GI pipe and is rated for 10 bar at 20°C, which suits crews connecting tap stands and buildings. It is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India.

Specifications

What Is the 110 mm HDPE Clamp Saddle Used For?

When a new house connection, tap stand or school water point has to be fed from an existing HDPE main, a clamp saddle is the least disruptive way to do it. The Clamp Saddle PP, HDPE 110mm x fthd ½" O/ND-P closes around a 110 mm outside-diameter HDPE pipe, and the half-inch galvanised service line is then screwed into its female-threaded outlet.

Typical practice is to fit the saddle on a clean, undamaged section of pipe, tighten the clamp evenly so the seal seats squarely, and then drill the main through the outlet with a suitable cutter. Keep the water temperature within 0 to 50°C, and note that the 10 bar rating is stated at 20°C; plastic fittings generally carry less pressure as temperature rises, so allow a margin in hot climates. The UV-stabilised polypropylene helps where the saddle is exposed to sunlight at a tap stand or open valve box.

What to Specify When Ordering

• Main pipe: 110 mm outside diameter HDPE.
• Branch: ½" GI pipe with a male-threaded end.
• Number of service connections (one saddle per tapping).
• Expected water temperature and pressure, to confirm they fall within 0 to 50°C and 10 bar at 20°C.

Supplier

Jain Scientific Equipments Private Limited, trading as ScienceLab from Ambala, Haryana, supplies this polypropylene clamp saddle as part of a wider range of HDPE, PVC and GI water fittings. Better known as a laboratory equipment supplier in India, the company sources the item and prepares single quotations for projects that need pipe fittings, pumps and hygiene supplies from one vendor. More about the company appears on the ScienceLab profile page.

Related Water, Sanitation & Hygiene Supplies

Items used on the same HDPE main or on the service line leaving the saddle:

• T, PP comp, HDPE 110 x 110 x 110mm OD-P — a full-size branch where a half-inch tapping would be too small.
• Adaptor PP Comp, HDPE 110mmxmthd GI. 4"O/ND-P — joins the same HDPE main to 4" GI sockets at a line end or pump.
• Socket equal fthd GI ½" ND 14 Bar — extends the half-inch GI service pipe leaving the saddle.
• Tee 90° Equal fthd GI ½" ND 14 Bar — splits the service line to feed two taps.

Browse the Water, Sanitation & Hygiene Supplies category for the full range.

Frequently Asked Questions

What pipe sizes does the Clamp Saddle PP, HDPE 110mm x fthd ½" O/ND-P fit?
The Clamp Saddle PP, HDPE 110mm x fthd ½" O/ND-P fits HDPE pipe of 110 mm outside diameter, and its outlet takes a half-inch nominal diameter GI pipe through a female thread. "O/ND" in the name stands for outside/nominal diameter.

What pressure and temperature is the saddle rated for?
The Clamp Saddle PP, HDPE 110mm x fthd ½" O/ND-P is rated for 10 bar at 20°C, with a suitable temperature range of 0 to 50°C. At higher water temperatures a plastic fitting's pressure capacity generally falls, so allow a margin in warm conditions.

What material is the clamp saddle made of?
The Clamp Saddle PP, HDPE 110mm x fthd ½" O/ND-P is reinforced, high-impact-strength polypropylene that is UV stabilised. The UV stabilisation helps the saddle withstand sunlight where it is installed above ground or in an open valve box.

Does the main need to be cut to fit the saddle?
No. The Clamp Saddle PP, HDPE 110mm x fthd ½" O/ND-P clamps around the existing 110 mm HDPE main, and the connection is made by drilling the pipe wall through the saddle outlet, so the main stays in one piece.

Who supplies the Clamp Saddle PP, HDPE 110mm x fthd ½" O/ND-P?
Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, Haryana, supplies the Clamp Saddle PP, HDPE 110mm x fthd ½" O/ND-P. It sources the saddle and quotes it for water-network, institutional and project buyers in India and international markets.

Can the saddle be quoted with other HDPE fittings?
Yes, the Clamp Saddle PP, HDPE 110mm x fthd ½" O/ND-P can be quoted together with the other HDPE, PVC and GI fittings on your list. Send the complete schedule and delivery location through the contact page for one consolidated price.

Request a Quote

Count the service connections you plan and send that number with your enquiry for the Clamp Saddle PP, HDPE 110mm x fthd ½" O/ND-P through the contact page. You can also add the saddle to the enquiry cart together with the GI fittings for each service line.

