Water, Sanitation & Hygiene Supplies

Pump Centrifugal, Diesel 50cbm/hr (Product Code: SLE/PRP/01) is a self-priming, diesel-engine-driven centrifugal pumping set used to move large volumes of water in water supply, emergency response and dewatering work. It delivers 50 cubic metres per hour at around 2900 RPM against a 20 m total manometric head with 1 m suction head, and has a cast iron casing, shaft and impeller with a mechanical shaft seal. The pump is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India.

Specifications

What Is a Diesel Centrifugal Pump Used For?

A 50 cbm/hr diesel centrifugal pump moves water where there is no reliable mains power: filling storage tanks and water-trucking points from rivers or open wells, transferring water between reservoirs, feeding temporary distribution networks in camps and emergencies, and dewatering flooded sites or excavations. The trolley version is wheeled between points by hand, while the skid version can be bolted down as a semi-permanent pumping station.

Set the pump on level ground as close to the water as practical, because extra suction lift and long delivery lines both reduce flow below the rated 50 m³/h at 20 m head. Fill the casing with water before the first start, fit a strainer on the suction line to keep out debris, and store diesel well away from the water source to avoid contamination.

What to Specify When Ordering

• Mounting: trolley with 2 wheels and handlebar, or steel skid with carrying handles
• Suction and discharge diameter required: 50, 65, 75, 100 or 150 mm
• Your actual suction lift and delivery head, to check that the 20 m TMH duty point suits the site
• Quantity and delivery location

Supplier

Jain Scientific Equipments Private Limited, trading as ScienceLab, supplies this diesel centrifugal pumping set from Ambala, Haryana, as sourced water-supply equipment for WASH programmes, contractors, local bodies, NGOs and distributors in India and international markets. For vendor registration and export paperwork, the supplying company's details are IEC AAECJ8618A (DGFT) and GSTIN 06AAECJ8618A1ZT. More about the company is on the ScienceLab profile.

Related Water, Sanitation & Hygiene Supplies

Other pumping and pipework items used in water supply projects:

• Pump Electric sbmr bh 18cbm/hr — an electric submersible pump for boreholes with 3-phase power.
• Dewatering Pump, 11-22 cbm/hr@50m TMH — a smaller-flow pump rated at a higher head.
• Handpump Variant 3 Norm — a manual option for community water points.
• Coupler PP Comp, HDPE 110mmxflng 4"O/ND-P — a coupler for connecting HDPE delivery pipe to a flanged joint.

See the full Water, Sanitation & Hygiene Supplies range.

Frequently Asked Questions

What is the capacity of Pump Centrifugal, Diesel 50cbm/hr?
Pump Centrifugal, Diesel 50cbm/hr delivers 50 cubic metres per hour at around 2900 RPM, against a total manometric head of 20 m with a 1 m suction head. At higher heads or greater suction lift, the delivered flow will be lower than this rated figure.

What mounting options are available for the diesel centrifugal pump?
The diesel centrifugal pump can be mounted on a trolley with 2 wheels and a handlebar, or on a sturdy steel skid with carrying handles. The buyer must specify which one; the skid has pre-drilled holes so it can be bolted to a foundation.

What sizes are the suction and discharge connections on the 50 cbm/hr pump?
On the Pump Centrifugal, Diesel 50cbm/hr, suction inlet and discharge outlet diameters vary with pumping capacity, with sizes such as 50, 65, 75, 100 and 150 mm. State the pipe or hose size you plan to use so the quotation matches your connection.

What materials is the 50 cbm/hr diesel pump made of?
The 50 cbm/hr diesel pump has a pump casing, shaft and impeller made from cast iron, and the water seal on the shaft is mechanical. The pump is coupled directly to a diesel engine of matching power rather than driven through a belt.

Does the diesel centrifugal pump need priming?
Pump Centrifugal, Diesel 50cbm/hr is a self-priming pumping set, but like most self-priming pumps its casing should be filled with water before the first start. Keep the suction line airtight and fitted with a strainer so the pump can draw water reliably.

Who supplies Pump Centrifugal, Diesel 50cbm/hr?
Pump Centrifugal, Diesel 50cbm/hr is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, Haryana, India. It is quoted as sourced water-supply equipment to WASH programmes, contractors, NGOs and distributors in India and international markets; send enquiries through the contact page.

Request a Quote

To price Pump Centrifugal, Diesel 50cbm/hr, send your mounting choice, connection size and site head through the ScienceLab contact page, or add the pump to the enquiry cart with fittings and other WASH items.

Last updated: 24 September 2026

Pump Electric sbmr bh 18cbm/hr (Product Code: SLE/PRP/02) is a complete electric submersible borehole pump used to lift clean, non-aggressive groundwater from boreholes into tanks and water supply systems. Rated in its name at 18 cubic metres per hour, it runs on a directly coupled 3-phase 380/400 V, 50 Hz submersible motor of up to 7.5 kW, with stainless steel hydraulics and built-in dry-running protection. The pump is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India.

Specifications

What Is an Electric Submersible Borehole Pump Used For?

A submersible borehole pump sits down the borehole below the water level and pushes water up the rising main to an elevated tank, a distribution network or a water point. It suits piped water schemes for villages, schools, health centres and small towns wherever a 3-phase supply or a suitable generator is available, and it avoids the suction-lift limits of a surface pump.

Because the pump is meant for non-aggressive water without solid particles, develop the borehole and clear sand before installation, and keep the pump clear of the bottom of the hole. Set the level relay electrodes of the dry-running protection above the pump intake so the motor stops before the water falls too low. A qualified electrician should connect the 3-phase supply and check the direction of rotation at start-up.

What to Specify When Ordering

• The power available at site: 380 V or 400 V, 50 Hz, 3-phase
• Borehole depth, water levels and delivery head, so suitability can be checked
• The motor cable length needed to reach your control point
• Quantity and delivery location

Supplier

ScienceLab, the trading name of Jain Scientific Equipments Private Limited, supplies this submersible borehole pump from Ambala, Haryana, as sourced water-supply equipment. Water utilities, WASH programmes, drilling contractors, NGOs and distributors can request it together with handpumps, fittings and other water supply items for India and international markets. More about the company appears on the ScienceLab profile page.

Related Water, Sanitation & Hygiene Supplies

Pumps and pipework used alongside a borehole pump in water supply schemes:

• Pump Centrifugal, Diesel 50cbm/hr — a surface pump for high-volume transfer without grid power.
• Dewatering Pump, 11-22 cbm/hr@50m TMH — another pump in the range, rated 11–22 cbm/hr at 50 m head.
• Handpump SS-Riser 32ND — a manual borehole pump where power is not available.
• Handpump DA 9-15m Variant — another handpump option for community water points.
• Union Equal PVC, fxf, scj 10Bar 110mm OD-P — a PVC union for delivery pipework.

Browse the complete Water, Sanitation & Hygiene Supplies category.

Frequently Asked Questions

What does sbmr bh mean in Pump Electric sbmr bh 18cbm/hr?
In Pump Electric sbmr bh 18cbm/hr, "sbmr bh" is short for submersible borehole, and 18cbm/hr is the rated flow of 18 cubic metres per hour given in the product name. It is a complete electric pump designed to work down a borehole.

What power supply does the submersible borehole pump need?
The submersible borehole pump uses a 3-phase submersible motor for a 380 V/400 V, 50 Hz, 3-phase supply, with a motor rating of up to 7.5 kW. A single-phase version is not listed, so confirm your site power with us before ordering.

What water can the 18 cbm/hr submersible pump handle?
The 18 cbm/hr submersible pump is intended for non-aggressive water without solid particles. Sandy or corrosive water can shorten the life of pumps like this, so boreholes should be developed and cleared of sand, and the water quality checked, before installation.

How is the borehole pump protected against running dry?
Pump Electric sbmr bh 18cbm/hr has a built-in dry-running protection device, including level relay electrodes, that stops the motor when the water level drops too far. Its stator winding is hermetically enclosed in stainless steel, and the enclosure class is IP 58.

What is included with Pump Electric sbmr bh 18cbm/hr?
Pump Electric sbmr bh 18cbm/hr is a complete pump and motor unit with a priming screw, top non-return valve, bottom inlet strainer, water-lubricated bearings and motor cable. Rising main pipe, control panel and other installation items are not listed, so ask us about them.

Who supplies Pump Electric sbmr bh 18cbm/hr?
Pump Electric sbmr bh 18cbm/hr is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, Haryana, India, as sourced water-supply equipment. Utilities, WASH programmes, drilling contractors and distributors in India and international markets can request a quotation through the contact page.

Request a Quote

To price Pump Electric sbmr bh 18cbm/hr, send your site power, borehole details and cable length via the ScienceLab contact page, or add the pump to the enquiry cart with pipe fittings and other WASH supplies.

Last updated: 24 September 2026

Handpump Variant 3 Norm (Product Code: SLE/PRP/03) is a hand pump package with hot-dip galvanized above-ground equipment used to lift groundwater from boreholes at community water points, schools and field water-supply projects. Water, sanitation and hygiene (WASH) teams choose this variant when they plan to fit 65 mm nominal-diameter riser pipes with stainless steel couplings and stainless steel pump rods, which are ordered separately. The package is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India.

Specifications

What Is the Handpump Variant 3 Used For?

A hand pump of this kind lets people draw water from a borehole by working a handle at the pump head. The handle moves a string of pump rods, which drives a piston inside the cylinder at the bottom of the rising main and pushes water up the riser pipe to the spout. The Variant 3 Norm package provides the parts that sit on and above the well head — the galvanized head assembly, the water tank and the Normal Stand — so a project team can combine it with riser and rod lengths chosen for each borehole.

An open top cylinder is generally selected so the piston can be drawn up through the riser main for servicing without pulling every pipe out of the well, which suits water points looked after by local caretakers. Before installation, confirm the borehole depth and water level, the number of 65 mm riser lengths and stainless steel rods needed, and the platform design used at the site.

What to Specify When Ordering

• Number of Handpump Variant 3 Norm packages (one per borehole or water point).
• Borehole depth and planned cylinder setting, so riser pipe and rod quantities can be worked out.
• Riser pipes: 65 mm ND with stainless steel couplings, ordered as a separate line.
• Pump rods: stainless steel connecting rods with threaded couplers, ordered as a separate line.

Supplier

Jain Scientific Equipments Private Limited, which trades as ScienceLab, supplies this hand pump package from Ambala, Haryana, India. Alongside its work as a laboratory equipment supplier in India, the company sources water-supply hardware such as hand pumps, riser sets and pipe fittings for schools, institutions, NGOs and project buyers in India and international markets. It sources this pump rather than producing it, and handles the enquiry, quotation and dispatch. Company background is on the ScienceLab company profile page.

Related Water, Sanitation & Hygiene Supplies

These items from the same range are often considered alongside a hand pump package when planning a water point:

• Handpump SS-Riser 32ND — stainless steel riser pipe and connecting rod lengths for hand pumps built around 32 mm risers; compare riser sizes before ordering.
• Handpump DA 9-15m Variant — a direct action PVC hand pump set for shallow wells.
• Pump Electric sbmr bh 18cbm/hr — a powered borehole option where electricity is available.
• Pump Centrifugal, Diesel 50cbm/hr — an engine-driven pump for moving larger volumes of water.

See the full Water, Sanitation & Hygiene Supplies range.

Frequently Asked Questions

What is included in the Handpump Variant 3 Norm package?
The Handpump Variant 3 Norm package covers the hot-dip galvanized above-ground equipment — head assembly, water tank and Normal Stand — adapted for 65 mm riser pipes and fitted with an open top cylinder. Riser pipes and connecting rods are not part of the package and are ordered separately.

Which riser pipes and rods fit the Handpump Variant 3 Norm?
The Handpump Variant 3 Norm is described for use with 65 mm nominal-diameter riser pipes joined by stainless steel couplings, together with stainless steel connecting (pump) rods that have threaded couplers. Ask us to include matching riser and rod lengths in the same quotation.

How many riser pipes and rods does one Handpump Variant 3 Norm need?
The number of riser pipes and rods for a Handpump Variant 3 Norm depends on the depth at which the cylinder is set in each borehole, so there is no fixed count. Share the borehole depth and water level through our contact page and we will work out the lengths with you.

Why is the Handpump Variant 3 Norm hot-dip galvanized?
Hot-dip galvanizing gives the steel parts of the Handpump Variant 3 Norm a zinc coating, a common way to slow rusting on equipment that stands outdoors and is splashed with water every day. Keeping the pump surroundings clean and drained also helps the finish last longer.

Who supplies the Handpump Variant 3 Norm?
The Handpump Variant 3 Norm is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab) of Ambala, Haryana, India. The company sources the pump package and handles quotations, paperwork and dispatch for buyers in India and international markets.

What does a quotation for the Handpump Variant 3 Norm need?
A quotation for the Handpump Variant 3 Norm needs the number of pumps, the borehole depths, whether riser pipes and stainless steel rods should be priced with it, and the delivery destination. Add the item to the enquiry cart or send these details through the contact page.

Request a Quote

To price the Handpump Variant 3 Norm for a school, community or field project, send your quantities and borehole details through the contact page or add the item to the enquiry cart. ScienceLab replies with a quotation for supply within India and to international markets.

Last updated: 24 September 2026

Handpump SS-Riser 32ND (Product Code: SLE/PRP/04) is a 3-metre stainless steel riser pipe of 32 mm nominal diameter, paired with one stainless steel connecting rod, used to build the rising main and rod string of a hand pump installed in a borehole or well. Drilling contractors and water-supply programmes order it length by length, because every riser pipe comes with its own 10.8 mm diameter rod. It is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India.

Specifications

What Is the SS Riser Pipe and Rod Set Used For?

In a lever-type hand pump, the riser pipes form the column that carries water from the cylinder up to the pump head, while the connecting rods inside that column transfer the handle's up-and-down movement to the piston. The Handpump SS-Riser 32ND provides both parts in matching 3-metre lengths, so the installer screws one pipe onto the coupling of the last and joins the rods through their M12 threads as the string is lowered.

Keep the HDPE thread protectors in place until each pipe is about to be joined, because damaged threads are a common cause of leaking joints. Lay pipes and rods on clean supports rather than bare ground during installation, and count the lengths against the planned cylinder depth before the crew goes to site.

What to Specify When Ordering

• Number of riser sets, based on the cylinder setting depth divided by the 3-metre length of each set.
• The hand pump model the sets will be used with, so the 32 mm riser and M12 rod threads can be checked against it.
• Number of boreholes or water points to be equipped.

Supplier

These stainless steel riser sets are supplied by Jain Scientific Equipments Private Limited, the company behind the ScienceLab name, from Ambala in Haryana, India. The company sources rising-main components and other water-point hardware for contractors, NGOs, schools and institutional buyers, and co-ordinates quotations and dispatch within India and to international markets. More about the company is on the ScienceLab profile page.

Related Water, Sanitation & Hygiene Supplies

Other water-supply items in the same range that buyers compare when planning hand pump installations:

• Handpump Variant 3 Norm — a galvanized above-ground pump package described for 65 mm risers; check riser size compatibility first.
• Handpump DA 9-15m Variant — a direct action pump set that uses a PVC riser main instead of steel.
• Pump Electric sbmr bh 18cbm/hr — an electric borehole pump for sites with a power supply.

Browse the complete Water, Sanitation & Hygiene Supplies category.

Frequently Asked Questions

What comes with each Handpump SS-Riser 32ND?
Each Handpump SS-Riser 32ND consists of one 3-metre stainless steel riser pipe of 32 mm nominal diameter, with a female threaded coupling on one end and an HDPE thread protector on the other, plus one 3-metre stainless steel 304 connecting rod of 10.8 mm diameter.

What thread does the Handpump SS-Riser 32ND connecting rod use?
The connecting rod of the Handpump SS-Riser 32ND has an M12 rolled male thread at one end and an M12 stainless steel female threaded coupling welded at the other, so successive rods screw directly into one another as the rod string is assembled.

How many Handpump SS-Riser 32ND sets does a borehole need?
The number of Handpump SS-Riser 32ND sets equals the cylinder setting depth divided by 3 metres, rounded up, because each set adds one 3-metre pipe and one 3-metre rod. Confirm the final count against the pump maker's installation drawing for that borehole.

Does the Handpump SS-Riser 32ND fit the Handpump Variant 3 Norm?
Not as described: the Handpump SS-Riser 32ND is a 32 mm nominal-diameter riser, while the Handpump Variant 3 Norm is described for a larger riser pipe size. Tell us the pump model you are using through the contact page and we will check which riser set applies.

Why are the Handpump SS-Riser 32ND pipe and rod made of stainless steel?
Stainless steel is widely used for hand pump riser pipes and rods such as the Handpump SS-Riser 32ND because it resists corrosion in groundwater better than plain steel, which helps keep water clear of rust and reduces how often below-ground parts need replacing.

Who supplies the Handpump SS-Riser 32ND?
The Handpump SS-Riser 32ND is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India, which sources the riser sets and quotes them for project, institutional and export buyers. Send quantities and delivery details through the contact page or the enquiry cart.

Request a Quote

For a price on the Handpump SS-Riser 32ND, list the number of sets and the delivery location on the contact page, or add the item to the enquiry cart together with any pumps from the same range.

Last updated: 24 September 2026

Handpump DA 9-15m Variant (Product Code: SLE/PRP/05) is a direct action (low-lift, shallow-well) hand pump set used to draw water from shallow boreholes at community, school and camp water points. Its specification covers cylinder installation depths of 9 to 12 metres, with a glued (solvent-cemented) PVC riser main, PVC pump rods, well screen, sand trap and installation tools in the set. It is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India.

Specifications

What Is the Direct Action Handpump Used For?

A direct action hand pump has no lever mechanism: the user lifts and pushes the handle, which moves the pump rod and piston straight up and down inside the cylinder. That makes it well suited to shallow water tables, where the lift is short and the pump can be installed and maintained by a small trained team. The Handpump DA 9-15m Variant arrives as a complete set, from the handle and pump body at the surface down to the well screen and sand trap at the bottom of the borehole.

During installation, the PVC raising mains and pump rods are joined with the supplied solvent cement, the reducers step the casing down to the 48 mm lower casing, and the bottom flange is bolted to a concrete platform around the well head. The two spanners and the retrieving rod stay with the caretaker for routine maintenance of the below-ground parts.

What to Specify When Ordering

• Planned cylinder setting depth for each borehole (the listed specification covers 9 to 12 metres).
• Number of pump rod and raising main lengths needed beyond the standard set for that depth.
• Casing pipe size at the site, so the 89 mm OD reducing socket matches it.
• Number of complete pump sets required.

Supplier

Jain Scientific Equipments Private Limited, known to customers as ScienceLab, supplies this direct action pump set from Ambala, Haryana, India, sourcing it for water-supply projects run by NGOs, contractors, schools and public bodies in India and international markets. For vendor registration, the supplying company's details are GSTIN 06AAECJ8618A1ZT and LEI 3358004HRD1JIVXKYX49. Read more on the ScienceLab profile page.

Related Water, Sanitation & Hygiene Supplies

Compare this shallow-well pump with other water-lifting options in the range:

• Handpump Variant 3 Norm — a galvanized hand pump package for 65 mm riser pipes and stainless steel rods.
• Handpump SS-Riser 32ND — stainless steel riser pipe and rod lengths for steel rising mains.
• Pump Electric sbmr bh 18cbm/hr — an electric borehole pump where mains or generator power is available.
• Pump Centrifugal, Diesel 50cbm/hr — a diesel pump for high-volume surface water transfer.

All water-point items are listed under Water, Sanitation & Hygiene Supplies.

Frequently Asked Questions

What depth is the Handpump DA 9-15m Variant designed for?
The listed specification of the Handpump DA 9-15m Variant covers cylinder installation depths of 9 to 12 metres. For a setting closer to the 15 metres in the product name, confirm the extra pipe and rod lengths with us through the contact page before ordering.

What is included in the Handpump DA 9-15m Variant set?
The Handpump DA 9-15m Variant set includes the handle and pump body assemblies, bottom flange, PVC pump rods and raising mains, piston assembly, cylinder with foot valve, well screen, reducers, lower casing, sand trap, two spanners, a retrieving rod and a bottle of solvent cement.

How are the pipes of the Handpump DA 9-15m Variant joined?
The PVC raising mains and pump rods of the Handpump DA 9-15m Variant have threaded joints that are glued with solvent cement; a 250 ml bottle of cement in an aluminium extruded bottle with PE stopper is part of the set. Joints should be clean and dry before cementing.

How is the Handpump DA 9-15m Variant mounted?
The Handpump DA 9-15m Variant is mounted with a bottom flange assembly, bolts and an intermediate conical flange that bolt onto a concrete platform built around the well head. The concrete platform itself is prepared on site and is not among the listed items.

Which casing does the Handpump DA 9-15m Variant reducer fit?
The reducing socket of the Handpump DA 9-15m Variant has an 88.5 mm inside diameter at the top to fit an 89 mm OD PVC casing pipe, and the cylinder reducer steps down to fit the 48 mm OD PVC lower casing supplied in the set.

Who supplies the Handpump DA 9-15m Variant?
The Handpump DA 9-15m Variant is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India. The company sources the pump set and quotes it for WASH projects, contractors and institutional buyers in India and international markets.

Request a Quote

Send the number of pump sets, your borehole depths and the delivery location through the contact page, or place the Handpump DA 9-15m Variant in the enquiry cart to receive a quotation.

Last updated: 24 September 2026

Reusable Menstrual Set (Product Code: SLE/SAH/01) is a kit of washable cloth sanitary pads used for menstrual protection by women and girls at home, in schools and in humanitarian hygiene distributions. Each set combines two straight pads, three winged pads, two cotton holders and a storage pouch, made to be washed and reused for a minimum of one year. The set is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India.

Specifications

What Is the Reusable Menstrual Set Used For?

The set supports menstrual hygiene management where disposable pads are costly, hard to obtain or difficult to dispose of. A pad is placed in a cotton holder, which is fastened with its ribbon bands; the absorbent flannel-type cotton faces the body and the synthetic backing helps stop leaks. Straight and winged shapes let the user choose what feels secure for the day, and the pouch keeps clean or used pads out of sight until they can be washed.

Schools and relief programmes often hand out the set together with soap and laundry powder, since pads need a thorough wash with soap and clean water and complete drying, ideally in sunlight, before reuse. Short guidance on washing, drying and private storage helps girls use the kit with confidence.

What to Specify When Ordering

• Number of sets, usually one per girl or woman in the distribution.
• Preferred colour: grey or light brown.
• Whether soap bars or laundry powder should be quoted with the sets for a complete hygiene pack.

Supplier

Jain Scientific Equipments Private Limited trades under the ScienceLab name and supplies this menstrual hygiene set from Ambala, Haryana, India. Besides school laboratory items, the company sources personal hygiene supplies for education departments, NGOs and relief agencies, and consolidates them with other hygiene-kit items on a single quotation for India and international markets. See the ScienceLab company profile for background.

Related Water, Sanitation & Hygiene Supplies

Items commonly packed with reusable menstrual sets in hygiene kits:

• Soap Toilet Bar Approx. 100-110g Wrapped — perfume-free bar soap for washing the pads and for personal hygiene.
• Laundry Detergent/Washing Powder, 1.5kg — concentrated powder for hand washing cloth items.
• Multipurpose Cloth Cotton 1x1.5m — a cotton cloth that can serve many household hygiene uses.
• Soap Box Plastic — keeps the soap bar clean and dry between washes.

The full range is in Water, Sanitation & Hygiene Supplies.

Frequently Asked Questions

What is in each Reusable Menstrual Set?
Each Reusable Menstrual Set contains two straight pads, three winged pads, two holders made of cotton and one pouch for storage. The holders have ribbon bands that keep the pads in position, and the pouch keeps the pieces together between uses.

How long can the Reusable Menstrual Set be used?
The Reusable Menstrual Set is made to be used and reused for a minimum of one year, with workmanship intended to withstand multiple washes over that period. Careful washing and full drying after each use help the pads keep their shape and absorbency.

What are the pads in the Reusable Menstrual Set made of?
The pads in the Reusable Menstrual Set are made of cotton, preferably flannel, on one side for high absorbency, with a synthetic material on the flip side for protection against leakage. The holders are also cotton, with edges finished by over-locking or similar stitching.

Which colours does the Reusable Menstrual Set come in?
The Reusable Menstrual Set is offered in grey or light brown. State the colour you prefer, or whether a mix is acceptable, when you send your enquiry so the quotation matches your distribution plan.

How should the Reusable Menstrual Set be washed?
Pads from the Reusable Menstrual Set should be rinsed in cool water, washed with soap, rinsed again and dried completely, preferably in sunlight, before being stored in the pouch. Never store the pads while still damp.

Who supplies the Reusable Menstrual Set?
The Reusable Menstrual Set is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India, which sources the sets for schools, NGOs and relief programmes. Bulk quantities for India and international markets can be quoted through the contact page.

Request a Quote

Tell us how many Reusable Menstrual Sets you need, your colour preference and the delivery destination on the contact page, or add the set and other hygiene items to the enquiry cart.

Last updated: 24 September 2026

Soap Toilet Bar Approx. 100-110g Wrapped (Product Code: SLE/SAH/02) is a wrapped, perfume-free toilet soap bar used for handwashing and bathing in households, schools, hostels and hygiene-kit distributions. Its specification calls for a minimum of 75% total fatty matter, no animal fat and a biodegradable formula described as suitable for all skin types. It is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India.

Specifications

What Is the Toilet Soap Bar Used For?

Handwashing with soap and water is one of the simplest hygiene habits taught in schools and promoted in water, sanitation and hygiene (WASH) programmes, and a bar soap is the everyday tool for it. This wrapped bar is meant for washing hands and for bathing; its perfume-free formula and moisturizing ingredients make it a practical choice for large groups where users have different skin types.

Total fatty matter is the main measure of a toilet soap's quality: a higher TFM generally means a harder bar that lathers well and lasts longer in daily use. Keep bars in a drained soap box between uses so they do not soften, and store cartons in a cool, dry place away from direct sun.

What to Specify When Ordering

• Number of bars (or number of hygiene kits and bars per kit).
• Whether soap boxes should be quoted with the bars.
• Any composition details your programme needs in writing, such as TFM or palm-oil sourcing, so we can confirm them with the quotation.

Supplier

This soap bar is supplied by Jain Scientific Equipments Private Limited, whose trading name is ScienceLab, from Ambala, Haryana, India. The company sources hygiene consumables such as soap, toothpaste and laundry powder for schools, hostels, NGOs and relief buyers, and brings them together with other hygiene-kit items for delivery within India and to international markets. Company details are on the ScienceLab profile page.

Related Water, Sanitation & Hygiene Supplies

Handwashing and personal hygiene items that pair with this soap bar:

• Soap Box Plastic — a two-piece box that keeps the bar clean and dry.
• Hand Wash Station — a handwashing point for schools and public spaces.
• Hand sanitizer Alcohol >60% 500ml w. Pump — for hand hygiene when soap and water are not at hand.
• Laundry Detergent/Washing Powder, 1.5kg — for washing clothes and cloth items in the same kit.

See more in Water, Sanitation & Hygiene Supplies.

Frequently Asked Questions

What does the weight of the Soap Toilet Bar Approx. 100-110g Wrapped mean?
The Soap Toilet Bar Approx. 100-110g Wrapped is specified at 100 g, and the product name gives an approximate band of 100-110 g per bar. If your tender requires a fixed minimum weight, state it in your enquiry so we can confirm it before quoting.

What is the total fatty matter of the Soap Toilet Bar Approx. 100-110g Wrapped?
The Soap Toilet Bar Approx. 100-110g Wrapped is specified with a total fatty matter content of at least 75%. TFM is the usual quality measure for toilet soap, and higher values generally give a firmer bar with good lather.

Is the Soap Toilet Bar Approx. 100-110g Wrapped perfume-free?
Yes, the Soap Toilet Bar Approx. 100-110g Wrapped is specified as perfume-free and free from animal fat, with natural humectants and moisturizing ingredients. It is described as suitable for all skin types, including dry and sensitive skin.

How long does the Soap Toilet Bar Approx. 100-110g Wrapped keep?
Shelf life of the Soap Toilet Bar Approx. 100-110g Wrapped depends on the production batch and storage conditions, so we do not quote a fixed period. Ask us for the expiry date of the batch you are quoted, and store cartons in a cool, dry place.

Who supplies the Soap Toilet Bar Approx. 100-110g Wrapped?
The Soap Toilet Bar Approx. 100-110g Wrapped is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India. The company sources the soap and quotes it for bulk hygiene programmes, schools and institutions in India and international markets.

What should a quotation request for the Soap Toilet Bar Approx. 100-110g Wrapped include?
A quotation request for the Soap Toilet Bar Approx. 100-110g Wrapped should include the number of bars, any specification points you need confirmed in writing and the delivery destination. Send it via the contact page.

Request a Quote

To receive prices for the Soap Toilet Bar Approx. 100-110g Wrapped, share your quantity and destination on the contact page or add it to the enquiry cart with the rest of your hygiene-kit list.

Last updated: 24 September 2026

Hand sanitizer Alcohol >60% 500ml w. Pump (Product Code: SLE/SAH/03) is an alcohol-based hand sanitizer in a 500 ml pump bottle, used for hand antisepsis in offices, households, classrooms and other shared spaces. Its alcohol content lies between 60% and 80%, and it is fragrance-free, with no colorants, dyes or perfumes. It is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India.

Specifications

What Is the 500 ml Hand Sanitizer Used For?

An alcohol-based hand rub is used to clean hands when soap and running water are not close by — at office desks, reception counters, classroom doors, staff rooms and at home. The 500 ml pump bottle suits a fixed spot on a desk or shelf, where people take one pump, rub it over all surfaces of both hands and let it dry fully; it does not replace handwashing when hands are visibly dirty.

Because the product contains 60-80% alcohol, it is flammable: keep bottles away from flames, heaters and direct sun, close the pump when not in use, and place dispensers where young children can use them only under supervision. Its fragrance-free, dye-free formula is useful in shared spaces where some users are sensitive to scents.

What to Specify When Ordering

• Number of 500 ml pump bottles.
• Any exact alcohol percentage your policy requires within the 60-80% range, so it can be confirmed for the quoted batch.
• Whether smaller personal bottles or gel sanitizer from the same range should be quoted together.

Supplier

ScienceLab, the trading name of Jain Scientific Equipments Private Limited in Ambala, Haryana, India, supplies this hand sanitizer as part of its hygiene and sanitation range. The company sources it for schools, offices, institutions and programme buyers, and can combine it with soap, disinfectant and cleaning items on one quotation for India and international markets. Learn more on the ScienceLab profile page.

Related Water, Sanitation & Hygiene Supplies

Other hand hygiene products in the same range:

• Alcohol Hand Sanitizer, 150ml — a smaller bottle for personal carry.
• Alcohol Hand Sanitizer Gel — a gel format for users who prefer it to a liquid.
• Hand Wash Station — a handwashing point for washing with soap and water.
• Soap Toilet Bar Approx. 100-110g Wrapped — perfume-free bar soap for routine handwashing.

Browse Water, Sanitation & Hygiene Supplies for the complete list.

Frequently Asked Questions

What alcohol percentage does the Hand sanitizer Alcohol >60% 500ml w. Pump contain?
The Hand sanitizer Alcohol >60% 500ml w. Pump contains not less than 60% and not more than 80% alcohol. If your organisation specifies an exact figure within that range, mention it in your enquiry so it can be confirmed for the batch being quoted.

Is the Hand sanitizer Alcohol >60% 500ml w. Pump fragrance-free?
Yes, the Hand sanitizer Alcohol >60% 500ml w. Pump is fragrance-free and contains no colorants, dyes or perfumes. It is specified not to cause skin irritation or allergies, which makes it practical for shared use in offices and households.

What size is the Hand sanitizer Alcohol >60% 500ml w. Pump?
The Hand sanitizer Alcohol >60% 500ml w. Pump comes in a 500 ml bottle fitted with a pump dispenser, sized for a desk, counter or shelf. For personal carry, the smaller personal-size bottle in the same range may suit better.

What is the shelf life of the Hand sanitizer Alcohol >60% 500ml w. Pump?
Shelf life of the Hand sanitizer Alcohol >60% 500ml w. Pump depends on the chemical, its grade and storage conditions, so no fixed period is stated. Ask us for the expiry date of the batch you are quoted, and store bottles closed, away from heat.

Who supplies the Hand sanitizer Alcohol >60% 500ml w. Pump?
The Hand sanitizer Alcohol >60% 500ml w. Pump is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India, which sources it for schools, offices and institutions. Bulk quantities for India and international markets are quoted through the contact page.

Request a Quote

Send the number of bottles and the delivery location for the Hand sanitizer Alcohol >60% 500ml w. Pump through the contact page, or add it to the enquiry cart alongside other hygiene supplies.

Last updated: 24 September 2026

Toothpaste for Children 75ml (Product Code: SLE/SAH/04) is a 75 ml, neutral-flavoured, non-fluoride toothpaste used for children's daily tooth brushing at home, in boarding schools and in hygiene-kit distributions. It is formulated without fluoride so it can also be issued in regions where drinking water already carries excess fluoride. It is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India.

Specifications

What Is the Children's Toothpaste Used For?

This toothpaste is part of a child's daily oral hygiene routine and is often packed into school hygiene kits with a soft children's toothbrush. The neutral flavour keeps it acceptable to children who dislike strong mint, and the fluoride-free formula lets programmes issue one product across districts where groundwater fluoride is already high.

Teachers and caregivers usually show younger children how to use only a small smear of paste, brush all tooth surfaces gently and spit out rather than swallow. Brushing time in school health sessions is a good moment to pair the toothpaste with handwashing practice.

What to Specify When Ordering

• Number of 75 ml packs for children.
• Whether the adult 75 ml toothpaste is needed for the same distribution.
• Whether children's toothbrushes should be quoted with the toothpaste.

Supplier

ScienceLab is the trading name of Jain Scientific Equipments Private Limited, Ambala, Haryana, India, which supplies this children's toothpaste within its personal hygiene range. The company sources it for schools, hostels, NGOs and relief programmes and packs it into consolidated hygiene-kit orders for India and international markets. Institutional buyers completing vendor registration can record the supplying company as Jain Scientific Equipments Private Limited, CIN U29309HR2020PTC087597, GSTIN 06AAECJ8618A1ZT. See the ScienceLab profile for more.

Related Water, Sanitation & Hygiene Supplies

Oral and personal hygiene items that go with this toothpaste:

• Toothbrush for Children — a soft, small-size brush to use with the paste.
• Toothpaste for Adults 75ml — the adult non-fluoride version for family kits.
• Toothbrush for Adult — a medium-hardness brush for older users in the household.
• Soap Toilet Bar Approx. 100-110g Wrapped — for handwashing before and after brushing.

See all items in Water, Sanitation & Hygiene Supplies.

Frequently Asked Questions

Does the Toothpaste for Children 75ml contain fluoride?
No, the Toothpaste for Children 75ml is non-fluoride. It is specified this way so it can also be used in regions where the water already has excess levels of fluoride, allowing one product to be distributed across different areas.

What flavour is the Toothpaste for Children 75ml?
The Toothpaste for Children 75ml has a neutral flavour. A mild, neutral taste is generally easier for young children to accept than a strong mint, which helps them keep up a daily brushing habit.

How much does one pack of Toothpaste for Children 75ml contain?
One pack of Toothpaste for Children 75ml contains 75 ml of toothpaste. Tell us how many children a distribution covers and how long the supply should last, and we will help you work out the number of packs.

What is the shelf life of the Toothpaste for Children 75ml?
The shelf life of the Toothpaste for Children 75ml depends on the production batch and storage conditions, so no fixed period is stated here. Ask us for the expiry date of the batch you are quoted, and store cartons in a cool, dry place.

Who supplies the Toothpaste for Children 75ml?
The Toothpaste for Children 75ml is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India, which sources it for school and relief hygiene kits. Quotations for India and international markets are available through the contact page.

Request a Quote

To order the Toothpaste for Children 75ml, send your quantity and delivery destination via the contact page or add it to the enquiry cart with matching toothbrushes.

Last updated: 24 September 2026

Toothpaste for Adults 75ml (Product Code: SLE/SAH/05) is a 75 ml non-fluoride toothpaste used for adult oral hygiene in households, hostels, staff quarters and community hygiene-kit distributions. Buyers can choose it unflavoured or with peppermint flavour, and its fluoride-free formula makes it usable where local water already contains excess fluoride. It is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India.

Specifications

What Is the Adult Toothpaste Used For?

Adult toothpaste is a basic item in family hygiene kits, hostel supply lists and institutional stores, used with a toothbrush for twice-daily cleaning of teeth and gums. This 75 ml pack is sized for individual issue, so each adult in a household or dormitory can receive a personal supply rather than sharing a large tube.

Programmes working in areas with high natural fluoride in groundwater often prefer a non-fluoride paste for everyone, and this product fits that need. Choose peppermint where users expect a fresh taste, or the unflavoured option for people who find mint too strong.

What to Specify When Ordering

• Flavour: unflavoured or peppermint (or a split between the two).
• Number of 75 ml packs for adults.
• Whether adult toothbrushes, or the children's toothpaste, should be quoted in the same order.

Supplier

Jain Scientific Equipments Private Limited, operating as ScienceLab from Ambala, Haryana, India, supplies this adult toothpaste. The company sources everyday hygiene products for hostels, institutions, NGOs and humanitarian buyers and consolidates them with brushes, soap and cleaning items so a whole kit can be quoted and shipped together to destinations in India and international markets. Visit the ScienceLab profile page for company information.

Related Water, Sanitation & Hygiene Supplies

Items that complete an adult oral and personal hygiene kit:

• Toothbrush for Adult — an individually wrapped, medium-hardness brush.
• Toothpaste for Children 75ml — a neutral-flavour, non-fluoride paste for children in the same household.
• Toothbrush for Children — a soft, small-size brush for younger family members.
• Nail Clipper Metal Medium Size — another personal grooming item often included in hygiene kits.

Explore the Water, Sanitation & Hygiene Supplies category.

Frequently Asked Questions

Which flavours are available for the Toothpaste for Adults 75ml?
The Toothpaste for Adults 75ml is available with no flavour or with peppermint flavour. You can order one option or split the quantity between both; state your choice in the enquiry so the quotation lists the correct variant.

Is the Toothpaste for Adults 75ml fluoride-free?
Yes, the Toothpaste for Adults 75ml is non-fluoride. It is intended to be usable in regions where water sources already contain excess fluoride, so a single product can serve distributions in different areas.

How big is a pack of Toothpaste for Adults 75ml?
Each pack of Toothpaste for Adults 75ml holds 75 ml of paste, a size convenient for issuing one pack per person in a family kit, hostel or staff hygiene allowance. Larger distributions are simply quoted by the number of packs.

How long does the Toothpaste for Adults 75ml keep?
The Toothpaste for Adults 75ml has no fixed shelf life stated here because it depends on the production batch and storage conditions. Ask us for the expiry date of the batch in your quotation and keep stock away from heat and direct sunlight.

Who supplies the Toothpaste for Adults 75ml?
The Toothpaste for Adults 75ml is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India. The company sources it for institutional and humanitarian hygiene orders and quotes for delivery in India and international markets via the contact page.

Request a Quote

Share the quantity, flavour choice and delivery location for the Toothpaste for Adults 75ml on the contact page, or add it to the enquiry cart.

Last updated: 24 September 2026

Toothbrush for Children (Product Code: SLE/SAH/06) is a soft, small-size toothbrush used for children's daily tooth brushing at home, in schools and in hygiene kits for families. Each brush is individually wrapped, and its bristles are specified to be free of sharp or jagged edges and not to fall out with normal use. It is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India.

Key Details

What Is the Children's Toothbrush Used For?

A child's mouth needs a brush with a smaller head and gentler bristles than an adult's, so it can reach back teeth comfortably without hurting the gums. This soft, small-size brush is meant for that everyday job and is a standard item in school health programmes, boarding-school stores and emergency family kits.

Individual wrapping keeps each brush clean until it is handed over, which matters when brushes are distributed in bulk. After brushing, children should rinse the brush and let it air-dry upright, and it is worth replacing any brush whose bristles have splayed. Pair it with a children's toothpaste so the set suits young users from the start.

What to Specify When Ordering

• Number of children's toothbrushes.
• Whether adult toothbrushes are needed for the same family kits.
• Whether toothpaste for children should be included in the quotation.

Supplier

Jain Scientific Equipments Private Limited, which does business as ScienceLab, supplies this children's toothbrush from Ambala, Haryana, India. It sources oral-care and grooming items for schools, child-focused NGOs and humanitarian programmes, and quotes them as single items or as part of full hygiene kits for India and international markets. Read about the company on the ScienceLab profile page.

Related Water, Sanitation & Hygiene Supplies

Useful companions for a child's hygiene kit:

• Toothpaste for Children 75ml — neutral-flavour, non-fluoride paste made for children.
• Toothbrush for Adult — the adult-size, medium-hardness brush for parents and older children.
• Child Potty — a sanitation item often supplied with young children's kits.
• Soap Toilet Bar Approx. 100-110g Wrapped — for teaching handwashing alongside tooth brushing.

The full range is listed under Water, Sanitation & Hygiene Supplies.

Frequently Asked Questions

How soft are the bristles of the Toothbrush for Children?
The Toothbrush for Children has soft bristles, specified to be free of sharp or jagged edges and endpoints. Soft bristles are generally recommended for children because they clean the teeth while being gentle on young gums.

Is the Toothbrush for Children individually wrapped?
Yes, every Toothbrush for Children is individually wrapped. This keeps each brush clean during storage and bulk distribution and lets schools or programmes hand out one sealed brush per child.

Will the bristles of the Toothbrush for Children come loose?
The Toothbrush for Children is specified so that its bristles do not fall out with normal use, and all of its components are required to be safe for use. Replace any brush once its bristles become worn or splayed.

What age group is the Toothbrush for Children meant for?
The Toothbrush for Children is a small-size brush suitable for children; no specific age range is stated. For teenagers or adults, the Toothbrush for Adult in the same range, with medium-hardness bristles, is the matching choice.

Who supplies the Toothbrush for Children?
The Toothbrush for Children is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India, which sources it for schools and hygiene programmes. Bulk quantities for India and international markets are quoted through the contact page.

Request a Quote

Tell us how many Toothbrush for Children units you need and where they should be delivered using the contact page, or add the item to the enquiry cart with toothpaste and other kit items.

Last updated: 24 September 2026

Toothbrush for Adult (Product Code: SLE/SAH/07) is an adult-size toothbrush with medium-hardness bristles used for everyday oral hygiene in households, hostels, workforce camps and relief hygiene kits. It is individually wrapped, and its bristles are specified to be free of sharp or jagged edges and to stay in place with normal use. It is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India.

Key Details

What Is the Adult Toothbrush Used For?

This brush is the adult counterpart in a hygiene kit: an adult-size handle and head for daily cleaning of teeth, with medium-hardness bristles that give a firmer scrub than a child's soft brush. Organisations issuing personal kits to workers, hostel residents or displaced families typically include one brush per adult together with toothpaste and soap.

Medium bristles suit most adults, but users should still brush with gentle pressure to protect the gums. Because each brush comes individually wrapped, stock can be stored and distributed without the brushes touching one another, and each recipient opens a clean brush. Rinse after use, store upright to dry and replace the brush when bristles start to fray.

What to Specify When Ordering

• Number of adult toothbrushes (commonly one per adult in the kit).
• Whether soft children's toothbrushes are needed for the same distribution.
• Whether adult toothpaste should be quoted with the brushes.

Supplier

Supply of this adult toothbrush comes from Jain Scientific Equipments Private Limited, trading as ScienceLab, based in Ambala, Haryana, India. The company sources oral-care items for employers, hostels, NGOs and humanitarian agencies, and handles quotation, packing and dispatch of mixed hygiene orders within India and to international markets. Company details are on the ScienceLab profile page.

Related Water, Sanitation & Hygiene Supplies

Other items for an adult personal hygiene kit:

• Toothpaste for Adults 75ml — non-fluoride paste, unflavoured or peppermint.
• Toothbrush for Children — soft, small-size brushes for children in the household.
• Soap Box Plastic — a two-piece case for carrying soap in a personal kit.
• Nail Clipper Metal Medium Size — a metal grooming tool for the same kit.

More products are in Water, Sanitation & Hygiene Supplies.

Frequently Asked Questions

What bristle hardness does the Toothbrush for Adult have?
The Toothbrush for Adult has medium-hardness bristles, a common choice for adults who want a firmer clean than a soft brush gives. The bristle ends are specified to be free of sharp or jagged edges and endpoints.

Is the Toothbrush for Adult packed individually?
Yes, each Toothbrush for Adult is individually wrapped, so brushes stay clean in storage and can be handed out one per person. This makes it practical for hostels, employers and relief agencies that issue personal hygiene kits.

Are the Toothbrush for Adult components safe?
All components of the Toothbrush for Adult are specified as safe for use, and its bristles must not fall out with normal use. If your programme needs material details in writing, ask us through the contact page before ordering.

How is the Toothbrush for Adult different from the Toothbrush for Children?
The Toothbrush for Adult is adult size with medium-hardness bristles, while the Toothbrush for Children is small size with soft bristles. Both are individually wrapped, so they can be ordered together for family hygiene kits.

Who supplies the Toothbrush for Adult?
The Toothbrush for Adult is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India. The company sources the brushes for institutional and humanitarian buyers and quotes bulk quantities for India and international markets.

Request a Quote

Send the number of Toothbrush for Adult units and your delivery location through the contact page, or add the brush to the enquiry cart along with toothpaste and soap.

Last updated: 24 September 2026

Soap Box Plastic (Product Code: SLE/SAH/08) is a two-piece plastic soap box used to store and carry a bar of soap in personal hygiene kits, hostels, bathrooms and field camps. It is made of boilable plastic, so the box can be cleaned in boiling water when kits are reused or shared. It is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India.

Key Details

What Is the Plastic Soap Box Used For?

A soap box keeps a bar of soap clean between uses and stops it picking up dirt when it is carried in a bag or left on a shelf. The two-piece design separates into a base and a cover, so the user can open it at the wash point, use the soap and close it again for storage or travel. It is a small but practical item in family hygiene kits, school boarding supplies and camp distributions where people share washing areas.

Because the plastic is boilable, the box can be cleaned thoroughly in hot water before being reissued. Let the soap drain and the box dry with its cover open when possible, so the bar does not sit in water and soften.

What to Specify When Ordering

• Number of soap boxes (usually one per soap bar or per kit).
• Whether soap bars should be quoted with the boxes.
• Any colour or packing preference for your distribution, so we can check availability.

Supplier

Jain Scientific Equipments Private Limited, trading as ScienceLab, supplies this plastic soap box from Ambala, Haryana, India. The company sources small hygiene accessories alongside soap, toothpaste and grooming items, so buyers can place one order for a complete kit. Export orders are documented under Importer-Exporter Code AAECJ8618A (DGFT), and the company's GST registration is 06AAECJ8618A1ZT. More on the ScienceLab profile page.

Related Water, Sanitation & Hygiene Supplies

Items that pair naturally with a soap box:

• Soap Toilet Bar Approx. 100-110g Wrapped — the perfume-free bar soap the box is meant to hold.
• Toothbrush for Adult — another everyday item in a personal kit.
• Multipurpose Cloth Cotton 1x1.5m — a cotton cloth that can double as a towel.
• Hand Wash Station — a shared handwashing point for schools and camps.

Find more in Water, Sanitation & Hygiene Supplies.

Frequently Asked Questions

What is the Soap Box Plastic made of?
The Soap Box Plastic is made of boilable plastic, meaning it can be cleaned in boiling water. That makes it easier to sanitise boxes that are collected and reissued, or used in shared washing facilities.

How does the Soap Box Plastic open and close?
The Soap Box Plastic is a two-piece box: one part holds the soap and the other closes over it as a cover. The two pieces separate completely, which also makes both parts easy to wash and dry.

What size of soap fits the Soap Box Plastic?
The dimensions of the Soap Box Plastic are not listed, so please check fit before ordering in bulk. If you plan to pair it with the wrapped toilet soap bar from the same range, ask us through the contact page and we will confirm.

How should the Soap Box Plastic be cleaned?
The Soap Box Plastic can be washed with soap and water or cleaned in boiling water, as it is made of boilable plastic. Separate the two pieces first, then let them dry fully before putting soap back in.

Who supplies the Soap Box Plastic?
The Soap Box Plastic is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India. The company sources it for hygiene kits and institutional orders and quotes quantities for delivery in India and international markets.

Request a Quote

For prices on the Soap Box Plastic, send your quantity and destination through the contact page or add it to the enquiry cart together with soap bars.

Last updated: 24 September 2026

Nail Clipper Metal Medium Size (Product Code: SLE/SAH/09) is a metal nail clipper, approximately 60-70 mm long, used for trimming fingernails and toenails as part of personal hygiene at home, in hostels and in hygiene kits. It is made in stainless steel or chromium-plated metal, with an ergonomic design and a smooth cutting action. It is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India.

Specifications

What Is the Metal Nail Clipper Used For?

Short, clean nails are a simple barrier against dirt collecting under the nail, which is why nail care is taught alongside handwashing in school health lessons and included in many family hygiene kits. This medium-size clipper, around 60-70 mm long, is large enough for adults to grip firmly yet compact enough to store in a small personal kit.

To use it, trim nails straight across in small cuts rather than one large snip, then smooth any rough edges. Clean the clipper with soap and water after each use and dry it before storing; when a clipper is shared within a household, wiping the blades between users is a sensible habit. Adults should trim young children's nails for them.

What to Specify When Ordering

• Number of nail clippers.
• Preferred finish, stainless steel or chromium plated, if your programme specifies one.
• Whether other personal hygiene items should be quoted as part of the same kit.

Supplier

Jain Scientific Equipments Private Limited, which trades as ScienceLab, supplies this metal nail clipper from Ambala, Haryana, India. The company sources grooming and personal-care items for institutions, NGOs and humanitarian kit packers and lists them with soap, toothbrushes and toothpaste so the whole kit can be quoted in one go for India and international markets. See the ScienceLab profile page for company background.

Related Water, Sanitation & Hygiene Supplies

Personal hygiene items commonly packed with a nail clipper:

• Soap Toilet Bar Approx. 100-110g Wrapped — for washing hands and nails after trimming.
• Toothbrush for Adult — the individually wrapped adult brush for the same kit.
• Soap Box Plastic — a two-piece case to keep soap clean in a personal kit.
• Reusable Menstrual Set — washable pads often included in kits for women and girls.

Browse Water, Sanitation & Hygiene Supplies for the rest of the range.

Frequently Asked Questions

How long is the Nail Clipper Metal Medium Size?
The Nail Clipper Metal Medium Size is approximately 60-70 mm long. This medium size gives adults a comfortable grip while remaining small enough to fit into a compact personal hygiene kit or toiletry pouch.

What metal is the Nail Clipper Metal Medium Size made from?
The Nail Clipper Metal Medium Size is made in stainless steel or chromium-plated metal. If your tender specifies one of these finishes, mention it in your enquiry so we can confirm which version will be supplied.

Is the Nail Clipper Metal Medium Size easy to use?
Yes, the Nail Clipper Metal Medium Size has an ergonomic design and a smooth action, so the lever presses down evenly and the blades close cleanly. Trim nails straight across in small cuts for the neatest result.

How should the Nail Clipper Metal Medium Size be cleaned?
Clean the Nail Clipper Metal Medium Size with soap and water after use, remove any nail fragments from between the blades and dry it completely before storage, which helps keep the metal finish in good condition.

Who supplies the Nail Clipper Metal Medium Size?
The Nail Clipper Metal Medium Size is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India, which sources it for hygiene kits and institutional buyers. Quotations for India and international markets are available through the contact page.

Request a Quote

Send your required quantity of the Nail Clipper Metal Medium Size and the delivery location via the contact page, or add it to the enquiry cart with other kit items.

Last updated: 24 September 2026

Laundry Detergent/Washing Powder, 1.5kg (Product Code: SLE/SAH/10) is a concentrated washing powder used for hand washing clothes and household textiles in homes, hostels, camps and emergency relief settings. It comes in a 1.5 kg pack that is specified to be water resistant, so it can be stored and distributed in the varied climatic conditions of disaster response. It is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India.

Specifications

What Is the Laundry Washing Powder Used For?

Clean clothing, bedding and cloth items are part of basic hygiene, especially where families live in crowded shelters or have limited water. This concentrated powder is intended for washing by hand in a bucket or basin, which is how most laundry is done in relief camps, rural homes and many hostels. A concentrated powder means a smaller amount is needed per wash, which helps a single 1.5 kg pack last longer.

The water-resistant pack protects the powder from rain and humidity during transport and storage, so it does not cake before it reaches users. Dissolve the powder fully in water before adding clothes, rinse well and keep the pack closed and off the ground between uses. Wear gloves if you have sensitive skin or wash for long periods.

What to Specify When Ordering

• Number of 1.5 kg packs.
• Preferred water-resistant packaging type, if your programme requires one: plastic bag, carton with plastic insert or laminated carton.
• Whether soap bars or other hygiene items should be quoted for the same distribution.

Supplier

This washing powder is supplied by Jain Scientific Equipments Private Limited, known by its trading name ScienceLab, from Ambala, Haryana, India. The company sources laundry and cleaning consumables for relief agencies, NGOs, hostels and institutions, and can include them in consolidated hygiene-kit shipments to buyers in India and international markets. Company background is on the ScienceLab profile page.

Related Water, Sanitation & Hygiene Supplies

Other items often distributed with laundry powder:

• Soap Toilet Bar Approx. 100-110g Wrapped — bar soap for personal washing in the same kit.
• Reusable Menstrual Set — washable pads that need regular laundering with detergent.
• Multipurpose Cloth Cotton 1x1.5m — a washable cotton cloth for household use.
• Garbage Bags, 100 liters — for collecting household waste in shelters and camps.

See the whole range in Water, Sanitation & Hygiene Supplies.

Frequently Asked Questions

What pack size is the Laundry Detergent/Washing Powder, 1.5kg?
The Laundry Detergent/Washing Powder, 1.5kg comes in a 1.5 kg pack of concentrated washing powder. Quantities are quoted by the number of packs, so tell us how many households or users a distribution will cover.

Is the Laundry Detergent/Washing Powder, 1.5kg for machines or hand washing?
The Laundry Detergent/Washing Powder, 1.5kg is a concentrated powder intended for hand washing of laundry. That suits relief camps, rural households and hostels where clothes are washed in buckets or basins rather than machines.

Why is the Laundry Detergent/Washing Powder, 1.5kg pack water resistant?
The Laundry Detergent/Washing Powder, 1.5kg pack is specified as water resistant because it may be stored and distributed in different climatic and disaster situations. Acceptable packs are a sturdy plastic bag, a carton with a plastic bag insert or a plastic-laminated carton.

What is the shelf life of the Laundry Detergent/Washing Powder, 1.5kg?
Shelf life of the Laundry Detergent/Washing Powder, 1.5kg depends on the batch and on storage conditions, so no fixed period is stated. Ask us for the expiry date of the batch in your quotation and keep packs sealed in a dry place.

Who supplies the Laundry Detergent/Washing Powder, 1.5kg?
The Laundry Detergent/Washing Powder, 1.5kg is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India, which sources it for relief and institutional orders. Request bulk quotations for India and international markets through the contact page.

Request a Quote

To get a price for the Laundry Detergent/Washing Powder, 1.5kg, send the number of packs, any packaging preference and the delivery destination through the contact page, or add it to the enquiry cart.

Last updated: 24 September 2026

Garbage Bags, 100 liters (Product Code: SLE/SAH/11) is a black plastic refuse bag with a 100-litre capacity, used to collect and carry household, school and camp waste to disposal points. Each bag closes with a drawstring around the top, is made from material not less than 40 micron thick and can carry up to 50 kg. It is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India.

Specifications

What Is the 100 Litre Garbage Bag Used For?

Good waste handling is part of sanitation: rubbish left in the open attracts flies and rodents and can block drains. A 100-litre bag fits large bins in classrooms, corridors, canteens, offices and shelter sites, and the drawstring lets whoever empties the bin close it quickly and carry it by the gathered top without touching the contents.

With material at least 40 micron thick and a load rating of up to 50 kg, the bag is meant for everyday mixed waste and heavier loads from clean-up campaigns. Do not overfill beyond the point where the drawstring closes, keep sharp objects out or wrap them first, and store unused rolls or packs away from heat and direct sunlight.

What to Specify When Ordering

• Number of bags required.
• Any minimum thickness above 40 micron that your tender requires, so it can be confirmed before quoting.
• Whether cleaning items from the same range should be quoted together.

Supplier

Jain Scientific Equipments Private Limited, the company that trades as ScienceLab, supplies these garbage bags from Ambala, Haryana, India. It sources waste-handling and cleaning consumables for schools, hostels, offices, municipal bodies and relief operations, and co-ordinates packing and dispatch for buyers in India and international markets. Company information is on the ScienceLab profile page.

Related Water, Sanitation & Hygiene Supplies

Cleaning and sanitation products that work alongside refuse bags:

• Mop Bucket with Strainer — for floor cleaning in the same rooms where bins are emptied.
• Universal Disinfectant Spray — for wiping down bins and waste areas.
• Classroom Cleaning & Sanitization Kit — a cleaning kit for schools.
• Sprayer Compression Type 11.35 Litres — for spraying cleaning solutions over larger areas.

More items are listed in Water, Sanitation & Hygiene Supplies.

Frequently Asked Questions

What is the capacity of the Garbage Bags, 100 liters?
Each of the Garbage Bags, 100 liters holds 100 litres, a size that suits large bins in schools, offices, canteens and camps. The bags are black, made of strong, durable plastic and close with a drawstring around the top.

How much weight can the Garbage Bags, 100 liters carry?
The Garbage Bags, 100 liters are specified to carry weight up to 50 kg. Close the drawstring fully and lift from the gathered top; avoid putting sharp or jagged items straight into the bag without wrapping them.

How thick are the Garbage Bags, 100 liters?
The material of the Garbage Bags, 100 liters is not less than 40 micron thick. If your organisation needs a higher minimum, state it in your enquiry through the contact page so it can be checked before a quotation is issued.

How do the Garbage Bags, 100 liters close?
The Garbage Bags, 100 liters have a drawstring around the top. Pulling the string gathers the opening shut, so the bag can be tied and carried without handling the waste inside, which also helps keep smells and flies contained.

Who supplies the Garbage Bags, 100 liters?
The Garbage Bags, 100 liters are supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India. The company sources them for institutional, municipal and relief buyers and quotes bulk quantities for India and international markets.

Request a Quote

Send the number of Garbage Bags, 100 liters you need and the delivery destination through the contact page, or add them to the enquiry cart with other cleaning supplies.

Last updated: 24 September 2026

Pan and "P" Trap For Squatting Plate (Product Code: SLE/SAH/12) is a moulded latrine pan with a P-shaped trap, used to fit a 120 x 80 cm squatting plate when building or upgrading latrines for schools, communities and emergency camps. The pan is moulded in polypropylene (PP) and bolts to the underside of the plate, while the HDPE trap is fixed to the pan with the adhesive provided. It is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India.

Specifications

What Is the Latrine Pan and P Trap Used For?

A squatting plate on its own leaves an open drop hole; adding a pan and trap turns it into a flushed latrine that is cleaner to use and easier to keep free of smells. The pan guides waste from the plate opening into the trap, and a trap of this shape generally holds a small water seal after flushing, which helps stop odours and flies from coming back up from the pit or drain.

Installation is simple: the PP pan is bolted to the underside of the 120 x 80 cm plate with the supplied fasteners, and the HDPE trap is then bonded to the pan outlet with the supplied adhesive. Let the adhesive cure as directed before first use, and keep a container of water near the latrine so users can flush after every visit.

What to Specify When Ordering

• Trap type: this "P" trap version, or the goose neck trap version listed separately.
• Confirmation that your squatting plates are the 120 x 80 cm size.
• Number of pan-and-trap sets (one per squatting plate).
• Whether squatting plates, slab moulds or latrine superstructures should be quoted together.

Supplier

This pan and trap set is supplied by Jain Scientific Equipments Private Limited, whose trading name is ScienceLab, from Ambala, Haryana, India. The company sources sanitation hardware for NGOs, relief agencies, contractors and school building programmes, and can quote the pan together with plates and superstructures from the same range for India and international markets. Buyers adding the company to an approved-vendor list can use GSTIN 06AAECJ8618A1ZT and Legal Entity Identifier 3358004HRD1JIVXKYX49. See the ScienceLab profile page.

Related Water, Sanitation & Hygiene Supplies

Latrine components that are planned together with this pan and trap:

• Squatting Plate, Plastic, W/o pan, 120x80cm — the plastic plate this pan is sized to fit.
• Pan and Goose Neck Trap — the alternative trap shape for the same plate.
• Mould Plastic for Concrete Latrine Slab — for casting concrete latrine slabs on site.
• Latrine Superstructure Single Cubicle — the enclosure that completes a single latrine.

View the full Water, Sanitation & Hygiene Supplies category.

Frequently Asked Questions

Which squatting plate does the Pan and "P" Trap For Squatting Plate fit?
The Pan and "P" Trap For Squatting Plate is made for a squatting plate of 120 x 80 cm. The pan bolts to the underside of the plate, so check that your plates match this size before ordering; the plastic 120x80cm plate in the same range is the intended partner.

What materials are used in the Pan and "P" Trap For Squatting Plate?
In the Pan and "P" Trap For Squatting Plate, the pan is moulded in PP (polypropylene) and the trap is moulded in HDPE. Both are plastics commonly used in sanitation fittings because they do not rust and are easy to clean.