Last updated: 24 September 2026

Coupler PP Comp, HDPE 110mmxflng 4"O/ND-P (Product Code: SLE/WDF/13) is a polypropylene flanged coupling used to connect a 110 mm HDPE water pipe to 4-inch flanged GI pipework, valves or fittings. One end grips the HDPE pipe with a compression joint and the other is a flange, and the coupler is rated for 10 bar at 20°C, so pump-house and valve-chamber installers can move between plastic and metal lines. It is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India.

Specifications

What Is the HDPE-to-Flange Compression Coupler Used For?

Many water networks run in HDPE underground but meet metal at pump houses, storage tanks, meters and valve chambers, where equipment usually has flanged connections. The Coupler PP Comp, HDPE 110mmxflng 4"O/ND-P bridges that change: the 110 mm HDPE pipe is pushed into the compression end and locked by tightening the nut, while the flanged end bolts to a 4" GI flange or flanged fitting.

Because the joint is mechanical, it can be made without fusion-welding equipment, and the flanged side can later be unbolted for maintenance. Cut the HDPE pipe square, chamfer and clean the end, mark the insertion depth, and tighten the compression nut firmly. On the flange side, use a suitable gasket and tighten the bolts evenly in a cross pattern so the plastic flange is not distorted.

What to Specify When Ordering

• The drilling pattern of the mating 4" GI flange or equipment, so compatibility can be checked.
• Whether bolts, nuts and a gasket are needed with the coupler.
• The quantity, one per HDPE-to-flange connection.
• Operating pressure and temperature, which should stay within 10 bar at 20°C and 0 to 50°C.

Supplier

The coupler is supplied by ScienceLab, the trading name of Jain Scientific Equipments Private Limited of Ambala, Haryana. Better known as a lab equipment exporter, the company also sources HDPE, PVC and GI fittings for water, sanitation and hygiene projects. Institutional and tender buyers who need vendor details for registration can use GSTIN 06AAECJ8618A1ZT and LEI 3358004HRD1JIVXKYX49. Further information is on the company profile.

Related Water, Sanitation & Hygiene Supplies

Other transition and HDPE fittings for the same connection point:

• Adaptor PP Comp, HDPE 110mmxmthd GI. 4"O/ND-P — the threaded alternative when the GI side has a 4" socket instead of a flange.
• Elbow PP Comp, HDPE 110mmxfthd 4" O/ND-P — combines the HDPE-to-GI change-over with a right-angle turn.
• Coupler PVC Socket Solvent Cement Joint Flange, 110mm x 4" — the equivalent flanged coupler for uPVC pipe.
• Coupler Reducing PP Comp, HDPE 110x90mm OD-P — steps the HDPE line down to 90 mm elsewhere on the network.

See all items in the Water, Sanitation & Hygiene Supplies category.

Frequently Asked Questions

What does the Coupler PP Comp, HDPE 110mmxflng 4"O/ND-P connect?
The Coupler PP Comp, HDPE 110mmxflng 4"O/ND-P connects a 110 mm outside-diameter HDPE pipe to 4-inch nominal diameter flanged GI pipe or fittings. The HDPE side uses a compression joint and the other side is a flange.

Is welding needed to install the coupler?
No fusion welding is needed for the Coupler PP Comp, HDPE 110mmxflng 4"O/ND-P. The HDPE pipe is inserted into the compression end and the nut is tightened, while the flanged end is bolted to the mating flange with a gasket.

What pressure and temperature is the coupler rated for?
The Coupler PP Comp, HDPE 110mmxflng 4"O/ND-P is rated for 10 bar at 20°C, with a suitable temperature range of 0 to 50°C. Keep pump delivery and test pressures within this rating, allowing a margin in warm conditions.

Are bolts and a gasket included?
The product details for the Coupler PP Comp, HDPE 110mmxflng 4"O/ND-P do not state that bolts or a gasket are included. Please ask through the contact page, giving your flange details, and we will confirm what the quotation covers.

Who supplies the Coupler PP Comp, HDPE 110mmxflng 4"O/ND-P?
ScienceLab, the trading name of Jain Scientific Equipments Pvt Ltd in Ambala, Haryana, supplies the Coupler PP Comp, HDPE 110mmxflng 4"O/ND-P. It sources the fitting for water-network and institutional projects in India and international markets.

Is the coupler suitable for exposed locations?
The Coupler PP Comp, HDPE 110mmxflng 4"O/ND-P is made of reinforced, high-impact-strength polypropylene that is UV stabilised, which helps it tolerate sunlight in open valve chambers or pump yards. Keep it within the stated 0 to 50°C temperature range.

Request a Quote

For a price on the Coupler PP Comp, HDPE 110mmxflng 4"O/ND-P, send the quantity, your flange details and the delivery location through the contact page, or add it to the enquiry cart with the rest of the HDPE and GI fittings for the job.

Last updated: 24 September 2026