How is the Pan and "P" Trap For Squatting Plate installed?
To install the Pan and "P" Trap For Squatting Plate, bolt the pan to the underside of the squatting plate with the fasteners provided, then fix the trap to the pan with the adhesive provided. Allow the adhesive to set before the latrine is used.

What is the difference between the P trap and goose neck trap versions?
Both trap types for the Pan and "P" Trap For Squatting Plate range are moulded in HDPE and fit the same pan; they differ in the shape of the trap. This listing is the P trap version, and the goose neck version is available as a separate item. Ask us which suits your pit or drain layout.

Who supplies the Pan and "P" Trap For Squatting Plate?
The Pan and "P" Trap For Squatting Plate is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India. The company sources it for sanitation projects and quotes bulk quantities for India and international markets through the contact page.

Request a Quote

Send the number of Pan and "P" Trap For Squatting Plate sets, the trap type and your delivery location through the contact page, or add the item to the enquiry cart with plates and superstructures.

Last updated: 24 September 2026

Pan and Goose Neck Trap (Product Code: SLE/SAH/13) is a sanitation fitting set, made up of a latrine pan and a goose neck water-seal trap, used to add a pan and water seal beneath a squatting plate in latrine installations. It is intended for squatting plates of 120 cm x 80 cm, so sanitation teams and site engineers can match it directly to that plate size. The set is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India, a laboratory equipment supplier in India that also sources water, sanitation and hygiene items.

Key Details

What Is the Pan and Goose Neck Trap Used For?

A goose neck trap is a curved section below the pan that holds back a small amount of water after each use. That water seal separates the user from the pit or drain below, which helps limit odour and keeps flies from moving freely between the pit and the cubicle. Fitting a pan and trap under a squatting plate turns a simple direct-drop hole into a water-sealed latrine that is flushed by pouring in a little water.

The set is chosen for latrines built on 120 cm x 80 cm squatting plates, such as those used in camps, schools and community sanitation projects. When installing, keep the joint between plate and pan firm and leak-free, and make sure the trap is refilled with water after cleaning so the seal is never left dry. Avoid putting stones, rags or other solid objects into the pan, as they can block the bend.

What to Specify When Ordering

• Number of sets — usually one for each 120 cm x 80 cm squatting plate being fitted.
• Confirmation that your squatting plates measure 120 cm x 80 cm.
• Whether a goose neck trap or a P trap arrangement suits your drain layout.
• Delivery destination, within India or for export.

Supplier

This set is supplied by Jain Scientific Equipments Private Limited, which trades as ScienceLab and is based in Ambala, Haryana. Alongside educational laboratory equipment, the company sources sanitation fittings such as this pan and trap for institutions, project buyers and dealers in India and international markets. Read more about the company on the ScienceLab company profile.

Related Water, Sanitation & Hygiene Supplies

These items are used alongside the pan and goose neck trap when building or upgrading a latrine:

• Squatting Plate, Plastic, W/o pan, 120x80cm — a plate in the 120 x 80 cm size this set is intended for.
• Pan and "P" Trap For Squatting Plate — the alternative trap shape if a P trap suits your drain layout better.
• Latrine Superstructure Single Cubicle — a cabin kit to enclose a single latrine.
• Latrine Add-On Child and Disabled People — a raised-seat kit that makes the latrine easier to use for children and people with disabilities.

Browse the complete Water, Sanitation & Hygiene Supplies range for latrine parts, handwashing and cleaning items.

Frequently Asked Questions

What is included in the Pan and Goose Neck Trap set?
The Pan and Goose Neck Trap (SLE/SAH/13) is listed as a set made up of a latrine pan and a goose neck trap. Fixing hardware, sealant and the squatting plate itself are not listed as part of the set, so please confirm the exact contents with us when you request a quotation.

Which squatting plate does the Pan and Goose Neck Trap fit?
The Pan and Goose Neck Trap is intended for squatting plates of 120 cm x 80 cm. If your plates are a different size or come from another source, send us their dimensions and drop-hole details before ordering so the fit can be checked.

What does the goose neck trap do?
The goose neck trap in this pan set holds a small volume of water in its curved section after flushing. This water seal separates the latrine user from the pit or drain below and helps reduce odour and fly access, provided the trap is kept topped up with water.

What material is the Pan and Goose Neck Trap made of?
Our listing for the Pan and Goose Neck Trap does not state its material, wall thickness or water-seal depth. Please ask us through the contact page and we will share the details of the set offered before you confirm an order.

Who supplies the Pan and Goose Neck Trap?
The Pan and Goose Neck Trap is supplied by Jain Scientific Equipments Pvt Ltd, trading as ScienceLab, from Ambala, Haryana, India. The company sources sanitation items like this set for institutions, project buyers and dealers in India and international markets.

What should a quotation request for the Pan and Goose Neck Trap include?
For a Pan and Goose Neck Trap quotation, share the number of sets, confirmation of your 120 cm x 80 cm plate size, any preference between goose neck and P trap designs, and the delivery destination. Adding related latrine items to the same enquiry lets them be quoted together.

Request a Quote

To order the Pan and Goose Neck Trap, send your quantity and delivery location through the contact page, or add it to the enquiry cart together with other water, sanitation and hygiene supplies.

Last updated: 24 September 2026

Squatting Plate, Plastic, W/o pan, 120x80cm (Product Code: SLE/SAH/14) is a self-supporting plastic direct-drop latrine slab used to cover latrine pits and trenches in emergency sanitation situations. Moulded in LLDPE with foot rests, a keyhole-shaped drop hole and an attached HDPE keyhole cover, it comes without a pan but is prepared for later water-seal installation. It is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India, a lab equipment exporter that also sources emergency sanitation items.

Specifications

What Is the Plastic Squatting Plate Used For?

In the first phase of an emergency response, this plate is laid over a latrine pit or trench to give people a safe, cleanable squatting surface without waiting for concrete slabs to be cast and cured. The foot rests show users where to stand, the keyhole drop hole is sized with small children in mind, and the attached cover can be closed between uses to keep flies and odour down.

For installation, rest the plate on firm ground at both ends and drive the four supplied metal pegs through the corner holes so it cannot shift. Because the underside is prepared for a pan and water-seal trap, the same plate can later be upgraded from direct drop to a water-sealed latrine. Wash the surface towards the drop hole, where the built-in slope carries water and dirt away.

What to Specify When Ordering

• Number of plates needed for the pits or trenches on your site.
• Whether you also need a pan with P trap or goose neck trap now or later.
• Superstructure required — single-cubicle or double-cubicle kits.
• Whether some latrines need an accessibility add-on for children and people with disabilities.

Supplier

Jain Scientific Equipments Private Limited, trading as ScienceLab from Ambala, Haryana, supplies this squatting plate as part of its water, sanitation and hygiene range. Emergency programmes, institutions and dealers in India and international markets can source the plate together with pans, traps and cabin kits from one supplier. The ScienceLab company profile explains who we are and how we work.

Related Water, Sanitation & Hygiene Supplies

Items that complete a latrine built on this 120 x 80 cm plate:

• Pan and "P" Trap For Squatting Plate — converts the direct-drop hole into a water-sealed latrine.
• Pan and Goose Neck Trap — a pan and trap set intended for 120 cm x 80 cm plates.
• Latrine Superstructure Single Cubicle — a lockable cabin kit for one plate.
• Latrine Add-On Child and Disabled People — an elevated seat kit that fits the same plate size.
• Mould Plastic for Concrete Latrine Slab — for casting concrete slabs locally once the site is established.

See every item in the Water, Sanitation & Hygiene Supplies category.

Frequently Asked Questions

Does the Squatting Plate, Plastic, W/o pan, 120x80cm come with a pan?
No. The Squatting Plate, Plastic, W/o pan, 120x80cm is supplied without a pan. Its underside has an arrangement for bolting or otherwise securely fastening a pan/bowl and water-seal trap if required, so a pan and trap can be ordered separately.

How much weight can the plastic squatting plate support?
This 120 x 80 cm plastic squatting plate is specified to securely support a minimum of 150 kg at the centre, with its two ends resting on no more than 100 mm of firm support each, taking tropical ambient temperatures and direct sunshine into account.

Are anchor pegs included with the squatting plate?
Yes. Four metal anchor/fixation pegs measuring 8 mm x 275 mm are included with the Squatting Plate, Plastic, W/o pan, 120x80cm. They pass through holes in the four corners with a water-tight fit, and a storage arrangement for them on the underside is suggested.

Is the drop hole of the squatting plate safe for small children?
The keyhole-shaped drop hole of this plastic squatting plate is dimensioned so that a small child cannot pass through it, and the attached HDPE keyhole cover can be closed when the latrine is not in use. Supervising young children in latrines remains good practice.

What material is the plastic squatting plate made of?
The squatting plate is moulded in LLDPE, and its keyhole cover in HDPE. The specification allows other materials as long as they are plastic based, light, sturdy and easy to clean, so ask us to confirm the material of the plates quoted to you.

Who supplies the Squatting Plate, Plastic, W/o pan, 120x80cm?
Jain Scientific Equipments Pvt Ltd, trading as ScienceLab, Ambala, India, supplies this plastic squatting plate to emergency programmes, institutions and dealers. Send quantity and destination through our contact page to receive a quotation.

Request a Quote

Tell us how many plates you need and whether pans, traps or superstructures should be included via the contact page, or place the item in the enquiry cart with the rest of your sanitation list.

Last updated: 24 September 2026

Mould Plastic for Concrete Latrine Slab (Product Code: SLE/SAH/15) is a polymeric form used to cast concrete latrine slabs on site for household, school and community sanitation. Made of UV-protected, impact-resistant polymer 4 mm thick with a very smooth finish, it produces a slab of 60 x 60 cm, around 8 cm thick, with two raised foot rests and a child-safe drop hole. It is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India, whose scientific equipment bulk supply work extends to sanitation items like this mould.

Specifications

What Is the Latrine Slab Mould Used For?

The mould lets sanitation teams, masons and community groups make concrete latrine slabs close to where they are needed, using locally available cement and aggregate instead of transporting finished slabs. Concrete is placed in the form, compacted and left to cure; once released, the slab already has its foot rests, drop hole and cleaning slope moulded in, so every slab from the same mould comes out consistent.

Because a mould is used again and again, durability matters: this one is UV protected and built to stand rough field handling. Practical tips: work on level ground, clean the form after every casting so the smooth finish transfers to the next slab, and follow local engineering guidance on concrete mix, any reinforcement and curing time before slabs are placed over pits.

What to Specify When Ordering

• Number of moulds, based on how many slabs your teams plan to cast at the same time.
• Confirmation that a 60 x 60 cm slab, around 8 cm thick, suits your pit openings.
• Whether ready-made plastic squatting plates are also needed for immediate use while slabs cure.

Supplier

The mould is supplied by Jain Scientific Equipments Private Limited, the company behind the ScienceLab name, from Ambala in Haryana. Sanitation programmes, contractors and dealers can source it alongside other latrine components and hygiene supplies, for delivery in India and international markets. More about the company is on the ScienceLab profile page.

Related Water, Sanitation & Hygiene Supplies

Other items often ordered with a latrine slab mould:

• Squatting Plate, Plastic, W/o pan, 120x80cm — a ready-made plastic plate for latrines that must open before cast slabs are ready.
• Latrine Superstructure Single Cubicle — a lockable cabin kit designed for standard 120 x 80 cm plates.
• Sprayer Trigger Bottle Handheld 1 Liter — for disinfecting latrine slab surfaces during routine cleaning.
• Child Potty — for young children who are not yet using a latrine.

Explore the full Water, Sanitation & Hygiene Supplies range.

Frequently Asked Questions

What size slab does the Mould Plastic for Concrete Latrine Slab produce?
The Mould Plastic for Concrete Latrine Slab produces a finished slab of 60 x 60 cm with a thickness of around 8 cm. Each slab has two raised foot rests, a drop hole dimensioned to be safe for small children and surfaces that slope towards the hole for easy cleaning.

How durable is the latrine slab mould?
The latrine slab mould is made of high-quality polymers 4 mm thick that are UV protected and impact resistant, and it is designed to stand rough handling under field conditions. The number of castings per mould is not stated, so ask us if you need that for planning.

Is concrete or reinforcement included with the mould?
No. The Mould Plastic for Concrete Latrine Slab is listed as the plastic form only. Cement, aggregate, any reinforcement and a release agent are sourced locally, and the concrete mix should follow your engineering team's guidance for latrine slabs.

Why cast concrete slabs instead of using plastic plates?
Casting slabs with this mould lets local teams produce latrine slabs near the site from local materials once a programme is established, while plastic squatting plates are quicker to deploy in the first days. Many buyers use both, depending on the stage of the response.

Who supplies the Mould Plastic for Concrete Latrine Slab?
Jain Scientific Equipments Pvt Ltd, trading as ScienceLab from Ambala, Haryana, India, supplies the Mould Plastic for Concrete Latrine Slab to sanitation programmes, contractors and dealers in India and international markets.

What information is needed for a quotation?
For a quotation on the latrine slab mould, send the number of moulds, the delivery destination and any related items such as plastic squatting plates or superstructure kits through the contact page, so everything can be quoted together.

Request a Quote

Request pricing for the Mould Plastic for Concrete Latrine Slab through the contact page, or add it to the enquiry cart with other sanitation items on your list.

Last updated: 24 September 2026

Latrine Superstructure Single Cubicle (Product Code: SLE/SAH/16) is a complete latrine cabin kit used to enclose one latrine stance built on a standard 120 cm x 80 cm squatting plate in emergency and institutional sanitation. The kit forms a superstructure with a lockable door, roof/cover and natural ventilation, and needs no materials sourced in the country for its initial installation. It is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India, a supplier of scientific & laboratory instruments that also sources emergency sanitation kits.

Specifications

What Is the Single-Cubicle Latrine Superstructure Used For?

A latrine is only used consistently when people feel safe and have privacy. This kit turns an open squatting plate into an enclosed cabin: the walls and roof give shelter from sun and rain, the lockable door gives users privacy and security, and natural ventilation lets air move through the cubicle to reduce odour and humidity.

The single-cabin format suits a family latrine, a stand-alone latrine at a health or feeding centre, or a row of stances over a trench where each cabin is set up separately. Assemble it directly over the 120 x 80 cm plate on firm ground, check that the door locks and closes properly, and include the cabin in routine cleaning, since it is built to tolerate manual cleaning.

What to Specify When Ordering

• Number of cabins — one kit per latrine stance to be enclosed.
• Whether squatting plates of 120 cm x 80 cm are needed with the kits.
• Single-cubicle kits, double-cubicle kits, or a mix of both.
• Whether any latrines need the add-on kit for children and people with disabilities.

Supplier

Jain Scientific Equipments Private Limited trades as ScienceLab and operates from Ambala, Haryana. The company supplies this cabin kit, together with plates, pans and hygiene items, to emergency programmes, institutions and dealers in India and international markets. For vendor registration, the supplying company is Jain Scientific Equipments Private Limited (CIN U29309HR2020PTC087597, GSTIN 06AAECJ8618A1ZT). Company background is on the ScienceLab profile.

Related Water, Sanitation & Hygiene Supplies

Items that work with the single-cubicle superstructure:

• Latrine Superstructure Double Cubicle — the two-cabin version for blocks of two stances.
• Squatting Plate, Plastic, W/o pan, 120x80cm — a plastic plate in the size this cabin is designed around.
• Latrine Add-On Child and Disabled People — an elevated seat kit to improve access in selected latrines.
• Torch Handheld Self-Powered — a wind-up torch that helps users reach the latrine safely after dark.

View the whole Water, Sanitation & Hygiene Supplies category.

Frequently Asked Questions

What is included in the Latrine Superstructure Single Cubicle kit?
The Latrine Superstructure Single Cubicle kit forms one cabin with a lockable door, roof/cover and natural ventilation. It is described as complete and ready to install. The squatting plate is not listed as part of the kit, so order plates separately if you need them.

Which squatting plate does the single-cubicle superstructure fit?
The Latrine Superstructure Single Cubicle is designed for use with a standard squatting plate of 120 cm x 80 cm. If your site uses another slab size, send us its dimensions before ordering so compatibility can be discussed.

Can the single-cubicle superstructure be used on trench latrines?
Yes. The Latrine Superstructure Single Cubicle is intended for deployment with trench latrine installations as well as with single slabs. Order one kit for each stance to be enclosed, or use the double-cubicle kit where stances are built in pairs.

How does the cabin kit cope with weather?
The single-cubicle cabin is designed to be lightweight yet rigid, climatically stable and resistant to heat, wind (including stronger windy conditions), dust, rain and manual cleaning. A specific wind-load rating is not stated, so ask us if your site needs one.

Does installation need any local materials?
No. The Latrine Superstructure Single Cubicle kit is meant to need no materials sourced in the country for its initial installation. Its design may allow later repairs with locally available materials, which helps keep latrines in use over a longer period.

Who supplies the Latrine Superstructure Single Cubicle?
Jain Scientific Equipments Pvt Ltd, trading as ScienceLab from Ambala, Haryana, India, supplies the Latrine Superstructure Single Cubicle to programmes, institutions and dealers. Share quantity and destination on the contact page for a quotation.

Request a Quote

Send the number of cabins, plate requirements and delivery destination through the contact page, or add this kit to the enquiry cart with your other sanitation items.

Last updated: 24 September 2026

Latrine Superstructure Double Cubicle (Product Code: SLE/SAH/17) is a latrine cabin kit used to build a block of two latrine stances over standard 120 cm x 80 cm squatting plates in emergency and communal sanitation. It forms a double superstructure with a lockable door for each cabin, a roof/cover and natural ventilation, and is intended for deployment with installations such as trench latrines. It is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India, which also handles school lab equipment bulk supply for institutions.

Specifications

What Is the Double-Cubicle Latrine Superstructure Used For?

Communal sites such as camps, schools, health centres and feeding centres usually need latrines built in groups rather than one by one. This kit encloses two stances in a single block, so teams erect fewer separate structures while every user still gets a private cubicle with its own lockable door. A two-cabin block also makes it easy to allocate cubicles to different user groups where a site plan calls for that.

On a trench latrine, set the block over two 120 x 80 cm plates placed side by side on firm ground, then assemble walls, doors and roof following the kit layout. Keep the ventilation openings clear, check both door locks after assembly, and plan a handwashing point close to the block so users can wash their hands on the way out.

What to Specify When Ordering

• Number of double blocks — each block covers two stances.
• Whether two squatting plates of 120 cm x 80 cm per block are needed as well.
• Any single-cubicle kits for an odd number of stances.
• Whether accessibility add-on kits are needed for selected cubicles.

Supplier

This double-cubicle kit is supplied by Jain Scientific Equipments Private Limited, known by its trading name ScienceLab, of Ambala, Haryana. The company puts together sanitation orders — cabin kits, plates, pans and hygiene consumables — for programmes, schools and dealers in India and international markets. Learn more on the ScienceLab company profile.

Related Water, Sanitation & Hygiene Supplies

Other items for a communal latrine block:

• Latrine Superstructure Single Cubicle — the one-cabin kit for single stances or odd numbers.
• Squatting Plate, Plastic, W/o pan, 120x80cm — plates in the size this block is built around; two are needed per block.
• Latrine Add-On Child and Disabled People — an elevated seat kit for an accessible cubicle.
• Sprayer Trigger Bottle Handheld 1 Liter — a chlorine-appropriate sprayer for cleaning cubicle surfaces.

Browse all Water, Sanitation & Hygiene Supplies.

Frequently Asked Questions

How many latrine stances does the Latrine Superstructure Double Cubicle cover?
The Latrine Superstructure Double Cubicle covers two latrine stances. It forms a block of two cabins, each with a lockable door, plus a roof/cover and natural ventilation, and is intended for standard 120 cm x 80 cm squatting plates.

Are squatting plates included with the double-cubicle kit?
Squatting plates are not listed as part of the Latrine Superstructure Double Cubicle kit. Two plates of 120 cm x 80 cm are needed per block, and they can be ordered from us at the same time if required.

Where is the double-cubicle latrine superstructure typically used?
The double-cubicle latrine superstructure is intended for communal latrines, health centres, feeding centres and schools, typically deployed with trench latrine installations during emergencies, where latrines are built in groups rather than individually.

What is the difference between the single and double cubicle kits?
The Latrine Superstructure Double Cubicle encloses two stances in one block, while the single-cubicle kit encloses one. Both are for 120 cm x 80 cm plates and have lockable doors, roof and ventilation; the double suits communal blocks, the single suits family or stand-alone latrines.

Who supplies the Latrine Superstructure Double Cubicle?
Jain Scientific Equipments Pvt Ltd, trading as ScienceLab from Ambala, Haryana, India, supplies the Latrine Superstructure Double Cubicle to emergency programmes, schools, institutions and dealers in India and international markets.

What details should a quotation request include?
For a double-cubicle superstructure quotation, give the number of blocks, whether plates and accessibility add-ons are needed, and the delivery destination. Send these through the contact page so the full latrine package can be priced together.

Request a Quote

Ask for pricing on the Latrine Superstructure Double Cubicle via the contact page, or collect it in the enquiry cart with plates and other sanitation items.

Last updated: 24 September 2026

Latrine Add-On Child and Disabled People (Product Code: SLE/SAH/18) is an accessibility kit used to make a standard 120 cm x 80 cm squatting plate easier to use for children and for adults with disabilities in emergency and community sanitation. It consists of an elevated toilet seat with a support frame that can bear a person's weight during independent or assisted transfer, for example from a wheelchair. It is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India, a school laboratory equipment supplier in India that also sources inclusive sanitation items.

Specifications

What Is the Latrine Add-On Kit Used For?

Squatting over a drop hole can be difficult or impossible for people with mobility difficulties, and a standard plate can feel unsafe to small children. This kit places a raised seat over the squatting plate so users can sit instead of squat, while the support frame gives them something firm to hold and lean on as they move between a wheelchair and the seat, alone or with a helper.

Programmes usually fit the add-on to selected latrines in each block rather than every stance. Choose cubicles with enough width for a wheelchair to enter and turn, keep the approach path level and clear, and check that the seat and frame are firmly assembled before the latrine is opened. Asking the intended users for feedback after installation helps confirm that the arrangement works for them.

What to Specify When Ordering

• Number of kits — one for each latrine to be made accessible.
• Confirmation that the latrines use 120 cm x 80 cm squatting plates.
• Superstructure for those latrines, and whether its width suits wheelchair users (ask us for cabin details).
• Main user groups — children, adults with disabilities or both — so we can discuss the kit offered.

Supplier

Jain Scientific Equipments Private Limited supplies this add-on kit under its ScienceLab trading name from Ambala, Haryana. It can be sourced together with plates and cabin kits, helping programmes, schools and dealers in India and international markets plan inclusive latrines in one order. Read about the company on the ScienceLab profile page.

Related Water, Sanitation & Hygiene Supplies

Items used with the accessibility add-on:

• Squatting Plate, Plastic, W/o pan, 120x80cm — a plate in the size the add-on is designed for.
• Latrine Superstructure Single Cubicle — a one-cabin kit for a stand-alone accessible latrine.
• Latrine Superstructure Double Cubicle — a two-cabin block where one cubicle can take the add-on.
• Child Potty — for the youngest children who are not yet using a latrine seat.

See the full Water, Sanitation & Hygiene Supplies range.

Frequently Asked Questions

What does the Latrine Add-On Child and Disabled People kit include?
The Latrine Add-On Child and Disabled People kit is made up of an elevated toilet seat with a support frame. The squatting plate and superstructure are not listed as part of the kit and are ordered separately if needed.

Which squatting plate does the latrine add-on kit fit?
The latrine add-on kit is designed for a standard squatting plate of 120 cm x 80 cm, and one kit is installed on one plate. If your latrines use a different slab, send us its size before ordering so the fit can be discussed.

Can a wheelchair user transfer onto the add-on seat?
Yes, that is its purpose. The support frame of the Latrine Add-On Child and Disabled People kit is designed to carry a person's weight during independent or assisted transfer to and from the seat, such as from a wheelchair. A maximum load figure is not stated, so ask us if you need one.

Where is the latrine add-on kit typically used?
The latrine add-on kit is used with family or communal latrine slabs and in health centres, feeding centres, temporary learning centres, schools and child friendly spaces, particularly during emergencies where accessible latrines must be set up quickly.

Does the latrine need a wider superstructure?
Yes. Latrines chosen for the Latrine Add-On Child and Disabled People kit should have a superstructure wide enough for a wheelchair user to enter and manoeuvre. Ask us for cabin dimensions when planning which cubicles will receive the kit.

Who supplies the Latrine Add-On Child and Disabled People kit?
Jain Scientific Equipments Pvt Ltd, trading as ScienceLab from Ambala, Haryana, India, supplies this latrine add-on kit. Send the quantity, plate size and delivery destination through the contact page for a quotation.

Request a Quote

Request a price for the Latrine Add-On Child and Disabled People kit on the contact page, or add it to the enquiry cart with plates and superstructures for your accessible latrines.

Last updated: 24 September 2026

Sprayer Trigger Bottle Handheld 1 Liter (Product Code: SLE/SAH/19) is a hand-operated plastic trigger sprayer used to apply disinfectant solutions to surfaces in health centres, schools, latrines and other shared spaces. With a 1 litre operating capacity, it is chemically resistant, appropriate for chlorine solutions and fitted with a filter that protects the nozzle. It is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India, a lab consumables supplier in India whose range includes hygiene and cleaning tools.

Specifications

What Is the 1 Litre Trigger Sprayer Used For?

Cleaning teams use this sprayer to wet frequently touched surfaces — latrine slabs and door handles, tables, bed frames, handwashing stations — with a disinfectant solution before wiping or leaving it for the contact time given in their guidance. Because it resists chlorine, it can be filled with the chlorine solutions commonly used in health centres, isolation areas and emergency sanitation, at whatever strength your health guidance specifies.

For safe use, never fill above the maximum line, label each bottle with the solution it holds, and prepare chlorine solution as often as your protocol requires. After each shift, rinse the nozzle and filter with clean water so they do not clog, and store bottles away from direct sunlight and out of the reach of children.

What to Specify When Ordering

• Number of sprayers — for example one per cleaner or per ward, classroom or latrine block.
• Whether larger-area spraying needs compression sprayers as well.
• Any disinfectant, wipes or cloths to be quoted with the sprayers (the sprayer is supplied empty).

Supplier

The handheld trigger sprayer is supplied by Jain Scientific Equipments Private Limited, which does business as ScienceLab from Ambala, Haryana. Health programmes, schools, institutions and dealers in India and international markets can source it together with cleaning cloths, sanitation items and other hygiene supplies. See the ScienceLab company profile for more about us.

Related Water, Sanitation & Hygiene Supplies

Items that complete a surface-disinfection routine:

• Sprayer Compression Type 11.35 Litres — a pump-up sprayer for larger areas and longer spraying runs.
• Multipurpose Cloth Cotton 1x1.5m — a cotton cloth that can be cut for wiping surfaces after spraying.
• Universal Disinfectant Wipes — ready-to-use wipes for small surfaces between spraying rounds.
• Classroom Cleaning & Sanitization Kit — a combined kit for routine school cleaning.

Find more cleaning and hygiene items in Water, Sanitation & Hygiene Supplies.

Frequently Asked Questions

What is the capacity of the Sprayer Trigger Bottle Handheld 1 Liter?
The Sprayer Trigger Bottle Handheld 1 Liter has an operating capacity of 1 litre. The bottle carries a clear, permanent horizontal line marking the maximum liquid volume, and further marks for smaller volume graduations are preferred so users can measure partial fills.

Can the 1 litre trigger sprayer be used with chlorine solutions?
Yes. The 1 litre trigger sprayer is chemically resistant and appropriate for chlorine solutions used in surface disinfection. The sprayer is supplied empty; prepare the chlorine solution at the strength set by your health or infection-prevention guidance.

What does the filter on the trigger sprayer do?
The filter on the Sprayer Trigger Bottle Handheld 1 Liter protects the nozzle from particles that could block the spray. Rinsing the filter and nozzle with clean water after use helps keep the spray pattern even and the trigger working smoothly.

What is the trigger sprayer made of?
The trigger sprayer consists of a plastic bottle with a trigger spray head, built as a sturdy, stable handheld unit. The exact plastic grade is not stated in our listing, so ask us for material details of the model quoted if your protocol requires them.

Who supplies the Sprayer Trigger Bottle Handheld 1 Liter?
Jain Scientific Equipments Pvt Ltd, trading as ScienceLab from Ambala, Haryana, India, supplies the Sprayer Trigger Bottle Handheld 1 Liter to health programmes, schools, institutions and dealers in India and international markets.

How do I request a quotation for trigger sprayers?
To get a quotation for the 1 litre trigger sprayer, send the quantity, delivery destination and any related items such as cloths or compression sprayers through the contact page, so they can be priced in one quote.

Request a Quote

Ask for pricing on the Sprayer Trigger Bottle Handheld 1 Liter through the contact page, or add it to the enquiry cart with your other cleaning and hygiene supplies.

Last updated: 24 September 2026

Sprayer Compression Type 11.35 Litres (Product Code: SLE/SAH/20) is a hand-operated compression sprayer used to apply chlorine solutions, pesticides and insecticides over larger areas in health, sanitation and vector-control work. It holds approximately 11.35 litres, works at an operation pressure of 4 bar and comes with an air pressure gauge, relief valve, lance and trigger valve with lock-off. It is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India, which pairs lab equipment export from India with sourcing of public-health equipment such as this sprayer.

Specifications

What Is the Compression Sprayer Used For?

Health and sanitation teams use this sprayer where a hand bottle is too small: disinfecting floors, walls and latrine blocks with chlorine solution in treatment centres and camps, or applying pesticides and insecticides for pest and vector control. The operator fills the tank through the filtered opening, closes the lid, pumps with the two-handed handle until the gauge shows the working pressure, then sprays with the trigger valve while the flow valve and nozzle control the output.

Good practice is to keep separate, clearly labelled sprayers for chlorine and for pesticides, and to wear the protective equipment named on the chemical's label. Always release the pressure with the safety device before opening the tank, rinse the tank, hose and nozzle with clean water after each job, and hang the lance on its holder so it is not damaged in storage.

What to Specify When Ordering

• Number of sprayers, and whether they are for chlorine, pesticide/insecticide or both (separate units advised).
• Operation pressure if your programme specifies something other than 4 bar.
• Whether spare nozzles or other parts are needed — ask us what can be offered.
• Delivery destination, within India or for export.

Supplier

ScienceLab, the trading name of Jain Scientific Equipments Private Limited in Ambala, Haryana, supplies this compression sprayer to health programmes, municipal and institutional buyers and dealers in India and international markets. For vendor registration and export paperwork, the supplying company is Jain Scientific Equipments Private Limited (IEC AAECJ8618A, GSTIN 06AAECJ8618A1ZT). More background is on the ScienceLab company profile.

Related Water, Sanitation & Hygiene Supplies

Items used with the compression sprayer in cleaning and disinfection work:

• Sprayer Trigger Bottle Handheld 1 Liter — a chlorine-appropriate hand sprayer for small surfaces and spot cleaning.
• Universal Disinfectant Spray — a ready-to-use spray for quick jobs where mixing a solution is not practical.
• Multipurpose Cloth Cotton 1x1.5m — cotton cloth for wiping down sprayed surfaces.
• Garbage Bags, 100 liters — for collecting waste removed during cleaning rounds.

Browse the complete Water, Sanitation & Hygiene Supplies category.

Frequently Asked Questions

What is the capacity of the Sprayer Compression Type 11.35 Litres?
The Sprayer Compression Type 11.35 Litres holds approximately 11.35 litres. Its total weight must not exceed 25 kg when filled to the maximum recommended capacity, which keeps it manageable for an operator carrying it during spraying.

What pressure does the compression sprayer work at?
The compression sprayer has an operation pressure of 4 bar unless otherwise specified. An air pressure gauge shows the tank pressure, and a pressure relief (safety) valve plus a pressure release safety device protect against over-pressure and allow safe opening.

What parts come with the 11.35 litre compression sprayer?
The 11.35 litre compression sprayer includes a cylindrical tank, hand air pump with two-handed handle and locking device, safety and relief valves, air pressure gauge, shut-off valve, hose with dip tube, trigger valve with lock-off, lance, control flow valve, nozzle and a lance hanging system.

Can one compression sprayer be used for both chlorine and pesticides?
The Sprayer Compression Type 11.35 Litres is intended for chlorine, pesticide and insecticide applications. To avoid mixing chemical residues, it is good practice to dedicate and label separate sprayers for chlorine and for pesticides, and to rinse each thoroughly after use.

Is a calibration certificate available for the pressure gauge?
Our listing for the compression sprayer does not mention a calibration certificate for its air pressure gauge. If your programme needs gauge documentation, please raise it through the contact page before ordering so it can be discussed.

Who supplies the Sprayer Compression Type 11.35 Litres?
Jain Scientific Equipments Pvt Ltd, trading as ScienceLab from Ambala, Haryana, India, supplies the Sprayer Compression Type 11.35 Litres to health programmes, institutions and dealers, with vendor registration details available for procurement files.

Request a Quote

Send the quantity, intended chemical use and delivery destination for the Sprayer Compression Type 11.35 Litres through the contact page, or add it to the enquiry cart with related hygiene supplies.

Last updated: 24 September 2026

Torch Handheld Self-Powered (Product Code: SLE/SAH/21) is a small to medium sized LED hand torch used to provide light in camps, shelters, schools and homes without reliable electricity, powered by the user's own winding or pumping. One minute of winding or pumping gives at least 10 minutes of continuous bright white light of at least 50 lumens, with a beam throw of at least 15 m. It is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India, one of India's lab equipment exporters that also source emergency-relief items.

Specifications

What Is the Self-Powered Torch Used For?

Light at night is a basic safety need wherever people live without dependable power. Families and staff use this torch to reach latrines and water points safely after dark, to move around shelters and to carry out household tasks, and schools and health posts keep it for power cuts. Because it is charged by winding or pumping, it does not depend on buying replacement batteries.

For best results, wind or pump for a full minute before setting out, and repeat whenever the light starts to dim. The body is water resistant, so light rain is not a problem, but the torch should not be left submerged. Its impact-resistant ABS body is intended to survive being dropped, which suits children and busy field teams.

What to Specify When Ordering

• Quantity — for example one per household, shelter or latrine block.
• Any preference between a cranking and a pumping mechanism.
• Other household hygiene items to be packed and quoted with the torches.

Supplier

This self-powered torch is supplied by Jain Scientific Equipments Private Limited, which trades as ScienceLab from Ambala, Haryana. Relief programmes, schools, institutions and dealers in India and international markets can source it together with sanitation and hygiene items in a single enquiry. Company details are on the ScienceLab company profile.

Related Water, Sanitation & Hygiene Supplies

Items often supplied alongside a self-powered torch:

• Latrine Superstructure Single Cubicle — a lockable latrine cabin that users reach after dark with the torch.
• Latrine Superstructure Double Cubicle — a two-cabin block for communal sites.
• Multipurpose Cloth Cotton 1x1.5m — a cotton cloth commonly included in household supply kits.
• Soap Toilet Bar Approx. 100-110g Wrapped — a basic hygiene item for the same household distribution.

Explore all Water, Sanitation & Hygiene Supplies.

Frequently Asked Questions

How bright is the Torch Handheld Self-Powered?
The Torch Handheld Self-Powered uses LED bulbs giving white light of at least 50 lumens, with a beam distance (throw) of at least 15 m. That is enough to light a path to a latrine or water point and to work around a shelter at night.

How is the self-powered torch charged?
The self-powered torch is charged by the user, for example with a cranking or pumping mechanism. One minute of winding or pumping gives at least 10 minutes of continuous bright light. Tell us if you prefer one mechanism so we can confirm the model offered.

Is the self-powered torch waterproof?
The Torch Handheld Self-Powered is water resistant, so it can be used in rain and damp conditions. It is not described as submersible, so avoid dropping it into water or leaving it immersed, and dry it before storage.

How robust is the torch body?
The Torch Handheld Self-Powered has an ABS plastic body, or an equivalent material, with impact resistance able to pass a 1.5 m drop test onto a concrete surface, making it suitable for everyday use by families and field staff.

Who supplies the Torch Handheld Self-Powered?
Jain Scientific Equipments Pvt Ltd, trading as ScienceLab from Ambala, Haryana, India, supplies the Torch Handheld Self-Powered to relief programmes, schools, institutions and dealers in India and international markets.

What should I include in a quotation request for torches?
For a quotation on the self-powered torch, share the quantity, any preferred charging mechanism, the delivery destination and any hygiene items to be supplied with it, using the contact page.

Request a Quote

Request pricing for the Torch Handheld Self-Powered through the contact page, or add it to the enquiry cart with your other relief and hygiene items.

Last updated: 24 September 2026

Multipurpose Cloth Cotton 1x1.5m (Product Code: SLE/SAH/22) is a 100% cotton fabric piece used for everyday hygiene and household needs in family kits, shelters, schools and health posts. It measures approximately 1 m x 1.5 m, weighs 170–180 g/m² and is woven with at least 21 warp and 18.5 weft threads per cm, in natural, light brown or grey. It is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India, one of the educational laboratory suppliers in India that also source hygiene textiles.

Specifications

What Is the Multipurpose Cotton Cloth Used For?

As its name says, this cloth has many uses. In household and hygiene kits it serves as a towel, a wrap or cover, a sheet for a child, or a cleaning cloth, and it can be cut into smaller pieces for washing, wiping or personal hygiene. Cotton is absorbent, comfortable against the skin and easy to wash by hand, which is why it is favoured for distributions where people have limited access to other textiles.

The fabric figures tell a buyer how substantial the cloth is: 170–180 g/m² is a medium-weight fabric, and the minimum thread counts in the warp (lengthwise) and weft (crosswise) describe how densely it is woven. The natural, light brown and grey colour options also help hide everyday staining. Washing the cloth before first use is advisable.

What to Specify When Ordering

• Quantity of cloths, for example per household or per kit.
• Preferred colour — natural, light brown or grey.
• Other kit items, such as soap or washing powder, to be quoted in the same order.

Supplier

Jain Scientific Equipments Private Limited, known as ScienceLab, supplies this cotton cloth from Ambala, Haryana, as part of its water, sanitation and hygiene range. Relief programmes, schools, institutions and dealers in India and international markets can combine it with soap, detergent and other household items. The ScienceLab company profile gives more background.

Related Water, Sanitation & Hygiene Supplies

Items that pair with the multipurpose cotton cloth in hygiene kits:

• Laundry Detergent/Washing Powder, 1.5kg — for washing the cloth and other household textiles.
• Soap Toilet Bar Approx. 100-110g Wrapped — a personal hygiene staple for the same kit.
• Reusable Menstrual Set — a dedicated menstrual hygiene item for women and girls.
• Sprayer Trigger Bottle Handheld 1 Liter — for spraying surfaces that the cloth is then used to wipe.

Browse everything in Water, Sanitation & Hygiene Supplies.

Frequently Asked Questions

What size is the Multipurpose Cloth Cotton 1x1.5m?
The Multipurpose Cloth Cotton 1x1.5m measures approximately 1 m x 1.5 m and is made of 100% cotton. The size is large enough to use as a wrap, towel or cover, and the cloth can be cut into smaller pieces for cleaning or personal hygiene.

What fabric weight and thread count does the cotton cloth have?
The multipurpose cotton cloth has a fabric weight of 170–180 g/m², with a minimum of 21 threads per cm in the warp and 18.5 threads per cm in the weft. These figures describe a medium-weight, closely woven cotton fabric.

Which colours is the multipurpose cloth available in?
The Multipurpose Cloth Cotton 1x1.5m is listed in natural, light brown or grey. State your preferred colour, or whether mixed colours are acceptable, when you request a quotation, and we will confirm what can be offered for your quantity.

How should the cotton cloth be cared for?
The multipurpose cotton cloth can be washed by hand with soap or washing powder and dried in the open air. Washing it before first use is advisable, and regular washing and thorough drying keep a cloth used for hygiene purposes clean.

Who supplies the Multipurpose Cloth Cotton 1x1.5m?
Jain Scientific Equipments Pvt Ltd, trading as ScienceLab from Ambala, Haryana, India, supplies the Multipurpose Cloth Cotton 1x1.5m to relief programmes, schools, institutions and dealers in India and international markets.

What do you need to quote for multipurpose cloths?
To quote for the multipurpose cotton cloth, we need the quantity, preferred colour, delivery destination and any other kit items to be supplied with it. Send these through the contact page for a combined quotation.

Request a Quote

Ask for a price on the Multipurpose Cloth Cotton 1x1.5m via the contact page, or add it to the enquiry cart with the rest of your hygiene kit list.

Last updated: 24 September 2026

Child Potty (Product Code: SLE/SAH/23) is a simple, robust plastic potty used for toilet training and for the hygienic collection of young children's faeces in homes, shelters and early-childhood spaces. It measures approximately 20 cm in diameter and is designed to stand stable on the floor while a child uses it. It is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India, a laboratory equipment supplier in India that also sources child hygiene items.

Specifications

What Is the Child Potty Used For?

Small children are often too young to use a latrine safely, and their faeces carry the same germs as those of adults. A potty gives them a safe, familiar place to go, and lets caregivers collect the waste and empty it into a latrine instead of leaving it near the home. That makes the potty a simple but useful part of family hygiene kits, child friendly spaces and early-childhood centres.

After each use, empty the potty into a latrine or toilet, wash it with soap and water, rinse and leave it to dry, and wash both the child's and the caregiver's hands. Placing the potty on a flat floor makes the most of its stable base, and its robust plastic body stands up to daily washing.

Supplier

The Child Potty is supplied by Jain Scientific Equipments Private Limited, which uses the trading name ScienceLab and is based in Ambala, Haryana. Programmes, childcare centres, institutions and dealers in India and international markets can order it together with soap, toothbrushes and other family hygiene items. Visit the ScienceLab profile to learn more about the company.

Related Water, Sanitation & Hygiene Supplies

Items that support safe sanitation for young children:

• Latrine Add-On Child and Disabled People — an elevated seat kit for children who are ready to use a latrine.
• Squatting Plate, Plastic, W/o pan, 120x80cm — a latrine plate with a child-safe keyhole drop hole, where potty contents can be emptied.
• Soap Toilet Bar Approx. 100-110g Wrapped — for washing the potty and hands after every use.
• Toothbrush for Children — another child hygiene item for family kits.

See the complete Water, Sanitation & Hygiene Supplies range.

Frequently Asked Questions

What size is the Child Potty?
The Child Potty has a diameter of approximately 20 cm. It is a simple, robust plastic potty designed to stand stable on the floor, which suits young children who are learning to use a potty and caregivers who need something easy to clean.

Which children is the plastic child potty suitable for?
The plastic child potty is meant for young children who cannot yet use a latrine safely. An age range is not stated in our listing, so caregivers should judge readiness; older children can move on to latrines fitted with a child-friendly seat or keyhole drop hole.

How should the child potty be cleaned?
Empty the child potty into a latrine or toilet after each use, wash it with soap and water, rinse it and let it dry. Caregivers and children should wash their hands with soap afterwards, as child faeces carry the same germs as adult faeces.

What material is the Child Potty made of?
The Child Potty is made of plastic. The specific plastic grade and colour are not stated in our listing, so ask us through the contact page if your programme needs these details for its specifications.

Who supplies the Child Potty?
Jain Scientific Equipments Pvt Ltd, trading as ScienceLab from Ambala, Haryana, India, supplies the Child Potty to humanitarian programmes, childcare centres, institutions and dealers in India and international markets.

Can the Child Potty be ordered in large quantities?
Yes, the Child Potty can be quoted in the quantities needed for family kits or childcare programmes. Send the number required, the delivery destination and any other hygiene items to be supplied with it, and we will prepare a quotation.

Request a Quote

To price the Child Potty, send your quantity and destination through the contact page, or add it to the enquiry cart with other family hygiene supplies.

Last updated: 24 September 2026

Flange GI 2" Bar No Holes (Product Code: SLE/WDF/01) is a round, internally threaded galvanized iron pipe flange used to connect 2" GI water pipes to flanged fittings or flanged pipes in water supply installations. Made of hot-dip galvanized malleable cast iron, threaded after galvanizing and rated for 14 bar (200 lb/sq inch), it is supplied with its bolt holes not drilled. It is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India, a lab equipment exporter that also sources water-distribution fittings.

Specifications

What Is the 2-Inch GI Flange Used For?

Threaded GI pipe and flanged equipment do not join directly. This flange screws onto the threaded end of a 2" GI pipe and turns it into a flanged end that can be bolted, with a gasket, to the matching flange of a valve, pump outlet, meter, tank connection or flanged pipe section. That makes the joint easy to open again for maintenance, which a fully threaded run does not allow.

Because the bolt holes are not drilled, the installer can mark and drill them to match the mating flange exactly, which is useful when equipment from different sources has to be connected. Threading after galvanizing leaves clean threads free of zinc build-up; use a suitable thread sealant when screwing the flange onto the pipe and tighten flange bolts evenly in a cross pattern.

What to Specify When Ordering

• Quantity of 2" flanges required.
• Whether undrilled flanges suit you, or whether you want to ask us about drilling to a stated pattern.
• Other GI fittings, such as nipples, tees and elbows, to be quoted with the flanges.

Supplier

This GI flange is supplied by Jain Scientific Equipments Private Limited, trading as ScienceLab, from Ambala, Haryana. Water supply contractors, programmes and dealers in India and international markets can source it with the rest of our galvanized and plastic pipe fittings. Procurement teams can register the supplying company as Jain Scientific Equipments Private Limited, GSTIN 06AAECJ8618A1ZT, LEI 3358004HRD1JIVXKYX49. More information is on the ScienceLab company profile.

Related Water, Sanitation & Hygiene Supplies

Fittings commonly used in the same GI pipework:

• Tee Reduction fthd GI 2½" x 2" ND 14 Bar — a 14 bar reducing tee with a 2" connection for branching the line.
• Nipple Taper mthd Hex GI 14 Bar — a male-threaded hex nipple for joining female-threaded GI fittings.
• Elbow 90º equal fthd GI ND 14 Bar — for turning the GI line through a right angle.
• Coupler PVC Socket Solvent Cement Joint Flange, 110mm x 4" — another flanged connector in the range, for PVC pipework (check sizes).

Browse all pipe fittings and sanitation items in Water, Sanitation & Hygiene Supplies.

Frequently Asked Questions

What pipe size does the Flange GI 2" Bar No Holes fit?
The Flange GI 2" Bar No Holes fits galvanized iron water pipe of 2" nominal diameter. Its internal female thread screws onto the male-threaded end of the pipe, giving a flanged end that can be bolted to flanged fittings or pipes.

What pressure is the 2-inch GI flange rated for?
The 2-inch GI flange is rated for 14 bar, which is 200 lb/sq inch. The complete joint also depends on the mating flange, gasket and bolts, so check that every part of the connection suits the working pressure of your system.

Why does the GI flange have no bolt holes?
The Flange GI 2" Bar No Holes is supplied with its bolt holes not drilled, so the installer can drill them to match the mating flange exactly. If you need a specific drilling pattern, tell us the details through the contact page before ordering.

What material and finish does the GI flange have?
The GI flange is made of malleable cast iron, hot-dip galvanized for corrosion protection and threaded after galvanizing, so the internal threads are clean and not clogged by the zinc coating when the flange is fitted to a pipe.

Who supplies the Flange GI 2" Bar No Holes?
Jain Scientific Equipments Pvt Ltd, trading as ScienceLab from Ambala, Haryana, India, supplies the Flange GI 2" Bar No Holes to water supply contractors, programmes and dealers, and can share its GSTIN and LEI for vendor registration.

What should a quotation request for GI flanges include?
For a GI flange quotation, give the quantity, confirm the 2" nominal diameter, state whether undrilled flanges are acceptable and list any other GI fittings you need. Adding the delivery destination lets the whole fittings order be quoted together.

Request a Quote

Send your GI flange quantity and fittings list through the contact page, or add this item to the enquiry cart with other pipe fittings.

Last updated: 24 September 2026

Nipple Taper mthd Hex GI 14 Bar (Product Code: SLE/WDF/02) is a ½" galvanized iron hexagon nipple with external tapered male threads, used to join two female-threaded fittings in GI water pipework. It is made of hot-dip galvanized malleable cast iron, threaded after galvanizing, and rated for 14 bar (200 lb/sq inch). It is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India, a laboratory equipment exporter from India that also sources GI pipe fittings for water projects.

Specifications

What Is the GI Hex Nipple Used For?

A nipple is the short connector that links two female-threaded parts placed close together — for example a socket to a tee, a tee to an elbow, or a fitting to a tap or valve body on a ½" GI line. Plumbers use it when building manifolds, tap stands and short branch connections where a length of cut pipe would be impractical.

The hexagon in the middle gives a spanner something to grip, so each end can be tightened without damaging the threads. Because the threads are tapered, the joint becomes tighter as it is screwed in; wrap the threads with a suitable sealing tape or compound first, and avoid over-tightening, which can split the female fitting.

What to Specify When Ordering

• Quantity of ½" hex nipples.
• The thread standard used on your site, so compatibility can be confirmed.
• Matching ½" female-threaded fittings such as tees, sockets and caps.

Supplier

The GI hex nipple is supplied by Jain Scientific Equipments Private Limited, whose trading name is ScienceLab, from Ambala in Haryana. Contractors, water programmes and dealers in India and international markets can order it alongside other galvanized and PVC fittings to complete a pipework list in one enquiry. Read about us on the ScienceLab company profile.

Related Water, Sanitation & Hygiene Supplies

Female-threaded ½" fittings that this nipple connects:

• Tee 90° Equal fthd GI ½" ND 14 Bar — a matching ½" tee for branch connections.
• Socket equal fthd GI ½" ND 14 Bar — a ½" socket for joining the nipple to pipe or other fittings.
• Cap fthd GI 14 Bar — a ½" female cap that closes the end of a nipple.
• Clamp Saddle PP, HDPE 110mm x fthd ½" O/ND-P — a saddle with a ½" female-threaded outlet for tapping off an HDPE main.

See all pipe fittings in Water, Sanitation & Hygiene Supplies.

Frequently Asked Questions

What size is the Nipple Taper mthd Hex GI 14 Bar?
The Nipple Taper mthd Hex GI 14 Bar has a nominal diameter of ½" with external tapered male threads and a hexagon section. It is intended for ½" galvanized iron water pipe fittings that have female threads.

What pressure is the GI hex nipple rated for?
The GI hex nipple is rated for 14 bar, or 200 lb/sq inch. The working pressure of the finished line also depends on the other fittings, the pipe and the quality of each threaded joint, so all parts should suit your system.

Why does the nipple have a hexagon section?
The hexagon section of the Nipple Taper mthd Hex GI 14 Bar gives a spanner a firm grip, so each threaded end can be tightened into its fitting without gripping and damaging the threads themselves.

What material and finish does the hex nipple have?
The hex nipple is made of malleable cast iron that is hot-dip galvanized and then threaded after galvanizing, so the tapered threads are clean and ready for sealing tape or compound when the fitting is installed.

Which thread standard does the hex nipple use?
Our listing for the Nipple Taper mthd Hex GI 14 Bar states a tapered male thread but not the thread standard. Tell us the standard used on your project through the contact page so compatibility can be confirmed before you order.

Who supplies the Nipple Taper mthd Hex GI 14 Bar?
Jain Scientific Equipments Pvt Ltd, trading as ScienceLab from Ambala, Haryana, India, supplies the Nipple Taper mthd Hex GI 14 Bar to contractors, water programmes and dealers in India and international markets.

Request a Quote

Send your quantity and full fittings list through the contact page, or add the hex nipple to the enquiry cart with other GI fittings.

Last updated: 24 September 2026

Plug Hollow mthd GI 14 Bar (Product Code: SLE/WDF/03) is a ½" hollow galvanized iron plug with an external male thread, used to close off unused female-threaded openings in GI water pipe fittings. It is made of malleable cast iron, hot-dip galvanized and threaded after galvanizing, and is rated for 14 bar (200 lb/sq inch). It is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India, which combines scientific equipment bulk supply with sourcing of water-supply fittings.

Specifications

What Is the GI Hollow Plug Used For?

Water systems are rarely built with every outlet in use from day one. This plug screws into a ½" female-threaded opening — the branch of a tee, the end of a socket or elbow, or a spare port — to seal it until a tap, branch line or gauge is added later. It is also handy for closing openings temporarily while a new section of pipework is pressure tested.

When fitting it, clean the female threads, apply sealing tape or compound to the plug's male thread and tighten firmly without forcing. Recording where plugs have been fitted helps maintenance teams find future connection points quickly, and removing a plug is straightforward when the line needs extending.

What to Specify When Ordering

• Number of ½" plugs for spare or future outlets.
• Whether you also need caps for closing male-threaded pipe ends.
• The thread standard on your site, so compatibility can be checked.

Supplier

Jain Scientific Equipments Private Limited, which trades under the ScienceLab name in Ambala, Haryana, supplies this GI plug as part of its water-distribution fittings range. Contractors, programmes and dealers in India and international markets can combine it with tees, sockets, nipples and PVC fittings in one order. Company information is on the ScienceLab profile page.

Related Water, Sanitation & Hygiene Supplies

Fittings that work alongside the hollow plug:

• Cap fthd GI 14 Bar — the female-threaded counterpart for closing male pipe ends.
• Tee 90° Equal fthd GI ½" ND 14 Bar — a ½" tee whose spare branch can be sealed with this plug.
• Socket equal fthd GI ½" ND 14 Bar — a ½" socket that the plug can close at the end of a line.
• Nipple Taper mthd Hex GI 14 Bar — a ½" hex nipple for joining female fittings when the outlet is brought into use.

Browse the full Water, Sanitation & Hygiene Supplies range for more fittings.

Frequently Asked Questions

What does the Plug Hollow mthd GI 14 Bar do?
The Plug Hollow mthd GI 14 Bar seals a ½" female-threaded opening in galvanized iron water pipework, such as the branch of a tee or the end of a socket, until that outlet is needed or while the line is being tested.

What is the difference between a GI plug and a GI cap?
A GI plug, like this hollow male plug, has an external thread and screws into a female-threaded opening. A GI cap has an internal female thread and screws over a male-threaded pipe or nipple end. Choose by the type of thread you need to close.

What pressure is the hollow GI plug rated for?
The hollow GI plug is rated for 14 bar, which equals 200 lb/sq inch. As with any threaded joint, the actual performance also depends on the matching fitting, the thread sealing and correct tightening during installation.

What is the hollow plug made of?
The Plug Hollow mthd GI 14 Bar is made of malleable cast iron, hot-dip galvanized and threaded after galvanizing, which gives a corrosion-resistant zinc finish while keeping the male thread clean for sealing.

Which thread standard does the GI plug use?
The thread standard of the hollow GI plug is not stated in our listing. Please tell us the standard used on your project through the contact page so we can confirm compatibility before you place an order.

Who supplies the Plug Hollow mthd GI 14 Bar?
Jain Scientific Equipments Pvt Ltd, trading as ScienceLab from Ambala, Haryana, India, supplies the Plug Hollow mthd GI 14 Bar to contractors, water programmes and dealers in India and international markets.

Request a Quote

Request pricing for the hollow GI plug through the contact page, or add it to the enquiry cart with the rest of your pipe fittings.

Last updated: 24 September 2026

Cap fthd GI 14 Bar (Product Code: SLE/WDF/04) is a ½" galvanized iron end cap with an internal female parallel thread, used to close the male-threaded end of a GI water pipe or nipple. It is made of malleable cast iron that is hot-dip galvanized and threaded after galvanizing, with a pressure rating of 14 bar (200 lb/sq inch). It is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India, a lab consumables supplier in India whose range extends to water pipe fittings.

Specifications

What Is the GI Pipe Cap Used For?

Every pipe run has to end somewhere. This cap screws over the male-threaded end of a ½" GI pipe or nipple to make a sealed dead end — at the last point of a distribution line, on a stub left for a future tap stand, or on a section being pressure tested before it is connected.

Before fitting, check that the male thread on the pipe or nipple matches the cap's parallel female thread, then seal the male thread with tape or compound and tighten the cap by hand followed by a spanner. When the line is later extended, the cap can simply be unscrewed and replaced with a socket, tee or elbow.

What to Specify When Ordering

• Number of ½" caps for line ends and future extension points.
• The male thread type on your pipes or nipples, so fit can be confirmed.
• Whether plugs are also needed for closing female-threaded openings.

Supplier

ScienceLab is the trading name of Jain Scientific Equipments Private Limited, Ambala, Haryana, which supplies this GI cap within its pipe-fittings range for water projects. Contractors, programmes and dealers in India and international markets can list it with nipples, sockets and tees in a single enquiry. Find out more on the ScienceLab company profile.

Related Water, Sanitation & Hygiene Supplies

Fittings used with the GI cap:

• Nipple Taper mthd Hex GI 14 Bar — a ½" male-threaded nipple whose end this cap can close.
• Plug Hollow mthd GI 14 Bar — the male counterpart for sealing female-threaded openings.
• Socket equal fthd GI ½" ND 14 Bar — the fitting that replaces the cap when a line is extended.
• Tee 90° Equal fthd GI ½" ND 14 Bar — a ½" tee for adding a branch in the same line.

View all fittings in Water, Sanitation & Hygiene Supplies.

Frequently Asked Questions

What does the Cap fthd GI 14 Bar do?
The Cap fthd GI 14 Bar screws over the male-threaded end of a ½" galvanized iron pipe or nipple to seal it, creating a dead end at the last point of a line, on a future connection stub or on a section under pressure test.

What thread does the GI cap have?
The GI cap has an internal female parallel thread in ½" nominal diameter. The thread standard is not stated in our listing, so share the male thread type used on your pipes through the contact page and we will confirm compatibility.

What pressure is the Cap fthd GI 14 Bar rated for?
The Cap fthd GI 14 Bar is rated for 14 bar, or 200 lb/sq inch. Correct thread sealing and tightening are needed for the capped joint to hold pressure, and the rest of the line should be rated for the same working pressure.

What material is the GI pipe cap made of?
The GI pipe cap is made of malleable cast iron, hot-dip galvanized and threaded after galvanizing. The zinc coating protects the iron against corrosion, and threading after galvanizing keeps the internal threads clean and true.

Can the GI cap be removed later to extend the line?
Yes. Because the Cap fthd GI 14 Bar is a threaded fitting, it can be unscrewed when the pipe needs extending and replaced with a socket, tee or elbow; fresh sealing tape or compound should be applied to the thread when reconnecting.

Who supplies the Cap fthd GI 14 Bar?
Jain Scientific Equipments Pvt Ltd, trading as ScienceLab from Ambala, Haryana, India, supplies the Cap fthd GI 14 Bar to contractors, water programmes and dealers in India and international markets.

Request a Quote

Send the number of caps and your other fittings through the contact page, or add the GI cap to the enquiry cart.

Last updated: 24 September 2026

Cross equal fthd GI 4" ND 14 Bar (Product Code: SLE/WDF/05) is a four-way galvanised iron pipe fitting used to join four 4-inch water pipes at a single junction in pressurised water-supply lines. Every outlet has the same 4" nominal diameter and an internal (female) thread, and the body is rated for 14 bar, which suits contractors and water-project teams building distribution headers. It is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India, a laboratory equipment supplier in India that also sources water, sanitation and hygiene items.

Specifications

What Is the 4-Inch GI Equal Cross Used For?

A cross is chosen where one pipe run must meet three others at the same point — for example, a header that takes water from a pump or storage tank and sends it in three directions, or a junction where two supply lines intersect. Because the Cross equal fthd GI 4" ND 14 Bar has female threads on all four sides, each branch is made up with a male-threaded 4" GI pipe end or a threaded nipple. This keeps the junction compact and allows it to be dismantled later if the layout changes.

For a leak-free joint, clean the threads, wrap the male ends with thread-sealing tape or apply a suitable jointing compound, and tighten with pipe wrenches while holding the cross steady. A 4-inch assembly full of water is heavy, so support the pipes on each side of the junction. Pressure-test the completed line within the 14 bar rating before service, and close any outlet that is not needed yet with a threaded plug.

What to Specify When Ordering

• The number of 4" equal crosses needed for each site or project phase.
• Confirmation that your pipes are 4" nominal diameter GI with male threads to suit the female outlets.
• The working and test pressure of your system, so that it stays within the 14 bar rating.
• Companion fittings required in the same order, such as nipples, plugs, bends or elbows.

Supplier

ScienceLab is the trading name of Jain Scientific Equipments Private Limited, a company based in Ambala, Haryana. For this galvanised cross the company acts as supplier: it sources the fitting, prepares the quotation and arranges dispatch together with other water, sanitation and hygiene items that institutions and project buyers order in one lot. For vendor registration, the supplying company is Jain Scientific Equipments Private Limited (CIN U29309HR2020PTC087597, GSTIN 06AAECJ8618A1ZT). Read more about the company on the ScienceLab company profile.

Related Water, Sanitation & Hygiene Supplies

These threaded GI items are commonly ordered with a 4" cross to complete a junction:

• Nipple Taper mthd Hex GI 14 Bar — a male-threaded hex nipple for joining the cross to other female fittings; ask for the matching size.
• Plug Hollow mthd GI 14 Bar — seals an outlet that will be connected later.
• Bend 90º equal fxf GI 4" ND 14 Bar — turns a branch from the cross through a right angle in the same pipe size.
• Elbow 90º equal fthd GI ND 14 Bar — a compact choice where the change of direction must be tight.

See the full range in the Water, Sanitation & Hygiene Supplies category.

Frequently Asked Questions

What size are the outlets on the Cross equal fthd GI 4" ND 14 Bar?
All four outlets of the Cross equal fthd GI 4" ND 14 Bar are 4-inch nominal diameter with internal female threads, so the fitting accepts male-threaded 4" GI pipe or nipples on every side. It is an equal cross, so no outlet is reduced.

What pressure is the 4-inch GI equal cross rated for?
The Cross equal fthd GI 4" ND 14 Bar is rated for 14 bar, which is 200 lb per square inch. Keep the working pressure and the site test pressure of your water line within this figure when planning pumps, tanks and valves around the junction.

What is the cross made of?
The Cross equal fthd GI 4" ND 14 Bar is made of malleable cast iron that is hot-dip galvanised for corrosion protection. Its threads are cut after galvanising, so the zinc coating does not fill the thread form and the fitting screws onto pipe cleanly.

Who supplies the Cross equal fthd GI 4" ND 14 Bar?
Jain Scientific Equipments Pvt Ltd, trading as ScienceLab in Ambala, Haryana, supplies the Cross equal fthd GI 4" ND 14 Bar. The company sources the fitting and quotes it alongside other water, sanitation and hygiene items for buyers in India and international markets.

What should a quotation request for this cross include?
A quotation request for the Cross equal fthd GI 4" ND 14 Bar should state the quantity, the delivery location and any companion fittings you need. If you require supporting documents for the fitting, raise it through the contact page so we can confirm what is available.

Can the 4" GI cross be ordered in bulk or for export?
Yes, bulk and export enquiries for the Cross equal fthd GI 4" ND 14 Bar are welcome. ScienceLab supplies institutions, contractors and project buyers in India and international markets; send quantities and the destination so the quotation can cover packing and freight.

Request a Quote

To price the Cross equal fthd GI 4" ND 14 Bar for your project, send the quantity and delivery location through the ScienceLab contact page, or add it to the enquiry cart with the other fittings on your list. Buyers preparing laboratory equipment tenders in India can include water-supply items like this cross in the same enquiry.

Last updated: 24 September 2026

Bend 90º equal fxf GI 4" ND 14 Bar (Product Code: SLE/WDF/06) is a right-angle galvanised iron pipe bend used to turn a 4-inch threaded water line through 90° in pressurised supply and distribution systems. Both ends are female-threaded (fxf) to the same 4" nominal diameter, so site crews can route mains around corners, walls and tank connections without a change of size. It is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India, together with related water-supply fittings.

Specifications

What Is the 4-Inch GI 90° Bend Used For?

Pipe routes rarely run straight from source to outlet. The Bend 90º equal fxf GI 4" ND 14 Bar lets a 4-inch galvanised main turn a corner — up a wall from a pump, across to an overhead tank or around a building footing — while keeping the same bore on both sides of the turn. Compared with a short elbow, a bend generally sweeps through a gentler curve, which helps water change direction more smoothly in larger lines.

Each end takes a male-threaded 4" GI pipe or a threaded nipple. Seal the male threads with tape or jointing compound, screw each pipe fully home, and set the bend's alignment before the final turn, because a threaded fitting cannot be backed off without loosening the joint. Anchor the pipes close to the turn, where line forces act, and check the finished run against the 14 bar rating during pressure testing.

What to Specify When Ordering

• Quantity of 4" bends for each route or site.
• Confirmation that the line is 4" nominal diameter GI pipe with male-threaded ends.
• Whether a bend or a short elbow suits the space available at each corner.
• Other fittings needed on the same line, such as crosses, nipples or plugs.

Supplier

Jain Scientific Equipments Private Limited, which trades as ScienceLab and is known to many buyers as a laboratory equipment exporter from India, also supplies water-supply fittings such as this 4" bend. The company sources the item and handles quotation, packing and dispatch from Ambala, Haryana, so a buyer can combine pipe fittings with other water, sanitation and hygiene supplies in one order. Company background is available on the ScienceLab profile page.

Related Water, Sanitation & Hygiene Supplies

Fittings that are usually planned on the same galvanised line as this bend:

• Cross equal fthd GI 4" ND 14 Bar — a four-way junction in the same size for branching the main before or after the turn.
• Elbow 90º equal fthd GI ND 14 Bar — the tighter-turn alternative where corner space is limited.
• Nipple Taper mthd Hex GI 14 Bar — a male-threaded connector for joining the bend directly to another female fitting; confirm the size with us.
• Cap fthd GI 14 Bar — a female-threaded cap for closing a male pipe end at the end of a run.

Browse all items in the Water, Sanitation & Hygiene Supplies category.

Frequently Asked Questions

Are both ends of the Bend 90º equal fxf GI 4" ND 14 Bar the same?
Yes. Both ends of the Bend 90º equal fxf GI 4" ND 14 Bar are internal (female) threads of the same 4-inch nominal diameter, which is what "fxf" and "equal" mean in the name. Each end accepts a male-threaded 4" GI pipe or nipple.

How is this bend different from a 90° elbow?
The Bend 90º equal fxf GI 4" ND 14 Bar and a 90° elbow both turn a line through a right angle, but a bend generally follows a longer, gentler curve while an elbow is more compact. Choose the bend where there is room and the elbow where space is tight.

What pressure can the 4" GI bend handle?
The Bend 90º equal fxf GI 4" ND 14 Bar is rated for 14 bar (200 lb per square inch). Size pumps and set test pressures so the line stays within this rating, and make sure every other fitting on the line meets it as well.

What material and finish does the bend have?
The Bend 90º equal fxf GI 4" ND 14 Bar is malleable cast iron, hot-dip galvanised to protect it against corrosion in water service. Threading is done after galvanising, leaving clean threads that engage GI pipe without scraping through built-up zinc.

Who supplies the Bend 90º equal fxf GI 4" ND 14 Bar?
ScienceLab, the trading name of Jain Scientific Equipments Pvt Ltd in Ambala, Haryana, supplies the Bend 90º equal fxf GI 4" ND 14 Bar. It sources the fitting and quotes it with other water-supply items for projects in India and international markets.

How do I get a price for a quantity of these bends?
To price the Bend 90º equal fxf GI 4" ND 14 Bar, send the quantity, delivery location and any other fittings on your list through the contact page. A quotation is then prepared for the complete order, including bulk or export quantities.

Request a Quote

Send your requirement for the Bend 90º equal fxf GI 4" ND 14 Bar through the ScienceLab contact page with quantity and destination, or place it in the enquiry cart while you browse the other GI fittings. One enquiry can cover every fitting on your pipe schedule.

Last updated: 24 September 2026

Elbow 90º equal fthd GI ND 14 Bar (Product Code: SLE/WDF/07) is a compact galvanised iron elbow used to make a tight right-angle turn in 4-inch threaded water pipework in pumping, storage and distribution installations. Its two equal outlets carry internal parallel threads of 4" nominal diameter and the fitting is rated for 14 bar, which suits plumbers working in confined pump rooms and valve chambers. It is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India.

Specifications

What Is the GI 90° Equal Elbow Used For?

An elbow is the fitting of choice where a 4-inch galvanised line has to change direction in a small footprint — at a pump outlet, where a riser leaves the floor, inside a valve pit or where pipes hug a wall. The Elbow 90º equal fthd GI ND 14 Bar turns the flow through a right angle within a short body, so the pipe can sit close to the surface it follows.

Its internal parallel threads receive male-threaded 4" GI pipe or nipples. With a parallel female thread the seal depends on careful thread preparation, so apply thread-sealing tape or jointing compound to the male thread and tighten evenly. Sharp turns add more flow resistance than a long bend, so on long pumped mains use bends where space allows and keep elbows for the tight spots.

What to Specify When Ordering

• The 4" size — the product name does not state it, so write "4 inch nominal diameter" in your enquiry.
• The quantity needed for each site or installation.
• Your system pressure, to confirm it stays within the 14 bar rating.
• Whether any corners would be better served by a longer bend.

Supplier

Buyers who know ScienceLab as a laboratory equipment supplier in India may not expect pipe fittings, but the company — the trading name of Jain Scientific Equipments Private Limited, Ambala — also supplies water, sanitation and hygiene items for institutional and project use. This elbow is sourced by the company and then quoted, packed and dispatched with the rest of an order. For more about the business, see the company profile.

Related Water, Sanitation & Hygiene Supplies

Items that work with this elbow on a 4" GI line or at a plastic-to-GI transition:

• Bend 90º equal fxf GI 4" ND 14 Bar — the gentler-curve alternative in the same size where there is room.
• Cross equal fthd GI 4" ND 14 Bar — a four-way junction for branching a 4" GI main.
• Adaptor PP Comp, HDPE 110mmxmthd GI. 4"O/ND-P — its male GI thread lets an HDPE pipe screw straight into the elbow's female outlet.
• Elbow PP Comp, HDPE 110mmxfthd 4" O/ND-P — a plastic elbow to use when the turn itself is the HDPE-to-GI change-over.

More fittings are listed in the Water, Sanitation & Hygiene Supplies category.

Frequently Asked Questions

What size is the Elbow 90º equal fthd GI ND 14 Bar?
The Elbow 90º equal fthd GI ND 14 Bar is 4-inch nominal diameter on both outlets, according to its specification, even though the size is not written in the product name. Mention "4 inch" when you enquire so the quotation matches your pipework.

What type of thread does the elbow have?
The Elbow 90º equal fthd GI ND 14 Bar has internal female parallel threads on both ends. It accepts male-threaded 4" GI pipe or nipples; seal the male threads with tape or jointing compound so the joint stays watertight under pressure.

What pressure is the 4" GI elbow rated for?
The Elbow 90º equal fthd GI ND 14 Bar carries a pressure rating of 14 bar, equal to 200 lb per square inch. Check your pump's delivery pressure and the line test pressure against this rating before installation.

Should I choose this elbow or a bend?
Choose the Elbow 90º equal fthd GI ND 14 Bar where space is tight, because its body turns the flow in a short distance. Where there is room, a 90° bend of the same size generally gives a smoother turn and less flow resistance on long mains.

Who supplies the Elbow 90º equal fthd GI ND 14 Bar?
Jain Scientific Equipments Pvt Ltd (ScienceLab) of Ambala, Haryana supplies the Elbow 90º equal fthd GI ND 14 Bar. The company sources it and can include it in one quotation with other GI fittings and water-supply items for buyers in India and international markets.

Can the elbow be quoted for an export project?
Yes, the Elbow 90º equal fthd GI ND 14 Bar can be quoted for export as well as domestic delivery. Share the quantity, destination and full fitting list through the contact page, and the quotation will cover the complete requirement.

Request a Quote

Ready to order? List the Elbow 90º equal fthd GI ND 14 Bar with its quantity on the contact form, or save it in the enquiry cart and send your whole list at once. Remember to state the 4" size in your message.

Last updated: 24 September 2026

Tee Reduction fthd GI 2½" x 2" ND 14 Bar (Product Code: SLE/WDF/08) is a galvanised iron reducing tee used to take a smaller 2-inch branch off a 2½-inch threaded water main in pressurised supply networks. The side outlet is reduced to 2" while the run stays at 2½", all three ends are internally threaded, and the fitting is rated for 14 bar. It is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India, for water-supply and institutional projects.

Specifications

What Is the GI Reducing Tee Used For?

Distribution lines often step down in size as they branch: the main carries the full flow while each branch serves a smaller building, tap stand or storage tank. The Tee Reduction fthd GI 2½" x 2" ND 14 Bar does this in one fitting — the main passes straight through at 2½" and the branch leaves at a right angle in 2" — so no separate reducing socket or bush is needed at the junction.

Install it with the straight run in line with the main and the reduced outlet pointing toward the branch. Because the internal threads are parallel, prepare each male pipe end with sealing tape or jointing compound before tightening. Where a branch may need isolating for repairs, plan a valve on the 2" side close to the tee, and pressure-test the finished network within the 14 bar rating.

What to Specify When Ordering

• Confirmation that the main is 2½" and the branch 2" nominal diameter GI pipe.
• The number of tees, usually one for each branch take-off.
• Working and test pressure of the network, so it stays within 14 bar.
• Any straight fittings needed in each size, such as sockets or nipples.

Supplier

ScienceLab, the trading name of Jain Scientific Equipments Private Limited, supplies this reducing tee from Ambala, Haryana as part of its range of water, sanitation and hygiene items. The company sources the fitting and answers each enquiry with a quotation that can bundle every fitting on a project's bill of quantities. Institutions that buy through laboratory equipment tenders in India sometimes include water-supply works as well, and this tee can be priced within the same response. More about the company is on the ScienceLab profile page.

Related Water, Sanitation & Hygiene Supplies

Other threaded GI items used when laying out branch lines:

• Tee 90° Equal fthd GI ½" ND 14 Bar — an equal tee for small-bore service branches further along the network.
• Socket Reduction fthd ¾" x ½" ND 14 Bar — steps smaller service lines down in size.
• Nipple Taper mthd Hex GI 14 Bar — a male-threaded connector for joining the tee to other female fittings; confirm the size you need.
• Plug Hollow mthd GI 14 Bar — closes the branch outlet until the branch line is laid.

The complete range is in the Water, Sanitation & Hygiene Supplies category.

Frequently Asked Questions

Which outlet of the Tee Reduction fthd GI 2½" x 2" ND 14 Bar is reduced?
The side (branch) outlet of the Tee Reduction fthd GI 2½" x 2" ND 14 Bar is the reduced one, at 2-inch nominal diameter, while the straight run is 2½ inch. All three ends are internally threaded to take male GI pipe.

What pressure rating does the reducing tee have?
The Tee Reduction fthd GI 2½" x 2" ND 14 Bar is rated for 14 bar (200 lb per square inch). The rating applies to the fitting itself, so confirm that the pipes, valves and other fittings on the same network are rated for at least the same pressure.

What is the tee made from?
The Tee Reduction fthd GI 2½" x 2" ND 14 Bar is malleable cast iron, hot-dip galvanised to resist corrosion in water service. Its parallel female threads are cut after galvanising, so the thread form stays clean and engages the pipe properly.

Why use a reducing tee instead of an equal tee and a reducer?
The Tee Reduction fthd GI 2½" x 2" ND 14 Bar branches and reduces in one fitting, which gives fewer threaded joints, a shorter assembly and fewer possible leak points than an equal tee combined with a separate reducing socket or bush.

Who supplies the Tee Reduction fthd GI 2½" x 2" ND 14 Bar?
Jain Scientific Equipments Pvt Ltd, which trades as ScienceLab from Ambala, Haryana, supplies the Tee Reduction fthd GI 2½" x 2" ND 14 Bar. It sources the fitting and quotes it for institutional, contractor and project buyers in India and international markets.

What details speed up a quotation?
For a quick quotation on the Tee Reduction fthd GI 2½" x 2" ND 14 Bar, give the quantity, the delivery location and a list of the other fittings on the job. Questions about documentation for the fitting can be raised on the contact page before ordering.

Request a Quote

Add the Tee Reduction fthd GI 2½" x 2" ND 14 Bar to the enquiry cart, or describe your branch layout on the contact page. We will reply with a quotation covering the tees and any related fittings you list.

Last updated: 24 September 2026

Tee 90° Equal fthd GI ½" ND 14 Bar (Product Code: SLE/WDF/09) is a small-bore galvanised iron tee used to split a ½-inch threaded water line into two equal branches for taps, basins and other service points. All three outlets share the same ½" nominal diameter with internal threads, and the fitting is rated for 14 bar, making it a routine item for plumbers fitting out a school laboratory setup in India or a campus washroom. It is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India.

Specifications

What Is the Half-Inch GI Equal Tee Used For?

Half-inch lines are the last stage of most water systems — the pipe that runs along a laboratory bench to its sink taps, feeds a row of wash basins or supplies a hand-wash point. The Tee 90° Equal fthd GI ½" ND 14 Bar lets one such line serve an extra outlet: water continues along the run and also leaves through the side branch at the same size.

Tighten small fittings with care, since over-tightening a half-inch joint strains the thread while too little torque leaves a weep. Wrap the male threads with sealing tape in the direction of the thread, start the pipe by hand, then finish with a wrench. Where several tees sit along a bench line, clip the pipe firmly between them so that repeated tap use does not work the joints loose.

What to Specify When Ordering

• The number of branch points on each line (one tee per take-off).
• Confirmation that the line is ½" nominal diameter GI pipe with male-threaded ends.
• Sockets, nipples or reducing fittings needed to reach each tap connection.

Supplier

Jain Scientific Equipments Private Limited trades as ScienceLab and supplies this half-inch tee, sourcing it for customers who need plumbing items alongside their laboratory or WASH orders. Quotations, packing and dispatch are handled from Ambala, Haryana. For vendor registration and export paperwork, the supplying company's details are IEC AAECJ8618A (DGFT) and GSTIN 06AAECJ8618A1ZT. Background on the business is on the ScienceLab company profile.

Related Water, Sanitation & Hygiene Supplies

Small-bore GI fittings that complete a tap or basin line:

• Socket equal fthd GI ½" ND 14 Bar — joins two lengths of half-inch pipe on the same line.
• Socket Reduction fthd ¾" x ½" ND 14 Bar — steps a three-quarter-inch feed down to the half-inch line the tee sits on.
• Cap fthd GI 14 Bar — closes the far end of a line; confirm the size with us.
• Plug Hollow mthd GI 14 Bar — seals a branch left ready for a future tap.

View every item in the Water, Sanitation & Hygiene Supplies category.

Frequently Asked Questions

What size is the Tee 90° Equal fthd GI ½" ND 14 Bar?
The Tee 90° Equal fthd GI ½" ND 14 Bar is half-inch nominal diameter on all three outlets, each with an internal female thread. As an equal tee, its branch is the same size as the run, so it suits standard half-inch service lines.

What pressure is the half-inch GI tee rated for?
The Tee 90° Equal fthd GI ½" ND 14 Bar is rated for 14 bar, equivalent to 200 lb per square inch. Check this rating against the pressure of your pump, overhead tank or mains supply before installation.

Can this tee be used on a laboratory bench water line?
Yes, the Tee 90° Equal fthd GI ½" ND 14 Bar can branch a half-inch galvanised supply line to feed extra taps or sinks on a laboratory bench, provided the rest of the line is half-inch GI pipe with male-threaded ends.

What are the tee's material and coating?
The Tee 90° Equal fthd GI ½" ND 14 Bar is malleable cast iron with a hot-dip galvanised coating, and its threads are cut after galvanising. The zinc layer protects the body from rust, while threading afterwards keeps the threads clean.

Who supplies the Tee 90° Equal fthd GI ½" ND 14 Bar?
Jain Scientific Equipments Pvt Ltd (ScienceLab), based in Ambala, Haryana, supplies the Tee 90° Equal fthd GI ½" ND 14 Bar. The company sources the fitting and can quote it with other plumbing and WASH items for customers in India and international markets.

Can small quantities be ordered, or only bulk?
Both small and bulk requirements for the Tee 90° Equal fthd GI ½" ND 14 Bar can be sent for quotation. State the exact quantity and delivery location on the contact page, and the reply will confirm what can be supplied.

Request a Quote

Put the Tee 90° Equal fthd GI ½" ND 14 Bar in the enquiry cart with the other half-inch fittings for your installation and submit the list, or write to us through the contact page with quantities and the delivery location.

Last updated: 24 September 2026

Socket Reduction fthd ¾" x ½" ND 14 Bar (Product Code: SLE/WDF/10) is a galvanised malleable iron reducing socket used to join a ¾-inch threaded water pipe to a ½-inch pipe in a straight line. Both ends are internally threaded, one at each nominal size, and the fitting carries a 14 bar pressure rating, so installers use it wherever a feeder narrows to a tap or appliance line. It is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India.

Specifications

What Is the Three-Quarter to Half-Inch Reducing Socket Used For?

Water systems usually carry flow in a larger pipe and narrow it close to the point of use. The Socket Reduction fthd ¾" x ½" ND 14 Bar makes that step in a straight run: the ¾" end takes the feeder pipe and the ½" end takes the smaller line that continues to a tap, valve, float valve or wash point. Because it keeps the pipe axis straight, it is neater than combining an elbow or tee with a separate bush.

Fit the larger pipe first and then the smaller, sealing each male thread with tape or jointing compound. A reducing socket is normally installed so that water flows from the larger size to the smaller one, so check the direction before tightening. As with any threaded joint, support the pipes on both sides so the fitting does not carry bending loads.

What to Specify When Ordering

• Confirmation that your feeder is ¾" and the outgoing line ½" nominal diameter GI pipe.
• The quantity required for each installation.
• Companion fittings in either size that should be quoted with it.

Supplier

This reducing socket is a sourced item supplied by ScienceLab, the trading name of Jain Scientific Equipments Private Limited in Ambala, Haryana. Known to schools and colleges as a laboratory equipment supplier in India, the company also sources plumbing and WASH items so that institutions and project buyers can place one consolidated order. You can read about the company on its profile page.

Related Water, Sanitation & Hygiene Supplies

Fittings often listed with a reducing socket on a service line:

• Socket equal fthd GI ½" ND 14 Bar — a straight coupling for joining two half-inch pipes after the reduction.
• Tee 90° Equal fthd GI ½" ND 14 Bar — branches the half-inch line so it can serve more than one outlet.
• Nipple Taper mthd Hex GI 14 Bar — a short male connector for joining the socket to a female-threaded valve or fitting; confirm the size.
• Cap fthd GI 14 Bar — ends a line neatly where no further outlet is needed.

Find more in the Water, Sanitation & Hygiene Supplies category.

Frequently Asked Questions

What sizes does the Socket Reduction fthd ¾" x ½" ND 14 Bar connect?
The Socket Reduction fthd ¾" x ½" ND 14 Bar connects a three-quarter-inch nominal diameter pipe to a half-inch pipe. Each end has an internal female thread, so both pipes need male-threaded ends.

Is the reducing socket galvanised?
Yes. The Socket Reduction fthd ¾" x ½" ND 14 Bar is malleable cast iron, hot-dip galvanised for protection against rust, with threads cut after galvanising so the zinc does not clog them. It is intended for galvanised water pipe.

What pressure is the reducing socket rated for?
The Socket Reduction fthd ¾" x ½" ND 14 Bar is rated for 14 bar, or 200 lb per square inch. Design the whole line so that its working and test pressures stay within this rating.

When should I use a reducing socket rather than a bush?
Use the Socket Reduction fthd ¾" x ½" ND 14 Bar when both pipes have male threads and you want a straight, in-line change of size. A bush suits a different case: reducing an existing female outlet on another fitting.

Who supplies the Socket Reduction fthd ¾" x ½" ND 14 Bar?
Jain Scientific Equipments Pvt Ltd, trading as ScienceLab in Ambala, Haryana, supplies the Socket Reduction fthd ¾" x ½" ND 14 Bar. It sources the fitting for institutions, contractors and project buyers in India and international markets.

How can I get a quotation for the reducing socket?
To get a quotation for the Socket Reduction fthd ¾" x ½" ND 14 Bar, send the quantity and delivery location through the contact page, or add it to the enquiry cart with the other fittings you need.

Request a Quote

Every quotation for the Socket Reduction fthd ¾" x ½" ND 14 Bar is prepared against your stated quantity and destination. Use the contact page to send those details, or collect the item in the enquiry cart along with the rest of your pipe fittings.

Last updated: 24 September 2026

Socket equal fthd GI ½" ND 14 Bar (Product Code: SLE/WDF/11) is a straight galvanised iron coupling used to join two lengths of ½-inch threaded water pipe end to end in supply and service lines. It has internal parallel threads of the same ½" nominal diameter at both ends and is rated for 14 bar, making it the simplest way to extend or repair a small-bore GI run. It is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India.

Specifications

What Is the Half-Inch GI Equal Socket Used For?

Galvanised pipe comes in fixed lengths, so any run longer than one length needs a joint, and the Socket equal fthd GI ½" ND 14 Bar provides it without changing size or direction. The same fitting is used for repairs: a corroded or cracked section is cut out, the new ends are threaded and a replacement piece is joined in with sockets. During a school laboratory setup in India, half-inch lines to sink taps are often extended this way when benches are added or moved.

Parallel internal threads rely on a good seal at the mating male thread, so apply sealing tape or compound evenly and screw both pipes in until they are firmly engaged from each side. Tighten the second pipe while holding the socket with another wrench, so the first joint is not disturbed. After assembly, flush the line and check the joint for weeping under normal pressure.

Supplier

ScienceLab is the name under which Jain Scientific Equipments Private Limited trades from Ambala, Haryana. Alongside laboratory apparatus, the company supplies sourced plumbing fittings such as this half-inch socket and quotes them on the same enquiry, so an institution can deal with one supplier for bench equipment and the water lines that serve it. The company profile has more background.

Related Water, Sanitation & Hygiene Supplies

Other fittings used on half-inch GI service lines:

• Socket Reduction fthd ¾" x ½" ND 14 Bar — for points where the line must step down in size instead of continuing straight.
• Tee 90° Equal fthd GI ½" ND 14 Bar — adds a same-size branch to the half-inch line.
• Nipple Taper mthd Hex GI 14 Bar — a male nipple that pairs with a socket to join two female fittings; confirm the size.
• Cap fthd GI 14 Bar — seals the open male end of a pipe that will be extended later.

All water, sanitation and hygiene items are grouped in the Water, Sanitation & Hygiene Supplies category.

Frequently Asked Questions

What does "equal" mean in the Socket equal fthd GI ½" ND 14 Bar?
"Equal" means both ends of the Socket equal fthd GI ½" ND 14 Bar are the same size, half-inch nominal diameter, so it joins two pipes of identical bore without any reduction. Both ends are internally threaded.

What kind of thread does the socket have?
The Socket equal fthd GI ½" ND 14 Bar has internal female parallel threads at both ends. It accepts male-threaded half-inch GI pipe; seal the male thread with tape or jointing compound for a watertight connection.

What is the pressure rating of the half-inch GI socket?
The Socket equal fthd GI ½" ND 14 Bar is rated for 14 bar, which is 200 lb per square inch. Keep the working and test pressure of the line within this value when planning the installation.

Can the socket be used to repair a damaged pipe?
Yes, the Socket equal fthd GI ½" ND 14 Bar is commonly used in repairs: remove the damaged length, thread the pipe ends and join in a new piece using sockets. Check the repaired joints for leaks under pressure before closing up.

Who supplies the Socket equal fthd GI ½" ND 14 Bar?
The Socket equal fthd GI ½" ND 14 Bar is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab) of Ambala, Haryana. The company sources it and quotes it with other GI fittings for schools, institutions and project buyers in India and international markets.

What should an enquiry for the socket include?
An enquiry for the Socket equal fthd GI ½" ND 14 Bar should give the quantity, the delivery location and any other fittings you need. Use the contact page or enquiry cart; questions about documentation for the fitting can be raised there too.

Request a Quote

Sockets are usually ordered in quantity with the rest of a pipe schedule. Add the Socket equal fthd GI ½" ND 14 Bar to the enquiry cart, or send your full list through the contact page for a single consolidated quotation.

Last updated: 24 September 2026

Clamp Saddle PP, HDPE 110mm x fthd ½" O/ND-P (Product Code: SLE/WDF/12) is a polypropylene clamp saddle used to take a ½-inch threaded service connection off a 110 mm HDPE water main without cutting the main. It clamps around the pipe, has a single middle outlet with a female thread for GI pipe and is rated for 10 bar at 20°C, which suits crews connecting tap stands and buildings. It is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India.

Specifications

What Is the 110 mm HDPE Clamp Saddle Used For?

When a new house connection, tap stand or school water point has to be fed from an existing HDPE main, a clamp saddle is the least disruptive way to do it. The Clamp Saddle PP, HDPE 110mm x fthd ½" O/ND-P closes around a 110 mm outside-diameter HDPE pipe, and the half-inch galvanised service line is then screwed into its female-threaded outlet.

Typical practice is to fit the saddle on a clean, undamaged section of pipe, tighten the clamp evenly so the seal seats squarely, and then drill the main through the outlet with a suitable cutter. Keep the water temperature within 0 to 50°C, and note that the 10 bar rating is stated at 20°C; plastic fittings generally carry less pressure as temperature rises, so allow a margin in hot climates. The UV-stabilised polypropylene helps where the saddle is exposed to sunlight at a tap stand or open valve box.

What to Specify When Ordering

• Main pipe: 110 mm outside diameter HDPE.
• Branch: ½" GI pipe with a male-threaded end.
• Number of service connections (one saddle per tapping).
• Expected water temperature and pressure, to confirm they fall within 0 to 50°C and 10 bar at 20°C.

Supplier

Jain Scientific Equipments Private Limited, trading as ScienceLab from Ambala, Haryana, supplies this polypropylene clamp saddle as part of a wider range of HDPE, PVC and GI water fittings. Better known as a laboratory equipment supplier in India, the company sources the item and prepares single quotations for projects that need pipe fittings, pumps and hygiene supplies from one vendor. More about the company appears on the ScienceLab profile page.

Related Water, Sanitation & Hygiene Supplies

Items used on the same HDPE main or on the service line leaving the saddle:

• T, PP comp, HDPE 110 x 110 x 110mm OD-P — a full-size branch where a half-inch tapping would be too small.
• Adaptor PP Comp, HDPE 110mmxmthd GI. 4"O/ND-P — joins the same HDPE main to 4" GI sockets at a line end or pump.
• Socket equal fthd GI ½" ND 14 Bar — extends the half-inch GI service pipe leaving the saddle.
• Tee 90° Equal fthd GI ½" ND 14 Bar — splits the service line to feed two taps.

Browse the Water, Sanitation & Hygiene Supplies category for the full range.

Frequently Asked Questions

What pipe sizes does the Clamp Saddle PP, HDPE 110mm x fthd ½" O/ND-P fit?
The Clamp Saddle PP, HDPE 110mm x fthd ½" O/ND-P fits HDPE pipe of 110 mm outside diameter, and its outlet takes a half-inch nominal diameter GI pipe through a female thread. "O/ND" in the name stands for outside/nominal diameter.

What pressure and temperature is the saddle rated for?
The Clamp Saddle PP, HDPE 110mm x fthd ½" O/ND-P is rated for 10 bar at 20°C, with a suitable temperature range of 0 to 50°C. At higher water temperatures a plastic fitting's pressure capacity generally falls, so allow a margin in warm conditions.

What material is the clamp saddle made of?
The Clamp Saddle PP, HDPE 110mm x fthd ½" O/ND-P is reinforced, high-impact-strength polypropylene that is UV stabilised. The UV stabilisation helps the saddle withstand sunlight where it is installed above ground or in an open valve box.

Does the main need to be cut to fit the saddle?
No. The Clamp Saddle PP, HDPE 110mm x fthd ½" O/ND-P clamps around the existing 110 mm HDPE main, and the connection is made by drilling the pipe wall through the saddle outlet, so the main stays in one piece.

Who supplies the Clamp Saddle PP, HDPE 110mm x fthd ½" O/ND-P?
Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, Haryana, supplies the Clamp Saddle PP, HDPE 110mm x fthd ½" O/ND-P. It sources the saddle and quotes it for water-network, institutional and project buyers in India and international markets.

Can the saddle be quoted with other HDPE fittings?
Yes, the Clamp Saddle PP, HDPE 110mm x fthd ½" O/ND-P can be quoted together with the other HDPE, PVC and GI fittings on your list. Send the complete schedule and delivery location through the contact page for one consolidated price.

Request a Quote

Count the service connections you plan and send that number with your enquiry for the Clamp Saddle PP, HDPE 110mm x fthd ½" O/ND-P through the contact page. You can also add the saddle to the enquiry cart together with the GI fittings for each service line.

Last updated: 24 September 2026

Coupler PP Comp, HDPE 110mmxflng 4"O/ND-P (Product Code: SLE/WDF/13) is a polypropylene flanged coupling used to connect a 110 mm HDPE water pipe to 4-inch flanged GI pipework, valves or fittings. One end grips the HDPE pipe with a compression joint and the other is a flange, and the coupler is rated for 10 bar at 20°C, so pump-house and valve-chamber installers can move between plastic and metal lines. It is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India.

Specifications

What Is the HDPE-to-Flange Compression Coupler Used For?

Many water networks run in HDPE underground but meet metal at pump houses, storage tanks, meters and valve chambers, where equipment usually has flanged connections. The Coupler PP Comp, HDPE 110mmxflng 4"O/ND-P bridges that change: the 110 mm HDPE pipe is pushed into the compression end and locked by tightening the nut, while the flanged end bolts to a 4" GI flange or flanged fitting.

Because the joint is mechanical, it can be made without fusion-welding equipment, and the flanged side can later be unbolted for maintenance. Cut the HDPE pipe square, chamfer and clean the end, mark the insertion depth, and tighten the compression nut firmly. On the flange side, use a suitable gasket and tighten the bolts evenly in a cross pattern so the plastic flange is not distorted.

What to Specify When Ordering

• The drilling pattern of the mating 4" GI flange or equipment, so compatibility can be checked.
• Whether bolts, nuts and a gasket are needed with the coupler.
• The quantity, one per HDPE-to-flange connection.
• Operating pressure and temperature, which should stay within 10 bar at 20°C and 0 to 50°C.

Supplier

The coupler is supplied by ScienceLab, the trading name of Jain Scientific Equipments Private Limited of Ambala, Haryana. Better known as a lab equipment exporter, the company also sources HDPE, PVC and GI fittings for water, sanitation and hygiene projects. Institutional and tender buyers who need vendor details for registration can use GSTIN 06AAECJ8618A1ZT and LEI 3358004HRD1JIVXKYX49. Further information is on the company profile.

Related Water, Sanitation & Hygiene Supplies

Other transition and HDPE fittings for the same connection point:

• Adaptor PP Comp, HDPE 110mmxmthd GI. 4"O/ND-P — the threaded alternative when the GI side has a 4" socket instead of a flange.
• Elbow PP Comp, HDPE 110mmxfthd 4" O/ND-P — combines the HDPE-to-GI change-over with a right-angle turn.
• Coupler PVC Socket Solvent Cement Joint Flange, 110mm x 4" — the equivalent flanged coupler for uPVC pipe.
• Coupler Reducing PP Comp, HDPE 110x90mm OD-P — steps the HDPE line down to 90 mm elsewhere on the network.

See all items in the Water, Sanitation & Hygiene Supplies category.

Frequently Asked Questions

What does the Coupler PP Comp, HDPE 110mmxflng 4"O/ND-P connect?
The Coupler PP Comp, HDPE 110mmxflng 4"O/ND-P connects a 110 mm outside-diameter HDPE pipe to 4-inch nominal diameter flanged GI pipe or fittings. The HDPE side uses a compression joint and the other side is a flange.

Is welding needed to install the coupler?
No fusion welding is needed for the Coupler PP Comp, HDPE 110mmxflng 4"O/ND-P. The HDPE pipe is inserted into the compression end and the nut is tightened, while the flanged end is bolted to the mating flange with a gasket.

What pressure and temperature is the coupler rated for?
The Coupler PP Comp, HDPE 110mmxflng 4"O/ND-P is rated for 10 bar at 20°C, with a suitable temperature range of 0 to 50°C. Keep pump delivery and test pressures within this rating, allowing a margin in warm conditions.

Are bolts and a gasket included?
The product details for the Coupler PP Comp, HDPE 110mmxflng 4"O/ND-P do not state that bolts or a gasket are included. Please ask through the contact page, giving your flange details, and we will confirm what the quotation covers.

Who supplies the Coupler PP Comp, HDPE 110mmxflng 4"O/ND-P?
ScienceLab, the trading name of Jain Scientific Equipments Pvt Ltd in Ambala, Haryana, supplies the Coupler PP Comp, HDPE 110mmxflng 4"O/ND-P. It sources the fitting for water-network and institutional projects in India and international markets.

Is the coupler suitable for exposed locations?
The Coupler PP Comp, HDPE 110mmxflng 4"O/ND-P is made of reinforced, high-impact-strength polypropylene that is UV stabilised, which helps it tolerate sunlight in open valve chambers or pump yards. Keep it within the stated 0 to 50°C temperature range.

Request a Quote

For a price on the Coupler PP Comp, HDPE 110mmxflng 4"O/ND-P, send the quantity, your flange details and the delivery location through the contact page, or add it to the enquiry cart with the rest of the HDPE and GI fittings for the job.

Last updated: 24 September 2026

Elbow PP Comp, HDPE 110mmxfthd 4" O/ND-P (Product Code: SLE/WDF/14) is a 90° polypropylene adaptor elbow used to connect a 110 mm HDPE pipe to 4-inch threaded galvanised iron pipe while turning the line through a right angle. The HDPE end is a compression joint and the GI end has a female thread, with a rating of 10 bar at 20°C, which helps where a buried plastic main rises into a metal riser or pump connection. It is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India.

Specifications

What Is the 110 mm HDPE to 4-Inch GI Elbow Used For?

The change from plastic to metal pipe often happens exactly where the line changes direction — a buried HDPE main turning upward into a galvanised riser, or a horizontal HDPE run meeting a GI pipe that drops from a tank. The Elbow PP Comp, HDPE 110mmxfthd 4" O/ND-P handles both jobs in one fitting, so the installer avoids stacking a separate adaptor and a separate elbow at that point.

Make the GI joint first: seal the male thread of the 4" GI pipe with tape or jointing compound and screw it into the female end, taking care not to over-tighten into the polypropylene body. Then cut the HDPE pipe square, deburr it, insert it to full depth in the compression end and tighten the nut. Support the metal riser independently so its weight does not load the plastic elbow.

What to Specify When Ordering

• Pipe on each side: 110 mm OD HDPE and 4" ND GI with a male-threaded end.
• The number of risers or transition points that need an elbow.
• Operating conditions, to confirm they sit within 10 bar at 20°C and 0 to 50°C.

Supplier

Jain Scientific Equipments Private Limited trades as ScienceLab and supplies this elbow from Ambala, Haryana. It is a sourced fitting within the company's water, sanitation and hygiene range, quoted and dispatched together with the GI, PVC and HDPE items a project lists. The ScienceLab profile explains more about the company, which serves institutions in India and international markets.

Related Water, Sanitation & Hygiene Supplies

Fittings that sit on either side of an HDPE-to-GI change-over:

• Adaptor PP Comp, HDPE 110mmxmthd GI. 4"O/ND-P — a straight transition with a male GI thread when no turn is needed.
• Coupler PP Comp, HDPE 110mmxflng 4"O/ND-P — the flanged version for connecting to valves or pumps.
• Bend 90º equal fxf GI 4" ND 14 Bar — continues the GI side with a further turn in the same 4" size.
• Nipple Taper mthd Hex GI 14 Bar — a short male piece to join the elbow's female end directly to another female fitting; confirm the size.

Explore the Water, Sanitation & Hygiene Supplies category for more.

Frequently Asked Questions

What are the two ends of the Elbow PP Comp, HDPE 110mmxfthd 4" O/ND-P?
The Elbow PP Comp, HDPE 110mmxfthd 4" O/ND-P has a compression end for 110 mm outside-diameter HDPE pipe and a female-threaded end for 4-inch nominal diameter GI pipe. The two ends sit at 90° to each other.

What pressure and temperature can the elbow handle?
The Elbow PP Comp, HDPE 110mmxfthd 4" O/ND-P is rated for 10 bar at 20°C and suits a temperature range of 0 to 50°C. Where water or ambient temperatures run high, keep system pressure comfortably below the rated figure.

Why use this elbow instead of a straight adaptor and a GI elbow?
The Elbow PP Comp, HDPE 110mmxfthd 4" O/ND-P changes material and direction in a single fitting, which means one joint fewer, a shorter assembly and less weight hanging on the HDPE pipe than a straight adaptor combined with a separate GI elbow.

What is the elbow made from?
The Elbow PP Comp, HDPE 110mmxfthd 4" O/ND-P is made from reinforced, high-impact-strength polypropylene with UV stabilisation, giving a tough body that resists sunlight where the riser connection is above ground.

Who supplies the Elbow PP Comp, HDPE 110mmxfthd 4" O/ND-P?
Jain Scientific Equipments Pvt Ltd, trading as ScienceLab in Ambala, Haryana, supplies the Elbow PP Comp, HDPE 110mmxfthd 4" O/ND-P. The company sources it and quotes it for water-supply, institutional and project buyers in India and international markets.

How do I request a price for the elbow?
To price the Elbow PP Comp, HDPE 110mmxfthd 4" O/ND-P, send the quantity and delivery location through the contact page, or add it to the enquiry cart. Mention any matching GI or HDPE fittings so they can be quoted together.

Request a Quote

Add the Elbow PP Comp, HDPE 110mmxfthd 4" O/ND-P to the enquiry cart or write to us through the contact page. If the elbow is part of a larger institutional package, such as laboratory equipment tenders in India that include water works, list it on the same enquiry.

Last updated: 24 September 2026

T, PP comp, HDPE 110 x 110 x 110mm OD-P (Product Code: SLE/WDF/15) is an equal polypropylene compression tee used to split or join 110 mm HDPE water pipes at a full-size branch in distribution networks. All three ends are compression joints for pipe of 110 mm outside diameter, and the tee is rated for 10 bar at 20°C, so network crews can add a branch without fusion-welding equipment. It is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India.

Specifications

What Is the 110 mm HDPE Compression Tee Used For?

An equal tee is chosen when a branch needs the same capacity as the main — splitting a transmission line into two supply zones, feeding a second storage tank, or closing a loop so that water can reach an area from two directions. The T, PP comp, HDPE 110 x 110 x 110mm OD-P does this on 110 mm HDPE pipe using mechanical compression joints on every end.

Each joint is made by cutting the pipe square, chamfering and cleaning it, pushing it fully into the fitting and tightening the nut. Since no heat or power is needed, the tee suits field repairs and remote sites, and it can be reopened if the layout changes. Bed the tee on firm, even ground in the trench and backfill carefully around it so the branch pipe does not put bending strain on the fitting.

Supplier

ScienceLab is the trading name of Jain Scientific Equipments Private Limited, a laboratory equipment exporter from India based in Ambala, Haryana, whose supply range also covers water, sanitation and hygiene items. The company sources this HDPE compression tee and quotes it with matching couplers, adaptors and saddles, so a network project can be supplied as one package. Learn more on the ScienceLab profile page.

Related Water, Sanitation & Hygiene Supplies

HDPE fittings that are typically ordered with an equal tee:

• Coupler Reducing PP Comp, HDPE 110x90mm OD-P — reduces a branch from the tee to 90 mm pipe.
• Clamp Saddle PP, HDPE 110mm x fthd ½" O/ND-P — for small service tappings where a full-size tee is not required.
• Elbow PP Comp, HDPE 110mmxfthd 4" O/ND-P — turns a branch up into a 4" GI riser.
• Adaptor PP Comp, HDPE 110mmxmthd GI. 4"O/ND-P — connects a branch straight into 4" GI sockets.

The whole range is in the Water, Sanitation & Hygiene Supplies category.

Frequently Asked Questions

What size pipe does the T, PP comp, HDPE 110 x 110 x 110mm OD-P take?
The T, PP comp, HDPE 110 x 110 x 110mm OD-P takes HDPE pipe of 110 mm outside diameter on all three ends. It is an equal tee, so the branch carries the same pipe size as the run.

What is the pressure rating of the 110 mm HDPE tee?
The T, PP comp, HDPE 110 x 110 x 110mm OD-P is rated for 10 bar at 20°C, with a suitable temperature range of 0 to 50°C. In hot conditions allow a margin below the rated pressure, as plastic fittings generally lose capacity as temperature rises.

Does the tee need electrofusion or butt welding?
No. The T, PP comp, HDPE 110 x 110 x 110mm OD-P uses compression joints on each end, so the HDPE pipes are connected mechanically by inserting and tightening, without fusion-welding machines or power on site.

Can the tee be used for a smaller branch?
The T, PP comp, HDPE 110 x 110 x 110mm OD-P is equal on all ends. For a smaller branch, fit a reducing coupler on the branch outlet, or use a clamp saddle on the main where only a small service tapping is needed.

Who supplies the T, PP comp, HDPE 110 x 110 x 110mm OD-P?
Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, Haryana, supplies the T, PP comp, HDPE 110 x 110 x 110mm OD-P. The company sources the tee for water networks, institutions and project buyers in India and international markets.

What information does a quotation for the tee need?
A quotation for the T, PP comp, HDPE 110 x 110 x 110mm OD-P needs the quantity, the delivery location and any other HDPE fittings you plan to use. Send these through the contact page so all items can be priced together.

Request a Quote

Use the contact page to send quantities of the T, PP comp, HDPE 110 x 110 x 110mm OD-P and the rest of your HDPE fitting list, or add the tee to the enquiry cart. Network buyers often combine tees, couplers and saddles in a single request.

Last updated: 24 September 2026

Adaptor PP Comp, HDPE 110mmxmthd GI. 4"O/ND-P (Product Code: SLE/WDF/16) is a straight polypropylene adaptor used to connect a 110 mm HDPE water pipe into a 4-inch female-threaded GI socket, valve or fitting. One end is a compression joint for the HDPE pipe and the other carries an external (male) thread, with a rating of 10 bar at 20°C, which makes it a simple in-line link between plastic mains and threaded metal hardware. It is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India.

Specifications

What Is the HDPE to Male GI Thread Adaptor Used For?

HDPE pipe cannot be threaded, so wherever a plastic main has to enter threaded metal hardware an adaptor is needed. The Adaptor PP Comp, HDPE 110mmxmthd GI. 4"O/ND-P screws its male thread into a 4" female GI socket — for example a socket on a steel riser, the female end of a GI cross, bend or elbow, or a threaded valve body — and accepts the 110 mm HDPE pipe in its compression end.

Wrap the male thread with sealing tape and screw it into the metal socket firmly but without excessive force, since a plastic thread can be damaged by over-tightening. Then prepare the HDPE end with a square cut, chamfer and clean, and tighten it into the compression side. Where the adaptor enters heavy metal pipework, support the metal side so that the plastic body does not take bending loads.

What to Specify When Ordering

• The 4" female GI fitting or valve the adaptor will screw into.
• The number of HDPE-to-GI transitions on the layout.
• Operating pressure and temperature, to confirm they stay within 10 bar at 20°C and 0 to 50°C.

Supplier

Jain Scientific Equipments Private Limited, trading as ScienceLab from Ambala, Haryana, supplies this compression adaptor as part of its water, sanitation and hygiene range. The company, whose core business includes lab equipment export from India, sources plumbing items like this for institutions and project buyers and handles the quotation, packing and dispatch. See the company profile for details.

Related Water, Sanitation & Hygiene Supplies

Fittings on the metal and plastic sides of this adaptor:

• Cross equal fthd GI 4" ND 14 Bar — a 4" female-threaded junction the adaptor can screw into.
• Elbow 90º equal fthd GI ND 14 Bar — another 4" female fitting that can receive the adaptor at a turn.
• Coupler PP Comp, HDPE 110mmxflng 4"O/ND-P — the choice for flanged rather than threaded connections.
• T, PP comp, HDPE 110 x 110 x 110mm OD-P — branches the HDPE main before the transition.

More items are in the Water, Sanitation & Hygiene Supplies category.

Frequently Asked Questions

Which ends does the Adaptor PP Comp, HDPE 110mmxmthd GI. 4"O/ND-P have?
The Adaptor PP Comp, HDPE 110mmxmthd GI. 4"O/ND-P has a compression end for 110 mm outside-diameter HDPE pipe and an external (male) thread for 4-inch nominal diameter GI pipe sockets. It is a straight fitting with no change of direction.

What does the male thread connect to?
The male thread of the Adaptor PP Comp, HDPE 110mmxmthd GI. 4"O/ND-P screws into a 4-inch female-threaded GI socket, fitting or threaded valve. Where the GI pipe presents a male end instead, a female-threaded transition fitting is needed.

What pressure and temperature is the adaptor rated for?
The Adaptor PP Comp, HDPE 110mmxmthd GI. 4"O/ND-P is rated for 10 bar at 20°C and a temperature range of 0 to 50°C. Keep pump and test pressures within this rating and allow extra margin in warm conditions.

What is the adaptor made of?
The Adaptor PP Comp, HDPE 110mmxmthd GI. 4"O/ND-P is reinforced, high-impact-strength polypropylene with UV stabilisation, so the body is tough and tolerates sunlight at above-ground connections such as pump outlets and tank risers.

Who supplies the Adaptor PP Comp, HDPE 110mmxmthd GI. 4"O/ND-P?
The Adaptor PP Comp, HDPE 110mmxmthd GI. 4"O/ND-P is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, Haryana. The company sources it and quotes it for water-supply projects and institutions in India and international markets.

Can I order the adaptor together with GI fittings?
Yes, the Adaptor PP Comp, HDPE 110mmxmthd GI. 4"O/ND-P can be quoted together with the 4" GI fittings it connects to. List every item with its quantity on the contact page or in the enquiry cart for one combined quotation.

Request a Quote

Tell us how many HDPE-to-GI transitions your layout has and what each adaptor screws into, then send those details for the Adaptor PP Comp, HDPE 110mmxmthd GI. 4"O/ND-P through the contact page. You can also add it to the enquiry cart while you select the other fittings.

Last updated: 24 September 2026

Coupler Reducing PP Comp, HDPE 110x90mm OD-P (Product Code: SLE/WDF/17) is a straight polypropylene reducing coupler used to join a 110 mm HDPE pipe to a 90 mm HDPE pipe in water supply mains. Both ends are female compression joints, one for each outside diameter, and the coupler is rated for 10 bar at 20°C, letting network installers step the pipe size down without welding. It is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India.

Specifications

What Is the 110 x 90 mm HDPE Reducing Coupler Used For?

Water networks are commonly laid in stepped sizes: the pipe nearest the source carries the whole flow, and diameters reduce further out as fewer connections remain. The Coupler Reducing PP Comp, HDPE 110x90mm OD-P marks that step between 110 mm and 90 mm HDPE pipe. It is equally useful on repair and extension jobs, where a new 110 mm line has to meet an existing 90 mm pipe.

Install the reducer in line with both pipes, each cut square, chamfered and pushed fully home before its compression nut is tightened. Water moves faster through the smaller pipe for the same flow, so place the joint in a straight, well-supported section of trench and bed it evenly. Record the location on the as-built drawing so maintenance teams know where the size changes.

What to Specify When Ordering

• Both pipe sizes: 110 mm and 90 mm outside diameter HDPE.
• The number of size changes on the network, one coupler for each.
• Pressure and temperature conditions, which should stay within 10 bar at 20°C and 0 to 50°C.

Supplier

Jain Scientific Equipments Private Limited, trading as ScienceLab in Ambala, Haryana, supplies this reducing coupler as a sourced item within its water, sanitation and hygiene range. For institutions procuring through laboratory equipment tenders in India or other vendor-registered channels, the supplying company's details are CIN U29309HR2020PTC087597 and GSTIN 06AAECJ8618A1ZT. The company profile gives more background.

Related Water, Sanitation & Hygiene Supplies

Fittings used alongside a reducer on HDPE and PVC networks:

• T, PP comp, HDPE 110 x 110 x 110mm OD-P — a full-size branch on the 110 mm main before the reduction.
• Clamp Saddle PP, HDPE 110mm x fthd ½" O/ND-P — for service tappings along the 110 mm section.
• Coupler PP Comp, HDPE 110mmxflng 4"O/ND-P — connects the 110 mm line to flanged valves or pumps.
• Reducing Coupler PVC skt scj 110x90mm-P — the solvent-cement equivalent for uPVC pipe networks.

The full selection is in the Water, Sanitation & Hygiene Supplies category.

Frequently Asked Questions

Which pipe sizes does the Coupler Reducing PP Comp, HDPE 110x90mm OD-P join?
The Coupler Reducing PP Comp, HDPE 110x90mm OD-P joins HDPE pipe of 110 mm outside diameter to HDPE pipe of 90 mm outside diameter. Both ends are female compression joints, so nothing needs to be threaded or welded.

What is the pressure rating of the reducing coupler?
The Coupler Reducing PP Comp, HDPE 110x90mm OD-P is rated for 10 bar at 20°C, with a suitable temperature range of 0 to 50°C. Design working and test pressures to stay within this rating, particularly where the water temperature is high.

Can the coupler join HDPE to PVC pipe?
The Coupler Reducing PP Comp, HDPE 110x90mm OD-P is specified for HDPE pipes. For uPVC networks, see the solvent-cement reducing coupler in the same sizes in our WASH range, and ask us about transitions between the two materials.

Can the reducing coupler be dismantled later?
Compression joints like those on the Coupler Reducing PP Comp, HDPE 110x90mm OD-P can generally be opened by loosening the nuts, which helps during repairs or layout changes. Inspect the pipe ends and sealing surfaces carefully before reassembly.

Who supplies the Coupler Reducing PP Comp, HDPE 110x90mm OD-P?
Jain Scientific Equipments Pvt Ltd (ScienceLab) of Ambala, Haryana, supplies the Coupler Reducing PP Comp, HDPE 110x90mm OD-P. The company sources it for water-network, institutional and project buyers in India and international markets, quoting it with related HDPE fittings.

What should I send to get a quotation?
Send the quantity of the Coupler Reducing PP Comp, HDPE 110x90mm OD-P, the delivery location and any other HDPE or GI fittings you need through the contact page. A consolidated quotation is then prepared for the complete list.

Request a Quote

Enquire about the Coupler Reducing PP Comp, HDPE 110x90mm OD-P on the contact page, or place it in the enquiry cart with the tees, saddles and adaptors on your pipe schedule. Include the number of size changes in your network so quantities match the layout.

Last updated: 24 September 2026

Dewatering Pump, 11-22 cbm/hr@50m TMH (Product Code: SLE/WDF/18) is an air-powered diaphragm dewatering unit used to keep hand-dug wells free of water while they are being dug and deepened. It delivers up to 22 m³/hr, or 11 m³/hr against a 50 m total manometric head, and it is self-priming, can run dry and handles water with relatively high solid content, which suits well-digging teams and WASH contractors. It is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India.

Specifications

What Is the Dewatering Pump Used For?

Digging a well by hand means working below the water table, where water keeps seeping into the shaft. The Dewatering Pump, 11-22 cbm/hr@50m TMH removes that inflow so the crew can keep excavating and lining the well. Its diaphragm design copes with muddy, sandy water that can quickly wear other pump types, and because it can run dry, it is not harmed when the shaft is pumped empty between inflows.

The pump is driven by compressed air rather than an electric motor. A diesel engine on the two-wheeled trolley drives the air compressor at the surface, so no mains power connection is needed at the well. Fill the fuel tank before a shift, since it holds enough for 12 hours of continuous normal operation, check the oil-bath air filter often in dusty conditions, and keep the compressor's pressure safety valve in working order.

What to Specify When Ordering

• The expected depth and head at your well sites, compared with the listed 11 m³/hr at 50 m TMH.
• The number of units required for the programme.
• Any accessories or spares you would like quoted — ask us what can be included.
• The delivery location and site access for a trolley-mounted unit.

Supplier

This pump is a sourced unit supplied by ScienceLab, the trading name of Jain Scientific Equipments Private Limited, Ambala, Haryana. Recognised by schools and colleges as a laboratory equipment supplier in India, the company also supplies pumps and fittings for water, sanitation and hygiene work and can quote the dewatering unit with the other items a well-construction programme needs. See the ScienceLab profile for more about the company.

Related Water, Sanitation & Hygiene Supplies

Pumps and hand pumps used before and after a well is completed:

• Pump Centrifugal, Diesel 50cbm/hr — a diesel-driven centrifugal pump listed for larger transfer duties.
• Pump Electric sbmr bh 18cbm/hr — an electric pump option for permanent supply once a water source is in service.
• Handpump Variant 3 Norm — a hand pump for fitting on a completed well.
• Handpump DA 9-15m Variant — a direct-action hand pump variant for shallower wells.

Browse the Water, Sanitation & Hygiene Supplies category for the full range.

Frequently Asked Questions

What flow does the Dewatering Pump, 11-22 cbm/hr@50m TMH deliver?
The Dewatering Pump, 11-22 cbm/hr@50m TMH has a listed maximum capacity of 22 m³ per hour and delivers 11 m³ per hour against a total manometric head of 50 m. Actual output on site depends on the head and conditions at each well.

What powers the dewatering pump?
The Dewatering Pump, 11-22 cbm/hr@50m TMH is an air-powered diaphragm pump. Its air comes from a compressor mounted on a two-wheeled trolley, working at 7 bar with a pressure safety valve and directly flange-coupled to an air-cooled, direct-injection diesel engine.

Can the pump handle muddy water or run dry?
Yes. The Dewatering Pump, 11-22 cbm/hr@50m TMH is self-priming, can run dry and can handle water with relatively high solid content, which suits the silty inflow that is common during hand-dug well excavation.

How long can the engine run on one tank of fuel?
The engine of the Dewatering Pump, 11-22 cbm/hr@50m TMH has a fuel tank sized for 12 hours of continuous normal operation. It also has an oil-bath air filter, a soundproof muffler, a speed governor and rope or recoil starting.

Who supplies the Dewatering Pump, 11-22 cbm/hr@50m TMH?
Jain Scientific Equipments Pvt Ltd, trading as ScienceLab in Ambala, Haryana, supplies the Dewatering Pump, 11-22 cbm/hr@50m TMH. The company sources the unit and quotes it for well-construction, WASH and institutional projects in India and international markets.

What should a quotation request for the pump include?
A quotation request for the Dewatering Pump, 11-22 cbm/hr@50m TMH should state the number of units, the delivery location and the expected well depth. Questions about spares, documentation or accessories can be raised on the contact page so we can confirm what is available.

Request a Quote

Send your requirement for the Dewatering Pump, 11-22 cbm/hr@50m TMH through the contact page, including the number of well sites and the delivery destination, or add the unit to the enquiry cart together with any hand pumps or fittings for the completed wells.

Last updated: 24 September 2026

Coupler PVC Socket Solvent Cement Joint Flange, 110mm x 4" (Product Code: SLE/WDF/19) is a uPVC flanged coupler with collar used to connect 110 mm PVC water pipe to 4-inch flanged pipes, valves or fittings. The pipe end is joined by solvent cement in a socket, the other end is a flange, and the coupler is rated for 10 bar at 20°C, which suits PVC network installers who need a removable connection at pumps and valve chambers. It is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India.

Specifications

What Is the 110 mm uPVC Flanged Coupler Used For?

uPVC pipe is joined permanently with solvent cement, which is ideal along a buried line but inconvenient wherever equipment may have to be removed. The Coupler PVC Socket Solvent Cement Joint Flange, 110mm x 4" gives the line a flanged end at those points — a pump delivery, a flow meter, a sluice valve or a steel pipe section — so the equipment can later be unbolted without cutting the PVC.

For the solvent joint, cut the 110 mm pipe square, remove burrs, clean both surfaces, apply a cement suitable for uPVC to pipe and socket, and push home with a slight twist. Hold the joint briefly and let it cure for the time the cement's instructions give before pressure testing. On the flange side, align the bolt holes, fit a suitable gasket and tighten the bolts evenly in a cross pattern so the uPVC flange seats without stress.

What to Specify When Ordering

• The drilling pattern of the mating 4" flange, so compatibility can be checked.
• Whether solvent cement, a gasket or bolts should be quoted with the coupler — ask us what can be included.
• The quantity, one for each flanged connection on the PVC line.

Supplier

ScienceLab, the trading name of Jain Scientific Equipments Private Limited in Ambala, Haryana, supplies this uPVC flanged coupler from its water, sanitation and hygiene range. Many buyers first know the company as a laboratory equipment exporter from India; for pipeline projects it sources fittings such as this one and combines them in a single quotation with pumps, HDPE fittings and GI items. Details are on the ScienceLab company profile.

Related Water, Sanitation & Hygiene Supplies

Other fittings for 110 mm PVC and HDPE lines:

• Coupler PP Comp, HDPE 110mmxflng 4"O/ND-P — the flanged coupler equivalent for HDPE pipe.
• Union Equal PVC, fxf, scj 10Bar 110mm OD-P — a dismantling joint within a solvent-cement PVC line.
• Reducing Coupler PVC skt scj 110x90mm-P — steps the uPVC line down to 90 mm.
• Tee Adaptor fxf, scj, PVC 110mm x 4" fthd O/ND-P — a PVC tee with a 4" threaded branch.

See the complete Water, Sanitation & Hygiene Supplies category.

Frequently Asked Questions

What does the Coupler PVC Socket Solvent Cement Joint Flange, 110mm x 4" connect?
The Coupler PVC Socket Solvent Cement Joint Flange, 110mm x 4" connects 110 mm outside-diameter PVC pipe to 4-inch nominal diameter flanged pipes or fittings. The PVC pipe is solvent-cemented into its socket, while the flanged end bolts to the mating flange.

What material is the flanged coupler made of?
The Coupler PVC Socket Solvent Cement Joint Flange, 110mm x 4" is made of uPVC, unplasticised polyvinyl chloride, the rigid form of PVC used for pressure water pipe. It is intended for solvent-cement jointing with PVC pipes.

What pressure and temperature rating does the coupler have?
The Coupler PVC Socket Solvent Cement Joint Flange, 110mm x 4" is rated for 10 bar at 20°C, with a suitable temperature range of 0 to 50°C. Allow extra margin where water temperatures are high, as PVC generally loses pressure capacity with heat.

Can the coupler be removed once installed?
The solvent-cement side of the Coupler PVC Socket Solvent Cement Joint Flange, 110mm x 4" is a permanent joint, but the flanged side can be unbolted, so the connected valve, pump or pipe section can be removed without cutting the PVC line.

Who supplies the Coupler PVC Socket Solvent Cement Joint Flange, 110mm x 4"?
Jain Scientific Equipments Pvt Ltd, trading as ScienceLab in Ambala, Haryana, supplies the Coupler PVC Socket Solvent Cement Joint Flange, 110mm x 4". It sources the fitting for water-network, institutional and project buyers in India and international markets.

What should an enquiry for the coupler include?
An enquiry for the Coupler PVC Socket Solvent Cement Joint Flange, 110mm x 4" should include the quantity, delivery location, flange details and any other PVC fittings needed. Send it through the contact page so everything can be quoted together.

Request a Quote

Quote requests for the Coupler PVC Socket Solvent Cement Joint Flange, 110mm x 4" can be sent through the contact page; mention your flange details and the quantity. Alternatively, add it to the enquiry cart along with the unions, reducers and tees on your PVC pipe schedule.

Last updated: 24 September 2026

Cap, female PVC, scj, 110mm OD-P (Product Code: SLE/WDF/20) is a uPVC end cap used to seal the open end of a 110 mm outside-diameter PVC pipe in pressurised water-supply lines. Contractors, WASH programmes and campus maintenance teams fit it wherever a run must stop, for example during a school lab renovation or a new water main; its female socket is solvent-cemented over the pipe and it is rated 10 bar at 20°C. It is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India.

Specifications

What Is the 110mm PVC End Cap Used For?

An end cap is the full stop of a pipeline. On a 110 mm uPVC main it closes the far end of a distribution line, blanks off a stub left for a later connection, or seals a finished section so it can be filled and checked before the rest of the network is joined. Because the socket is solvent-welded, the closure is permanent: to extend the line later, the pipe is cut behind the cap and a new fitting is cemented on.

For a sound joint, cut the pipe square, remove burrs, clean both surfaces, apply solvent cement to the pipe end and the socket, push the cap fully home and hold it briefly. Let the joint cure as the cement maker directs before pressurising, and keep the working pressure within the 10 bar at 20°C rating, remembering that PVC carries less pressure as water temperature rises towards the 50°C limit.

What to Specify When Ordering

• Pipe size: this cap suits pipe of 110 mm outside diameter only.
• Joint system: confirm your pipe is solvent-cement uPVC, not a rubber-ring or HDPE compression line.
• Quantity: one cap for every dead end or reserved stub on the drawing.
• Companion fittings: list any 110 mm couplers, tees or unions needed in the same order.

Supplier

Jain Scientific Equipments Private Limited trades as ScienceLab and supplies this 110 mm uPVC end cap from Ambala, Haryana. Alongside its laboratory ranges, the company sources water-supply fittings so that schools, NGOs, contractors and importers can place one consolidated order with a single laboratory equipment supplier in India. Company background is on the ScienceLab profile page.

Related Water, Sanitation & Hygiene Supplies

These fittings from the same 110 mm uPVC series are often ordered with the end cap:

• Coupler Straight/Equal PVC, skt, scj, 110mm-P — joins two pipe lengths on the run leading to the capped end.
• Union Equal PVC, fxf, scj 10Bar 110mm OD-P — fitted upstream of the cap when the line may need to be opened later.
• Reducing Tee, PVC, fxf, scj, 10Bar, 110x90mm OD-P — takes a 90 mm branch off the same main before it ends.
• Tee Adaptor fxf, scj, PVC 110mm x 4" fthd O/ND-P — branches the 110 mm line to threaded G.I. pipework.

See the full range of pipe fittings, pumps and hygiene items in Water, Sanitation & Hygiene Supplies.

Frequently Asked Questions

What pipe size does the Cap, female PVC, scj, 110mm OD-P fit?
The Cap, female PVC, scj, 110mm OD-P fits PVC pipe with a 110 mm outside diameter. Its female socket slides over the pipe end and is fixed with solvent cement, so the pipe OD must match exactly; for other sizes, ask us through the contact page.

What pressure and temperature is the 110mm PVC end cap rated for?
The 110mm PVC end cap (Cap, female PVC, scj, 110mm OD-P) is rated 10 bar at 20°C and suits water between 0 and 50°C. Allowable pressure is lower at warmer temperatures, so the system designer should confirm the working pressure for the actual water temperature.

Can the 110mm PVC end cap be removed and reused?
No. The 110mm PVC end cap is solvent-welded, so the joint is permanent. To extend the line, cut the pipe behind the cap and cement on a new fitting such as a straight coupler; if reopening is expected, fit a union upstream instead.

Can the Cap, female PVC, scj, 110mm OD-P be used on drinking-water lines?
Drinking-water suitability of the Cap, female PVC, scj, 110mm OD-P should be confirmed with us for your application before you order. Describe the line and what it will carry through the contact page, and ask what information is available for the batch you are quoted.

Who supplies the Cap, female PVC, scj, 110mm OD-P?
Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, Haryana, supplies the Cap, female PVC, scj, 110mm OD-P, sourcing it for schools, WASH projects, contractors and dealers in India and international markets together with its laboratory and hygiene ranges.

What should a quotation request for the 110mm PVC cap include?
A quotation request for the 110mm PVC cap should give the product code SLE/WDF/20, the quantity, the delivery location and any other 110 mm fittings needed, so ScienceLab can price the whole pipe order in one reply.

Request a Quote

Send your quantity and delivery details through the ScienceLab contact page, or add this cap to the enquiry cart with the other fittings you need and request one combined quotation.

Last updated: 24 September 2026

Elbow 90º, PVC scj/fthd, 40mm x 1¼"-P (Product Code: SLE/WDF/21) is a 90° transition elbow used to connect a 40 mm outside-diameter PVC pipe to a 1¼" nominal-diameter galvanised iron (G.I.) pipe in water-supply installations. Plumbers and project teams use it where a plastic line turns a corner and changes to metal in one fitting: one end is a solvent-cement socket, the other a female thread. It is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India.

Specifications

What Is the 40mm PVC to GI Elbow Used For?

Mixed PVC and G.I. pipework is common where a buried plastic line rises to a metal riser, a stand post or a threaded valve. This elbow handles both jobs at once: it turns the flow through 90° and converts the 40 mm solvent-weld PVC pipe to a 1¼" threaded G.I. connection, saving a separate bend and adaptor and one extra joint.

Many installers make the threaded connection first and cement the PVC side afterwards, so turning the elbow on the thread does not disturb a fresh solvent joint. Seal the male G.I. thread with PTFE tape rather than a paste that may not suit PVC, and tighten by hand plus a modest turn, because over-tightening can split a plastic female thread. Keep service within 10 bar at 20°C and the 0 to 50°C range.

What to Specify When Ordering

• PVC side: 40 mm outside diameter, solvent-cement pipe.
• G.I. side: 1¼" nominal diameter pipe with a male thread to enter the female end.
• Quantity: count each point where the line both turns and changes material.
• Other sizes: if your PVC or G.I. sizes differ, ask us before ordering.

Supplier

ScienceLab is the trading name of Jain Scientific Equipments Private Limited, which supplies this PVC-to-G.I. elbow from Ambala, Haryana, together with a wider set of water-supply and sanitation items for institutions and project buyers. For vendor registration, the supplying company's Importer-Exporter Code is AAECJ8618A (DGFT) and its GSTIN is 06AAECJ8618A1ZT. Read more on the company profile.

Related Water, Sanitation & Hygiene Supplies

Fittings that sit on either side of a PVC-to-G.I. change of direction:

• Elbow 90º equal fthd GI ND 14 Bar — an all-G.I. bend for runs that stay in metal.
• Elbow Equal PVC fxf, Solvent Cement Joint, 32mm OD-P — an all-PVC elbow for smaller solvent-weld branches.
• Adaptor fxm, scj, PVC 110mm x GI.4" O/ND-P — a straight PVC-to-G.I. transition for 110 mm mains.
• Cap fthd GI 14 Bar — closes a male-threaded G.I. end during staged work.

Browse all pipe fittings and hygiene products in Water, Sanitation & Hygiene Supplies.

Frequently Asked Questions

Which pipes does the Elbow 90º, PVC scj/fthd, 40mm x 1¼"-P connect?
The Elbow 90º, PVC scj/fthd, 40mm x 1¼"-P connects a PVC pipe of 40 mm outside diameter, cemented into its socket, to a G.I. pipe of 1¼" nominal diameter, screwed into its female thread, while turning the line through 90°.

What is the pressure rating of the 40mm x 1¼" PVC elbow?
The 40mm x 1¼" PVC elbow (Elbow 90º, PVC scj/fthd, 40mm x 1¼"-P) is rated 10 bar at 20°C and suits water from 0 to 50°C. Warmer water reduces the pressure a PVC fitting can safely carry, so design for the actual service temperature.

How should the threaded end of the 40mm PVC to GI elbow be sealed?
Seal the male G.I. thread entering the 40mm PVC to GI elbow with PTFE tape and avoid heavy wrenching, since over-tightening can crack a plastic female thread. Choose any thread compound only if its maker states it is compatible with PVC.

Is the Elbow 90º, PVC scj/fthd, 40mm x 1¼"-P suitable for drinking water?
Please check with us before using the Elbow 90º, PVC scj/fthd, 40mm x 1¼"-P on a drinking-water line. Tell us the application and the water source through the contact page, and ScienceLab will reply with what it can confirm for the supplied batch.

Who supplies the 40mm x 1¼" PVC to GI elbow?
Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, Haryana, supplies the 40mm x 1¼" PVC to GI elbow to schools, WASH programmes, contractors and dealers across India and international markets, alongside its laboratory equipment and hygiene ranges.

Request a Quote

Tell us the quantity of product code SLE/WDF/21 and your delivery location through the contact page, or place it in the enquiry cart with the rest of your PVC and G.I. fittings for a single quotation.

Last updated: 24 September 2026

Elbow Equal PVC fxf, Solvent Cement Joint, 32mm OD-P (Product Code: SLE/WDF/22) is a small-bore uPVC equal elbow used to change the direction of a 32 mm outside-diameter PVC water line in building and site plumbing. Both ends are female sockets joined by solvent cement, which suits service lines to taps, hand-wash points and sinks, including a new school lab setup. It is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India.

Specifications

What Is the 32mm PVC Equal Elbow Used For?

Smaller 32 mm lines carry water from a main or tank to the points where people actually use it: wash basins, taps, laboratory sinks and toilet blocks. They run along walls, under benches and around columns, and every corner needs an elbow. Because both sockets are the same size, this fitting simply turns the pipe without changing its bore.

Dry-fit the run first and mark the alignment on pipe and fitting, since a solvent joint allows no adjustment once it grabs. Then cut square, deburr, clean, cement and push home in one movement to the mark. Support the pipe with clips on either side of the elbow so the joint is not carrying the weight of the line.

What to Specify When Ordering

• Pipe size: 32 mm outside diameter on both ends.
• Joint type: solvent-cement uPVC pipe (not threaded or compression).
• Quantity: count every bend on the layout drawing, plus a few spares for site changes.
• Transitions: note any point where the 32 mm line meets G.I. pipe, which needs a threaded fitting instead.

Supplier

This 32 mm elbow is supplied by Jain Scientific Equipments Private Limited, the company behind the ScienceLab name in Ambala, Haryana. Schools, colleges and WASH project teams that buy laboratory items from ScienceLab can add plumbing fittings like this one to the same enquiry rather than sourcing them separately. More about the company is on the profile page.

Related Water, Sanitation & Hygiene Supplies

Other fittings used when routing water lines of different sizes and materials:

• Elbow 90º, PVC scj/fthd, 40mm x 1¼"-P — a bend that also changes a 40 mm PVC line to threaded G.I.
• Elbow 90º equal fthd GI ND 14 Bar — the threaded G.I. equivalent for metal sections.
• Reducing Tee, PVC, fxf, scj, 10Bar, 110x90mm OD-P — branches a larger supply main upstream of the service lines.
• Elbow 90º Equal PVC, fxf, rrj, 200mm OD-P — a rubber-ring elbow for large-diameter mains.

The complete list of fittings, pumps and hygiene products is in Water, Sanitation & Hygiene Supplies.

Frequently Asked Questions

What pipe does the Elbow Equal PVC fxf, Solvent Cement Joint, 32mm OD-P fit?
The Elbow Equal PVC fxf, Solvent Cement Joint, 32mm OD-P fits uPVC pipe of 32 mm outside diameter on both ends. Each end is a female socket that receives the pipe and is fixed with solvent cement, so both pipes must be the same 32 mm size.

What does fxf mean on the 32mm PVC equal elbow?
On the 32mm PVC equal elbow, fxf means female x female: both ends are sockets that the pipe slides into. There is no male spigot or thread, so the elbow joins two plain pipe ends directly by solvent cement.

What pressure can the 32mm PVC equal elbow handle?
The 32mm PVC equal elbow (Elbow Equal PVC fxf, Solvent Cement Joint, 32mm OD-P) is rated 10 bar at 20°C, with a suitable temperature range of 0 to 50°C. The safe working pressure is lower in warmer water, so check it against your system design.

Is the Elbow Equal PVC fxf, Solvent Cement Joint, 32mm OD-P suitable for drinking water?
Drinking-water suitability of the Elbow Equal PVC fxf, Solvent Cement Joint, 32mm OD-P is something to confirm with us for your specific installation. If a tender or project file needs this point settled, raise it through the contact page before ordering.

Who supplies the 32mm PVC equal elbow?
Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, Haryana, supplies the 32mm PVC equal elbow to schools, institutions, contractors and dealers in India and international markets, and can quote it together with other water-supply fittings.

Request a Quote

For pricing on product code SLE/WDF/22, send the quantity and delivery location through the contact page, or add it to the enquiry cart along with the other fittings on your plumbing list.

Last updated: 24 September 2026

Union Equal PVC, fxf, scj 10Bar 110mm OD-P (Product Code: SLE/WDF/23) is a uPVC pipe union used to join two 110 mm outside-diameter PVC pipes with a connection that can later be opened for maintenance in water-supply systems. Utility, WASH and campus maintenance teams place it beside pumps, meters and valves; both female ends are solvent-cemented and the fitting is rated 10 bar at 20°C. It is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India.

Specifications

What Is the 110mm PVC Union Used For?

Most solvent-weld joints are permanent, which makes equipment hard to remove. A union solves this: it is designed so the pipeline can be separated at the fitting without cutting pipe. Placing a 110 mm union on each side of a pump, flow meter, filter or valve lets that item be lifted out for repair and refitted, while the rest of the network stays intact.

Dry-assemble the union before cementing so you know how its parts go together, because the order cannot be changed once the ends are bonded. Cement each 110 mm pipe fully into its socket, let the joints cure, and only then pressurise. Leave enough clearance around the union for hands and tools, and keep operation within the 10 bar at 20°C rating.

What to Specify When Ordering

• Pipe size: 110 mm outside diameter uPVC on both sides.
• Number of service points: usually two unions for each pump, meter or valve to be removable.
• Pressure class: confirm 10 bar at 20°C suits your system.
• Other fittings: list couplers, tees or caps for the same 110 mm line.

Supplier

Jain Scientific Equipments Private Limited, known to customers as ScienceLab, supplies this 110 mm PVC union from its base in Ambala, Haryana. Water-supply fittings are sourced for schools, NGOs, contractors and dealers who want one point of contact for both laboratory and infrastructure purchases. See the ScienceLab company profile for background.

Related Water, Sanitation & Hygiene Supplies

Items commonly planned together with a removable joint on a 110 mm line:

• Pump Centrifugal, Diesel 50cbm/hr — equipment whose pipe connections are often fitted with unions for servicing.
• Coupler Straight/Equal PVC, skt, scj, 110mm-P — a permanent straight joint where no opening is needed.
• Reducing Tee, PVC, fxf, scj, 10Bar, 110x90mm OD-P — branches the 110 mm main to a 90 mm line.
• Cap, female PVC, scj, 110mm OD-P — closes the end of the same 110 mm run.

More fittings, pumps and hygiene supplies are listed under Water, Sanitation & Hygiene Supplies.

Frequently Asked Questions

What is the Union Equal PVC, fxf, scj 10Bar 110mm OD-P used for?
The Union Equal PVC, fxf, scj 10Bar 110mm OD-P joins two 110 mm PVC pipes with a connection that can be separated later, so pumps, meters or valves on the line can be removed for maintenance without cutting the pipe.

How is the 110mm PVC union different from a straight coupler?
The 110mm PVC union can be opened after installation, whereas a straight coupler forms a permanent solvent-welded joint. Use the union where access is needed later and a coupler where the pipe will never be disconnected.

What pressure rating does the 110mm PVC union have?
The 110mm PVC union (Union Equal PVC, fxf, scj 10Bar 110mm OD-P) is rated 10 bar at 20°C and suits water from 0 to 50°C. At higher water temperatures the safe pressure falls, so confirm working conditions with your system designer.

Can the Union Equal PVC, fxf, scj 10Bar 110mm OD-P be used on drinking-water lines?
Confirm with ScienceLab before fitting the Union Equal PVC, fxf, scj 10Bar 110mm OD-P to a drinking-water line. Share the project details through the contact page and ask what information can be provided for the batch in your quotation.

Who supplies the 110mm PVC union?
Jain Scientific Equipments Pvt Ltd (ScienceLab) of Ambala, Haryana, supplies the 110mm PVC union for schools, WASH programmes, contractors and importers in India and international markets, and can combine it with other 110 mm fittings in one quotation.

Request a Quote

To price product code SLE/WDF/23, share the quantity and delivery location via the contact page, or add the union to the enquiry cart together with the other items for your pump or valve station.

Last updated: 24 September 2026

Tee Adaptor fxf, scj, PVC 110mm x 4" fthd O/ND-P (Product Code: SLE/WDF/24) is a uPVC tee used to take a threaded 4" galvanised iron (G.I.) branch off a 110 mm outside-diameter PVC main in water-supply networks. Its two run ends are female solvent-cement sockets for the PVC pipe, while the third outlet is female threaded for the G.I. pipe, giving a mixed-material junction in one piece. It is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India.

Specifications

What Is the 110mm x 4 inch PVC Tee Adaptor Used For?

Water schemes often combine a PVC trunk main with G.I. branches, risers or older threaded pipework. This tee lets the 110 mm PVC main run straight through while a 4" G.I. pipe or threaded fitting is screwed into the side outlet, so the branch can feed a riser, an existing metal network or a threaded valve assembly without a separate adaptor.

Screw the G.I. branch in first, sealed with PTFE tape and tightened with care, then solvent-cement the two PVC run ends. Support the metal branch independently with clamps or a pipe support, because a heavy G.I. pipe hanging off a plastic thread strains the fitting. Operate within 10 bar at 20°C and 0 to 50°C.

What to Specify When Ordering

• Main size: 110 mm outside diameter PVC, solvent-cement jointed.
• Branch size: 4" nominal diameter G.I. pipe with a male thread.
• Number of branch points on the network drawing.
• If the branch should stay in PVC, consider an all-PVC tee instead and tell us which.

Supplier

ScienceLab, the trading name of Jain Scientific Equipments Private Limited in Ambala, Haryana, supplies this PVC tee adaptor as part of a sourced range of pipe fittings, pumps and hygiene products for institutional and project buyers. Customers ordering laboratory equipment can include these items in the same enquiry. Learn more on the company profile page.

Related Water, Sanitation & Hygiene Supplies

Other ways to join 110 mm PVC to 4" G.I. pipework, and alternative tees:

• Adaptor fxm, scj, PVC 110mm x GI.4" O/ND-P — an in-line transition with a male thread.
• Adaptor fxf, scj, PVC 110mm x GI.4" O/ND-P — an in-line transition with female ends.
• Reducing Tee, PVC, fxf, scj, 10Bar, 110x90mm OD-P — an all-PVC tee when the branch stays in plastic.
• T, PP comp, HDPE 110 x 110 x 110mm OD-P — a compression tee for 110 mm HDPE pipe.

All pipe fittings and related products are in Water, Sanitation & Hygiene Supplies.

Frequently Asked Questions

What connections does the Tee Adaptor fxf, scj, PVC 110mm x 4" fthd O/ND-P have?
The Tee Adaptor fxf, scj, PVC 110mm x 4" fthd O/ND-P has two female solvent-cement sockets for 110 mm outside-diameter PVC pipe and one female threaded outlet for 4" nominal-diameter G.I. pipe.

What do O/ND and fthd mean in the 110mm x 4" tee adaptor name?
In the 110mm x 4" tee adaptor name, O/ND means the PVC size is an outside diameter (110 mm) and the G.I. size is a nominal diameter (4"), while fthd means female threaded, describing the branch outlet.

What pressure is the 110mm x 4" PVC tee adaptor rated for?
The 110mm x 4" PVC tee adaptor is rated 10 bar at 20°C, with a suitable temperature range of 0 to 50°C. PVC carries less pressure in warmer water, so the designer should confirm the working pressure for the expected temperature.

Is the Tee Adaptor fxf, scj, PVC 110mm x 4" fthd O/ND-P suitable for drinking water?
Drinking-water use of the Tee Adaptor fxf, scj, PVC 110mm x 4" fthd O/ND-P should be discussed with us for your application first. Send the scheme details through the contact page so ScienceLab can tell you what it is able to confirm for the supplied batch.

Who supplies the 110mm x 4" PVC tee adaptor?
Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, Haryana, supplies the 110mm x 4" PVC tee adaptor to schools, WASH projects, contractors and dealers across India and international markets, and can quote it with matching PVC and G.I. fittings.

Request a Quote

Request pricing for product code SLE/WDF/24 by sending quantity and delivery location through the contact page, or add it to the enquiry cart with the rest of your network fittings.

Last updated: 24 September 2026

Reducing Tee, PVC, fxf, scj, 10Bar, 110x90mm OD-P (Product Code: SLE/WDF/25) is a uPVC reducing tee used to split a PVC water line into a branch of a different size, for pipes of 110 mm and 90 mm outside diameter. Network planners use it where a sub-main leaves the main supply at a smaller bore; every end is a female socket joined by solvent cement, rated 10 bar at 20°C. It is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India.

Specifications

What Is the 110 x 90mm PVC Reducing Tee Used For?

In a distribution network the flow shrinks as water is drawn off, so branch lines are often a size smaller than the main. A reducing tee makes that step at the junction itself, which avoids adding a separate equal tee and reducer and cuts the number of joints. Typical uses are feeding a school block, a hostel or a group of stand posts from a 110 mm supply.

A reducing tee normally carries the larger size on the straight run and the smaller size on the branch; check the fitting on receipt and plan the layout accordingly. Solvent-cement each socket after cleaning and deburring, and anchor the branch near the tee so pipe movement does not load the junction. Keep pressures within 10 bar at 20°C.

What to Specify When Ordering

• Sizes: 110 mm and 90 mm outside-diameter uPVC pipe.
• Configuration: tell us which size your run and branch need so we can confirm the fitting matches.
• Quantity: one tee per branch take-off on the network plan.
• Matching items: 110 mm and 90 mm couplers, reducers or unions for the same job.

Supplier

This reducing tee is supplied by Jain Scientific Equipments Private Limited, trading as ScienceLab, from Ambala, Haryana. The company sources pipe fittings for water-supply and sanitation work so that institutions and contractors can combine them with laboratory purchases. For vendor registration, the supplying company's details are GSTIN 06AAECJ8618A1ZT and LEI 3358004HRD1JIVXKYX49. See the ScienceLab profile for more.

Related Water, Sanitation & Hygiene Supplies

Fittings used alongside a 110 x 90 mm branch junction:

• Reducing Coupler PVC skt scj 110x90mm-P — steps the same sizes down in a straight line with no branch.
• Coupler Reducing PP Comp, HDPE 110x90mm OD-P — the equivalent reduction for HDPE pipe with compression joints.
• Union Equal PVC, fxf, scj 10Bar 110mm OD-P — adds a removable joint on the 110 mm main.
• Tee Adaptor fxf, scj, PVC 110mm x 4" fthd O/ND-P — a tee whose branch connects to threaded G.I. pipe.

Browse the full Water, Sanitation & Hygiene Supplies range for more fittings.

Frequently Asked Questions

What pipe sizes does the Reducing Tee, PVC, fxf, scj, 10Bar, 110x90mm OD-P join?
The Reducing Tee, PVC, fxf, scj, 10Bar, 110x90mm OD-P joins uPVC pipes of 110 mm and 90 mm outside diameter. All ends are female sockets fixed with solvent cement; tell us your run and branch sizes so we can confirm the configuration.

Why use the 110 x 90mm PVC reducing tee instead of an equal tee?
The 110 x 90mm PVC reducing tee branches and reduces in one fitting, so a separate reducer is not needed. Fewer joints mean less cementing work and fewer possible leak points on the network.

What is the pressure rating of the 110 x 90mm PVC reducing tee?
The 110 x 90mm PVC reducing tee is rated 10 bar at 20°C and is suitable for water from 0 to 50°C. Because PVC loses pressure capacity as temperature rises, confirm the design pressure for the actual water temperature.

Is the Reducing Tee, PVC, fxf, scj, 10Bar, 110x90mm OD-P for drinking water?
Ask us to confirm drinking-water suitability of the Reducing Tee, PVC, fxf, scj, 10Bar, 110x90mm OD-P for your network before ordering. Where a tender or project needs this point answered in writing, raise it through the contact page when you request the quotation.

Who supplies the 110 x 90mm PVC reducing tee?
Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, Haryana, supplies the 110 x 90mm PVC reducing tee to schools, WASH programmes, contractors and importers in India and international markets, together with other PVC fittings.

Request a Quote

Send the quantity of product code SLE/WDF/25 and your delivery location via the contact page, or add the tee to the enquiry cart with the other items on your network bill of materials.

Last updated: 24 September 2026

Adaptor fxm, scj, PVC 110mm x GI.4" O/ND-P (Product Code: SLE/WDF/26) is a straight uPVC adaptor used to connect a 110 mm outside-diameter PVC pipe to 4" nominal-diameter galvanised iron (G.I.) pipework in water-supply lines. One end is a female solvent-cement socket for the PVC pipe; the other is a male BS thread that screws into a female-threaded G.I. fitting or valve. It is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India.

Specifications

What Is the 110mm PVC to 4 inch GI Male Adaptor Used For?

When a new PVC main has to connect into existing metal pipework, the join usually happens at a threaded G.I. socket, a threaded valve or another female-threaded fitting. This adaptor is cemented onto the end of the 110 mm PVC pipe and its male thread is then screwed into that metal fitting, giving a straight, in-line change from plastic to G.I.

Wrap the male plastic thread with PTFE tape and tighten steadily; a plastic male thread in a metal socket needs firm but not excessive torque. It helps to screw the adaptor into the G.I. fitting first and cement the PVC pipe afterwards, so the solvent joint is not twisted. Use the fitting within 10 bar at 20°C and 0 to 50°C.

What to Specify When Ordering

• PVC side: 110 mm outside diameter, solvent-cement pipe.
• G.I. side: a 4" female-threaded fitting to receive the male BS thread; tell us your thread standard so we can confirm it matches.
• Male or female: if your G.I. side ends in a male pipe thread, you need the female-ended adaptor instead.
• Quantity of transition points on the drawing.

Supplier

Jain Scientific Equipments Private Limited supplies this male-threaded PVC adaptor under its ScienceLab name from Ambala, Haryana. Water and sanitation items like this are sourced for schools, public-health projects, contractors and dealers, and can be quoted on the same enquiry as laboratory equipment. Background on the company is on the profile page.

Related Water, Sanitation & Hygiene Supplies

Alternatives and companions for joining 110 mm plastic pipe to 4" metal pipework:

• Adaptor fxf, scj, PVC 110mm x GI.4" O/ND-P — the female-both-ends version for a male-threaded G.I. pipe end.
• Adaptor PP Comp, HDPE 110mmxmthd GI. 4"O/ND-P — a male-threaded adaptor for HDPE rather than PVC pipe.
• Tee Adaptor fxf, scj, PVC 110mm x 4" fthd O/ND-P — used when the G.I. connection is a side branch.
• Coupler Straight/Equal PVC, skt, scj, 110mm-P — extends the PVC pipe up to the transition point.

Find more fittings in Water, Sanitation & Hygiene Supplies.

Frequently Asked Questions

What does the Adaptor fxm, scj, PVC 110mm x GI.4" O/ND-P connect?
The Adaptor fxm, scj, PVC 110mm x GI.4" O/ND-P connects a 110 mm outside-diameter PVC pipe, cemented into its female socket, to 4" nominal-diameter G.I. pipework through its male BS thread.

What is the difference between the fxm and fxf 110mm x 4" PVC adaptors?
The fxm 110mm x 4" PVC adaptor has a male thread that screws into a female G.I. fitting, while the fxf version has female ends on both sides. Choose by whether the G.I. connection you meet is female or male.

What pressure rating does the 110mm x 4" fxm PVC adaptor have?
The 110mm x 4" fxm PVC adaptor is rated 10 bar at 20°C and suits water from 0 to 50°C. As water temperature rises the allowable PVC pressure drops, so the design pressure should allow for service conditions.

Is the Adaptor fxm, scj, PVC 110mm x GI.4" O/ND-P suitable for drinking water?
Suitability of the Adaptor fxm, scj, PVC 110mm x GI.4" O/ND-P for drinking water should be confirmed with us against your application. Describe the pipeline through the contact page and ask what information is available for the batch before placing the order.

Who supplies the 110mm x 4" fxm PVC adaptor?
Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, Haryana, supplies the 110mm x 4" fxm PVC adaptor for water projects, schools, contractors and dealers in India and international markets, and can quote matching PVC and G.I. fittings.

Request a Quote

Ask for a price on product code SLE/WDF/26 through the contact page with your quantity and delivery location, or add it to the enquiry cart with the rest of your transition fittings.

Last updated: 24 September 2026

Adaptor fxf, scj, PVC 110mm x GI.4" O/ND-P (Product Code: SLE/WDF/27) is a straight uPVC adaptor with female ends on both sides, used to join a 110 mm outside-diameter PVC pipe to a 4" nominal-diameter galvanised iron (G.I.) pipe in water-supply work. The PVC pipe is solvent-cemented into one socket and the G.I. pipe end enters the other, so the line changes material without changing direction. It is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India.

Specifications

What Is the 110mm PVC to 4 inch GI Female Adaptor Used For?

This adaptor suits the situation where the metal side ends in a pipe rather than a socket: for example an existing G.I. line that has been cut back, or a G.I. pipe coming up from a well, tank outlet or pump house. The G.I. pipe end goes into one female end and the new 110 mm PVC pipe is cemented into the other, giving a straight transition between the two systems.

Prepare the G.I. pipe end cleanly and seal the connection as the joint type requires; ask us to confirm the thread form of the G.I. end before you cut and thread pipe on site. Cement the PVC side after the G.I. side is made up, and support both pipes near the adaptor so the plastic is not bending under the weight of the metal. Work within 10 bar at 20°C.

What to Specify When Ordering

• PVC side: 110 mm outside diameter, solvent-cement pipe.
• G.I. side: a 4" nominal-diameter G.I. pipe end entering a female connection.
• Thread form: state your local G.I. thread so we can confirm the match before dispatch.
• Choose the male-threaded (fxm) adaptor instead if the G.I. side is a female socket or valve.

Supplier

ScienceLab is the trading name of Jain Scientific Equipments Private Limited, which supplies this female-ended PVC adaptor from Ambala, Haryana. The company's water-supply range is sourced for institutions, WASH programmes, contractors and dealers who prefer to handle fittings and laboratory items through one supplier. Visit the company profile to learn more.

Related Water, Sanitation & Hygiene Supplies

Other 110 mm to 4" connection options and companions:

• Adaptor fxm, scj, PVC 110mm x GI.4" O/ND-P — male-threaded version for a female G.I. socket or valve.
• Coupler PVC Socket Solvent Cement Joint Flange, 110mm x 4" — a flanged transition where the metal side is flanged.
• Tee Adaptor fxf, scj, PVC 110mm x 4" fthd O/ND-P — for a G.I. branch rather than an in-line change.
• Union Equal PVC, fxf, scj 10Bar 110mm OD-P — adds a joint on the PVC side that can be opened later.

See every fitting in Water, Sanitation & Hygiene Supplies.

Frequently Asked Questions

What does the Adaptor fxf, scj, PVC 110mm x GI.4" O/ND-P join?
The Adaptor fxf, scj, PVC 110mm x GI.4" O/ND-P joins a 110 mm outside-diameter PVC pipe to a 4" nominal-diameter G.I. pipe in a straight line. Both ends are female; the PVC side is fixed with solvent cement.

When should I choose the fxf 110mm x 4" adaptor rather than the fxm version?
Choose the fxf 110mm x 4" adaptor when the G.I. side is a pipe end that must enter the fitting. Choose the fxm version when the G.I. side is a female socket or valve that needs a male thread screwed into it.

What is the pressure rating of the 110mm x 4" fxf PVC adaptor?
The 110mm x 4" fxf PVC adaptor is rated 10 bar at 20°C and is suitable for water from 0 to 50°C. PVC's safe pressure falls in warmer water, so allow for the service temperature in your design.

Can the Adaptor fxf, scj, PVC 110mm x GI.4" O/ND-P be used for drinking water?
Check drinking-water use of the Adaptor fxf, scj, PVC 110mm x GI.4" O/ND-P with ScienceLab for your installation before buying. Include the intended service in your enquiry on the contact page, and we will tell you what can be confirmed for the supplied batch.

Who supplies the 110mm x 4" fxf PVC adaptor?
Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, Haryana, supplies the 110mm x 4" fxf PVC adaptor to schools, WASH projects, contractors and importers across India and international markets, alongside related PVC and G.I. fittings.

Request a Quote

For a quotation on product code SLE/WDF/27, send the quantity, delivery location and your G.I. thread details through the contact page, or add it to the enquiry cart.

Last updated: 24 September 2026

Reducing Coupler PVC skt scj 110x90mm-P (Product Code: SLE/WDF/28) is a straight uPVC reducing socket used to join a 110 mm outside-diameter PVC pipe to a 90 mm one in a single in-line water-supply connection. Installers use it where a main narrows along its route or meets an existing 90 mm line; both female ends are solvent-cemented and the coupler is rated 10 bar at 20°C. It is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India.

Specifications

What Is the 110 x 90mm PVC Reducing Coupler Used For?

Pipelines are often sized down as demand falls towards the far end of a network, and new work frequently has to tie into an older line of a smaller size. The reducing coupler makes that step in a straight run: the 110 mm pipe is cemented into the larger socket and the 90 mm pipe into the smaller one, with no branch and no change of direction.

Water speeds up as it passes into the smaller pipe, so designers usually place reductions where flow has already dropped. On site, clean and deburr both pipe ends, cement each socket in turn, and keep the two pipes aligned while the joints set. The fitting's rating is 10 bar at 20°C across a 0 to 50°C temperature range.

What to Specify When Ordering

• Sizes: 110 mm and 90 mm outside-diameter uPVC pipe.
• Joint type: solvent-cement pipe on both sides.
• Quantity: one per size change on the route.
• If a branch is also needed at the reduction point, specify a reducing tee instead.

Supplier

Jain Scientific Equipments Private Limited, which trades as ScienceLab in Ambala, Haryana, supplies this reducing coupler as part of its sourced water and sanitation range. Institutions and project buyers can request these fittings together with laboratory equipment on one enquiry and one set of documents. Read about the company on the ScienceLab profile.

Related Water, Sanitation & Hygiene Supplies

Fittings planned around a 110 to 90 mm change of size:

• Reducing Tee, PVC, fxf, scj, 10Bar, 110x90mm OD-P — reduces and branches at the same point.
• Coupler Reducing PP Comp, HDPE 110x90mm OD-P — the same reduction for HDPE pipe using compression joints.
• Coupler Straight/Equal PVC, skt, scj, 110mm-P — joins 110 mm lengths before the reduction.
• Union Equal PVC, fxf, scj 10Bar 110mm OD-P — a removable joint on the larger line.

The whole range is listed in Water, Sanitation & Hygiene Supplies.

Frequently Asked Questions

What sizes does the Reducing Coupler PVC skt scj 110x90mm-P connect?
The Reducing Coupler PVC skt scj 110x90mm-P connects a uPVC pipe of 110 mm outside diameter to one of 90 mm outside diameter. Both ends are female sockets joined with solvent cement in a straight line.

How is the 110 x 90mm reducing coupler different from a reducing tee?
The 110 x 90mm reducing coupler changes pipe size in a straight run with no side outlet, whereas a reducing tee also creates a branch. Use the coupler where the line simply continues at the smaller size.

What pressure is the 110 x 90mm PVC reducing coupler rated for?
The 110 x 90mm PVC reducing coupler is rated 10 bar at 20°C and suits water from 0 to 50°C. Since PVC carries less pressure as temperature rises, the working pressure should be checked against actual service conditions.

Is the Reducing Coupler PVC skt scj 110x90mm-P suitable for drinking water?
Please confirm with us whether the Reducing Coupler PVC skt scj 110x90mm-P suits your drinking-water application before ordering. Mention the intended use when you enquire through the contact page, and ask what documentation is available for the batch you are offered.

Who supplies the 110 x 90mm PVC reducing coupler?
Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, Haryana, supplies the 110 x 90mm PVC reducing coupler to schools, WASH programmes, contractors and dealers in India and international markets, and can include it in a combined fittings quotation.

Request a Quote

Share the quantity of product code SLE/WDF/28 and your delivery location via the contact page, or add the coupler to the enquiry cart with the rest of your pipeline list.

Last updated: 24 September 2026

Coupler Straight/Equal PVC, skt, scj, 110mm-P (Product Code: SLE/WDF/29) is an equal uPVC socket coupling used to join two lengths of 110 mm outside-diameter PVC pipe end to end in pressurised water lines. It is the most frequently needed fitting on a plain-ended PVC main and is also used for repairs; both female sockets are solvent-cemented and it is rated 10 bar at 20°C. It is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India.

Specifications

What Is the 110mm PVC Straight Coupler Used For?

Pipes come in fixed lengths, so a long 110 mm main needs a joint wherever two plain pipe ends meet. The straight coupler provides it: each pipe is cemented halfway into the fitting and the line continues at full bore. It is also the standard repair part, because a damaged section can be cut out and a new piece fitted with couplers, provided the pipe can be moved enough to slide the sockets on.

Mark half the socket depth on each pipe end so both are pushed in equally, then cement one side, then the other. Keep the pipe straight and still until the joints grab, and allow the cement to cure fully before pressure testing. Buried joints should be bedded evenly so they are not carrying point loads from stones.

What to Specify When Ordering

• Pipe size: 110 mm outside-diameter uPVC on both ends.
• Quantity: roughly one coupler per plain-ended pipe length, plus spares for repairs.
• Pressure class: confirm 10 bar at 20°C matches your system design.

Supplier

ScienceLab, the trading name of Jain Scientific Equipments Private Limited in Ambala, Haryana, supplies this straight coupler within its sourced range of PVC, G.I. and HDPE fittings. Buyers who already order laboratory equipment or hygiene items from ScienceLab can add pipeline fittings to the same enquiry. Company details are on the profile page.

Related Water, Sanitation & Hygiene Supplies

Other 110 mm fittings used along the same pipeline:

• Union Equal PVC, fxf, scj 10Bar 110mm OD-P — used instead of a coupler where the joint must be openable.
• Reducing Coupler PVC skt scj 110x90mm-P — continues the line at 90 mm.
• Coupler PVC Socket Solvent Cement Joint Flange, 110mm x 4" — connects the 110 mm pipe to flanged equipment.
• Cap, female PVC, scj, 110mm OD-P — closes the end of the line.

For more items, visit Water, Sanitation & Hygiene Supplies.

Frequently Asked Questions

What is the Coupler Straight/Equal PVC, skt, scj, 110mm-P used for?
The Coupler Straight/Equal PVC, skt, scj, 110mm-P joins two 110 mm outside-diameter uPVC pipes end to end with solvent cement, extending a pipeline or repairing it after a damaged section has been cut out.

Can the 110mm PVC straight coupler be used for pipe repairs?
Yes, the 110mm PVC straight coupler is commonly used for repairs: the damaged part is cut out and a new piece is cemented in with couplers. The existing pipe must have enough movement to slide the sockets over the ends.

What pressure rating does the 110mm PVC straight coupler have?
The 110mm PVC straight coupler (Coupler Straight/Equal PVC, skt, scj, 110mm-P) is rated 10 bar at 20°C and suits water from 0 to 50°C. Warmer water reduces PVC's safe pressure, so design with the service temperature in mind.

Is the Coupler Straight/Equal PVC, skt, scj, 110mm-P suitable for drinking water?
Drinking-water suitability of the Coupler Straight/Equal PVC, skt, scj, 110mm-P should be confirmed with ScienceLab for the specific line. If your project file needs this settled, state the application in your enquiry via the contact page and ask what can be provided for the batch.

Who supplies the 110mm PVC straight coupler?
Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, Haryana, supplies the 110mm PVC straight coupler to schools, WASH programmes, contractors and dealers in India and international markets, in quantities quoted to match your pipeline length.

Request a Quote

To price product code SLE/WDF/29, send the quantity and delivery location through the contact page, or add it to the enquiry cart together with the other fittings for your main.

Last updated: 24 September 2026

Coupler PVC, skt, rrj/flange, 200mm x 8" (Product Code: SLE/WDF/30) is a uPVC flanged coupling used to connect a 200 mm outside-diameter PVC pipe to 8" nominal-diameter flanged G.I. fittings, valves or equipment on large water mains. One end is a rubber ring socket that the PVC pipe pushes into; the other is a flange that bolts to the metal side. It is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India.

Specifications

What Is the 200mm PVC Flanged Coupler Used For?

Large-bore mains usually meet valves, pump stations, meters and older metal pipework at a bolted flange. This coupling bridges the two systems: the 200 mm PVC pipe enters a rubber ring socket, so no solvent cement is used on that side, while the flange bolts to an 8" G.I. flange. Rubber ring joints also allow a little movement, which helps long mains cope with expansion and ground settlement.

Chamfer and clean the pipe spigot, apply a lubricant suitable for the rubber ring, and push the pipe home squarely without twisting the ring out of its groove. On the flange side, use a gasket between the faces and tighten the bolts evenly in a cross pattern. Confirm with us which gasket and bolt set you need, and keep service within 10 bar at 20°C.

What to Specify When Ordering

• PVC side: 200 mm outside-diameter pipe suitable for rubber ring jointing.
• Flange side: 8" nominal diameter; share your flange drilling standard so we can confirm it matches.
• Gasket, bolts and ring lubricant: say whether you need them sourced with the coupling.
• Quantity: one per flanged connection on the main.

Supplier

Jain Scientific Equipments Private Limited supplies this 200 mm flanged coupling under the ScienceLab name from Ambala, Haryana. The company sources large and small pipe fittings for water utilities, WASH programmes, institutions and contractors, and can combine them with its laboratory and hygiene ranges on one enquiry. The ScienceLab profile has more about the company.

Related Water, Sanitation & Hygiene Supplies

Items used on the same large main or at similar flanged connections:

• Elbow 90º Equal PVC, fxf, rrj, 200mm OD-P — a rubber-ring bend for the same 200 mm pipe.
• Coupler PVC Socket Solvent Cement Joint Flange, 110mm x 4" — a smaller flanged coupling for 110 mm solvent-weld pipe.
• Coupler PP Comp, HDPE 110mmxflng 4"O/ND-P — the flanged option for HDPE pipe.
• Pump Centrifugal, Diesel 50cbm/hr — pumping equipment for supply schemes; check its outlet connection before planning the fittings.

Explore the full Water, Sanitation & Hygiene Supplies range.

Frequently Asked Questions

What does the Coupler PVC, skt, rrj/flange, 200mm x 8" connect?
The Coupler PVC, skt, rrj/flange, 200mm x 8" connects a 200 mm outside-diameter PVC pipe, pushed into its rubber ring socket, to an 8" nominal-diameter flanged G.I. fitting, valve or piece of equipment bolted to its flange.

Does the 200mm rubber ring flanged coupler need solvent cement?
No. The PVC side of the 200mm rubber ring flanged coupler seals with a rubber ring, so the chamfered pipe is lubricated and pushed in rather than cemented. Solvent cement should not be used on rubber ring joints.

What pressure is the 200mm x 8" PVC flanged coupler rated for?
The 200mm x 8" PVC flanged coupler is rated 10 bar at 20°C and suits water between 0 and 50°C. PVC carries less pressure as temperature increases, so the main's design pressure should reflect the actual water temperature.

Is the Coupler PVC, skt, rrj/flange, 200mm x 8" suitable for drinking water?
Confirm with us before using the Coupler PVC, skt, rrj/flange, 200mm x 8" on a drinking-water main. Utilities and project engineers should describe the application through the contact page and ask what ScienceLab can confirm for the supplied batch.

Are gaskets and bolts included with the 200mm x 8" flanged coupler?
The product description for the 200mm x 8" flanged coupler does not list a gasket or bolt set, so please tell us through the contact page whether you need these sourced with the coupling and your flange drilling standard.

Who supplies the 200mm x 8" PVC flanged coupler?
Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, Haryana, supplies the 200mm x 8" PVC flanged coupler to water projects, contractors, institutions and dealers in India and international markets, together with matching 200 mm fittings.

Request a Quote

Send the quantity of product code SLE/WDF/30, your flange standard and delivery location through the contact page, or add it to the enquiry cart with the rest of your mains fittings.

Last updated: 24 September 2026

Elbow 90º Equal PVC, fxf, rrj, 200mm OD-P (Product Code: SLE/WDF/31) is a large-bore uPVC 90° elbow used to turn a 200 mm outside-diameter PVC water main through a right angle in buried or surface pipelines. Both ends are female rubber ring sockets, so pipes are lubricated and pushed in rather than cemented, which suits big-diameter mains laid in trenches. It is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India.

Specifications

What Is the 200mm PVC Rubber Ring Elbow Used For?

Trunk mains of 200 mm follow roads, boundaries and site layouts, and every right-angle turn needs a bend of the same size. This elbow provides that turn with push-fit rubber ring sockets, which are quicker to make in a trench than solvent joints on large pipe and tolerate small movements caused by temperature change or settlement.

Because rubber ring joints are not designed to resist being pushed apart, the water pressure at a bend creates a thrust that the joints alone should not carry. Pressurised mains therefore normally have a concrete thrust block or other restraint at each bend, sized by the system designer. Chamfer and lubricate each spigot, push it fully home, and keep the main within 10 bar at 20°C.

What to Specify When Ordering

• Pipe size: 200 mm outside-diameter PVC suited to rubber ring joints.
• Angle: this item is a 90° bend; ask us if your route needs a different angle.
• Ring lubricant: say whether you need it sourced with the fittings.
• Quantity: one per right-angle turn on the route drawing.

Supplier

This 200 mm rubber ring elbow is supplied by Jain Scientific Equipments Private Limited, the Ambala, Haryana company that trades as ScienceLab. Its sourced pipeline range covers PVC, HDPE and G.I. fittings for water schemes, and buyers can handle them on the same enquiry as laboratory or hygiene products. More on the company is on its profile page.

Related Water, Sanitation & Hygiene Supplies

Fittings for the same large main and for other pipe materials:

• Coupler PVC, skt, rrj/flange, 200mm x 8" — links the 200 mm main to flanged valves or G.I. fittings.
• Bend 90º equal fxf GI 4" ND 14 Bar — a G.I. bend for threaded metal sections.
• Elbow PP Comp, HDPE 110mmxfthd 4" O/ND-P — an elbow for HDPE pipe with a threaded outlet.
• Elbow 90º, PVC scj/fthd, 40mm x 1¼"-P — a small solvent-weld elbow for service connections off the network.

View all fittings in Water, Sanitation & Hygiene Supplies.

Frequently Asked Questions

What pipe does the Elbow 90º Equal PVC, fxf, rrj, 200mm OD-P fit?
The Elbow 90º Equal PVC, fxf, rrj, 200mm OD-P fits PVC pipe of 200 mm outside diameter on both ends. Each female end has a rubber ring seal, so the chamfered, lubricated pipe is pushed in rather than solvent-cemented.

Does the 200mm PVC rubber ring elbow need a thrust block?
On a pressurised main, the 200mm PVC rubber ring elbow normally needs a thrust block or other restraint, because rubber ring joints are not designed to hold the thrust that water pressure creates at a bend. The system designer should size it.

What pressure is the 200mm PVC rubber ring elbow rated for?
The 200mm PVC rubber ring elbow (Elbow 90º Equal PVC, fxf, rrj, 200mm OD-P) is rated 10 bar at 20°C and suits water from 0 to 50°C. Warmer water lowers PVC's safe pressure, so allow for the service temperature.

Is the Elbow 90º Equal PVC, fxf, rrj, 200mm OD-P suitable for drinking water?
Please check drinking-water suitability of the Elbow 90º Equal PVC, fxf, rrj, 200mm OD-P with us for your application first. For a utility main or tender, raise the question through the contact page when requesting a quotation, and we will state what we can confirm for the batch.

Who supplies the 200mm PVC rubber ring elbow?
Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, Haryana, supplies the 200mm PVC rubber ring elbow to water utilities, WASH programmes, contractors and dealers in India and international markets, together with other 200 mm fittings.

Request a Quote

Request a price for product code SLE/WDF/31 by sending the quantity and delivery location through the contact page, or add it to the enquiry cart with the other fittings for your main.

Last updated: 24 September 2026

Driver Sanitization Kit (Product Code: SLE/SAH/24) is a vehicle hygiene kit used to keep a driver's cab and delivery handovers clean in courier, delivery and institutional transport work. It pairs gloves, meant to be changed at every delivery, with Sterizen Sanitising Solution for touch points such as steering wheels, PDAs and door handles, so fleet operators can issue one standard kit per vehicle. It is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India.

Key Details

What Is the Driver Sanitization Kit Used For?

Delivery and transport drivers touch the same few surfaces hundreds of times a shift and then hand parcels, documents or handheld devices to customers. The kit gives them a simple routine: sanitise the steering wheel, door handles and the PDA or scanner at the start of the shift and at breaks, and put on a fresh pair of gloves for every delivery so each customer receives an item handled with clean gloves.

Use the Sterizen solution as its label directs, including any contact time before wiping, and keep the bottle closed and out of direct sun in the cab. Bag used gloves and dispose of them with general waste rather than leaving them in the vehicle. Fleet managers often keep one kit per vehicle and a small stock of refills at the depot.

What to Specify When Ordering

• Number of kits: usually one per vehicle or per driver.
• Contents check: ask us to confirm the full contents list and quantities in the kit you are quoted.
• Batch expiry: request the expiry date of the sanitising solution in the quoted batch.
• Related consumables: add spare gloves, spray or hand sanitiser if drivers will need refills.

Supplier

Jain Scientific Equipments Private Limited, which trades as ScienceLab, supplies the Driver Sanitization Kit from Ambala, Haryana. The company sources hygiene products for fleets, schools, institutions and dealers alongside its laboratory ranges, so buyers can handle several categories through one supplier. More about the company is on the ScienceLab profile page.

Related Water, Sanitation & Hygiene Supplies

Other hygiene products that complement a vehicle kit:

• Sanitization Spray — a trigger spray for touch screens, keypads and control panels.
• Hand sanitizer Alcohol >60% 500ml w. Pump — a pump bottle for the depot or driver's cab.
• Classroom Cleaning & Sanitization Kit — a kit for schools that run their own transport.
• Garbage Bags, 100 liters — for collecting used gloves and wipes at the depot.

The full hygiene and water range is in Water, Sanitation & Hygiene Supplies.

Frequently Asked Questions

What is included in the Driver Sanitization Kit?
The Driver Sanitization Kit includes gloves for changing at each delivery and Sterizen Sanitising Solution for cleaning touch points in the vehicle. The complete contents list and quantities are confirmed with each quotation, so please ask us through the contact page.

Which surfaces can the solution in the Driver Sanitization Kit be used on?
The Sterizen Sanitising Solution in the Driver Sanitization Kit is described as safe for use on all surfaces, including steering wheels, PDAs and door handles. Follow the label directions for application and any contact time before wiping.

How often should the gloves from the Driver Sanitization Kit be changed?
Gloves from the Driver Sanitization Kit should be replaced at each delivery, so every customer handover is made with a fresh pair. Used gloves should be bagged and disposed of rather than kept in the vehicle.

What is the shelf life of the Driver Sanitization Kit solution?
The shelf life of the sanitising solution in the Driver Sanitization Kit depends on the chemical, its grade and storage conditions. Ask us for the expiry date of the batch you are quoted before placing a fleet order.

Who supplies the Driver Sanitization Kit?
Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, Haryana, supplies the Driver Sanitization Kit to delivery fleets, schools, institutions and dealers in India and international markets, and can quote it with other hygiene supplies.

Can the Driver Sanitization Kit be ordered for a whole fleet?
Yes, the Driver Sanitization Kit can be quoted in fleet quantities. Tell us the number of kits, any refills you need and the delivery location through the contact page, and we will reply with pricing and availability.

Request a Quote

Request pricing for product code SLE/SAH/24 through the contact page with your kit quantity and delivery location, or add it to the enquiry cart with any other hygiene items.

Last updated: 24 September 2026

Sanitization Spray (Product Code: SLE/SAH/25) is a multi-surface disinfectant cleaner spray used to sanitise frequently touched surfaces such as touch screens, keypads and control panels in schools, labs, offices and kitchens. It comes in a handy 150 ml bottle with a lockable trigger, is perfume free and non-tainting, and is described as food-safe, supplied in packs of 12. It is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India.

Specifications

What Is the Sanitization Spray Used For?

Shared devices and controls are handled by many people in a day: lab instrument keypads, smartboard and tablet screens, lift and door buttons, photocopier panels and the fronts of kitchen appliances. This spray is intended for exactly those touch points. Because it is perfume free and non-tainting, it also suits staff rooms, canteens and food-preparation areas where a scented cleaner would be unwelcome.

For screens and electronics, spray onto a clean cloth rather than directly onto the device, then wipe; follow the label for any contact time. The trigger locks for storage and transport, and the 150 ml bottle is small enough for a desk drawer, lab bench or vehicle glovebox. Always read and follow the safety directions printed on the label.

What to Specify When Ordering

• Number of packs: the spray is supplied in packs of 12 bottles of 150 ml.
• Batch expiry: ask for the expiry date of the batch in your quotation.
• Safety information: request the label and safety data you need for your site records.
• Companion items: add hand sanitiser or cleaning kits if you are equipping classrooms or vehicles.

Supplier

ScienceLab, the trading name of Jain Scientific Equipments Private Limited in Ambala, Haryana, supplies this Sanitization Spray as part of its sourced hygiene range for schools, colleges, offices and dealers. For vendor registration, the supplying company can be identified by GSTIN 06AAECJ8618A1ZT and LEI 3358004HRD1JIVXKYX49; these are company trade registrations, not product approvals. See the company profile for more.

Related Water, Sanitation & Hygiene Supplies

Other items used in the same cleaning routine:

• Universal Disinfectant Spray — another disinfectant spray option for comparison.
• Classroom Cleaning & Sanitization Kit — a kit for routine classroom cleaning.
• Driver Sanitization Kit — gloves and sanitising solution for vehicles.
• Hand sanitizer Alcohol >60% 500ml w. Pump — for hands, as the spray is meant for surfaces.

Browse all hygiene products in Water, Sanitation & Hygiene Supplies.

Frequently Asked Questions

What size and pack does the Sanitization Spray come in?
The Sanitization Spray comes in a 150 ml bottle with a lockable trigger, supplied in a pack of 12. Quote requests should state the number of packs needed so pricing can be calculated for the full quantity.

What surfaces is the Sanitization Spray intended for?
The Sanitization Spray is intended for frequently touched surfaces such as control panels, touch screens, keypads, button controls and appliance surfaces. For electronics, spray onto a cloth first and follow the label directions.

What does the Sanitization Spray kill?
The product description states that the Sanitization Spray kills 99.9% of bacteria, including MRSA, E. coli, Listeria and Salmonella. Use it exactly as the label directs, including any contact time, for the stated performance.

Can the Sanitization Spray be used in food areas?
The Sanitization Spray is described as food-safe, perfume free and non-tainting, so it is suited to canteens, staff rooms and food-preparation surfaces. Follow the label for any rinsing instructions on food-contact surfaces.

What is the shelf life of the Sanitization Spray?
The shelf life of the Sanitization Spray depends on the chemical, its grade and storage conditions. Ask us through the contact page for the expiry date of the batch you are quoted.

Who supplies the Sanitization Spray?
Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, Haryana, supplies the Sanitization Spray to schools, institutions, offices and dealers in India and international markets, and can quote it together with other hygiene supplies.

Request a Quote

For pricing on product code SLE/SAH/25, send the number of packs and delivery location through the contact page, or add the spray to the enquiry cart.

Last updated: 24 September 2026

Alcohol Hand Sanitizer Gel (Product Code: SLE/SAH/26) is a ready-to-use alcohol hand gel used to clean hands without soap or water in classrooms, laboratories, offices and clinics. It contains more than 70% alcohol, comes in a 500 ml pump bottle that dispenses a measured dose, and is described as leaving hands clean and moisturised. It is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India.

Specifications

What Is the Alcohol Hand Sanitizer Gel Used For?

Hand gel fills the gap where a wash basin is not close by: at a classroom door, a lab entrance, a reception desk, a school bus or a canteen queue. One press of the pump gives a measured amount, and the gel acts as soon as it touches the skin, so users can clean their hands in the time it takes to walk in. The product description also lists hygienic hand antisepsis and pre-surgical hand preparation among its uses; clinical users should follow their own facility's hand-hygiene protocol.

Rub the gel over all parts of both hands, including between the fingers, backs of hands and thumbs, until dry. Visibly dirty or greasy hands should still be washed with soap and water. Because the gel is high in alcohol, keep the bottle away from flames and Bunsen burners in science labs and store it closed, away from heat and direct sun.

What to Specify When Ordering

• Number of 500 ml pump bottles, for example one per classroom, lab or entrance.
• Batch expiry: ask for the expiry date of the batch you are quoted.
• Smaller sizes: say if you also need pocket or desk bottles for staff.

Supplier

Jain Scientific Equipments Private Limited supplies this Alcohol Hand Sanitizer Gel under its ScienceLab trading name from Ambala, Haryana. Schools and institutions that source lab consumables from ScienceLab can include hand-hygiene products in the same order, keeping purchasing for labs and campus hygiene under one supplier. Read more on the ScienceLab profile page.

Related Water, Sanitation & Hygiene Supplies

Other hand-hygiene options for a school or workplace:

• Hand sanitizer Alcohol >60% 500ml w. Pump — another 500 ml pump-bottle sanitiser for comparison.
• Alcohol Hand Sanitizer, 150ml — a smaller bottle for desks, bags and vehicles.
• Hand Wash Station — for soap-and-water washing where hands are visibly dirty.
• Soap Toilet Bar Approx. 100-110g Wrapped — soap for wash basins and hand-wash points.

See the complete range in Water, Sanitation & Hygiene Supplies.

Frequently Asked Questions

How much alcohol does the Alcohol Hand Sanitizer Gel contain?
The Alcohol Hand Sanitizer Gel contains more than 70% alcohol. It is a ready-to-use formula, so it is applied straight from the pump bottle without dilution, soap or water.

What size is the Alcohol Hand Sanitizer Gel bottle?
The Alcohol Hand Sanitizer Gel comes in a 500 ml pump bottle that dispenses a measured dose with each press, which helps limit waste in busy classrooms, labs and reception areas.

Can the Alcohol Hand Sanitizer Gel replace hand washing?
The Alcohol Hand Sanitizer Gel is an alternative to soap and water when a basin is not available, but hands that are visibly dirty or greasy should still be washed with soap and water first.

Is the Alcohol Hand Sanitizer Gel safe to use near Bunsen burners?
No. The Alcohol Hand Sanitizer Gel is high in alcohol and flammable until it has dried, so users should rub hands until completely dry and keep the bottle away from Bunsen burners, spirit lamps and other flames.

What is the shelf life of the Alcohol Hand Sanitizer Gel?
The shelf life of the Alcohol Hand Sanitizer Gel depends on the chemical, its grade and storage conditions. Ask us through the contact page for the expiry date of the batch you are quoted.

Who supplies the Alcohol Hand Sanitizer Gel?
Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, Haryana, supplies the Alcohol Hand Sanitizer Gel to schools, colleges, institutions and dealers in India and international markets, and can quote it with other hygiene and laboratory supplies.

Request a Quote

Send the number of 500 ml bottles of product code SLE/SAH/26 and your delivery location through the contact page, or add the gel to the enquiry cart.

Last updated: 24 September 2026

Alcohol Hand Sanitizer, 150ml (Product Code: SLE/SAH/27) is an alcohol-based hand sanitiser spray used to disinfect hands without soap or water in classrooms, laboratories, offices and other shared spaces. Its 80% alcohol, no-rinse formula dries quickly, and the 150 ml bottles come 12 to a pack, a handy size for desks, bags and lab benches. It is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India, as part of its school and lab consumables range.

Specifications

What Is the 150ml Alcohol Hand Sanitizer Used For?

Teachers and lab staff keep this spray at classroom doors, on practical benches and in staff rooms so that students can clean their hands before and after handling shared apparatus, specimens or books. Spray enough onto the palms to wet both hands, then rub it over the backs of the hands, between the fingers and around the nails until the skin is dry. No towel or rinse is needed, which keeps queues short when a whole class changes rooms.

Alcohol sanitiser is a companion to soap and water, not a replacement: when hands are visibly dirty or greasy, wash them first. Because the formula is alcohol based, let hands dry completely before lighting a Bunsen burner and store bottles away from heat and flames. Stocking small bottles like these is a simple, low-cost part of any school laboratory setup in India.

Supplier

Jain Scientific Equipments Private Limited trades under the name ScienceLab and supplies hygiene products such as this 150 ml sanitiser spray alongside its laboratory equipment, so schools, colleges and distributors can combine both on one purchase order. For vendor registration, the supplying company is listed under CIN U29309HR2020PTC087597 and GSTIN 06AAECJ8618A1ZT. Learn more on our company profile.

Related Water, Sanitation & Hygiene Supplies

These products are often ordered with the 150 ml sanitiser spray to cover hand and surface hygiene across a school or lab:

• Alcohol Hand Sanitizer Gel — a gel alternative for users who prefer a rub-in texture to a spray.
• Hand sanitizer Alcohol >60% 500ml w. Pump — a larger pump bottle for entrances and reception desks.
• Hand Wash Station — soap-and-water washing where there is no plumbing, for hands that are visibly soiled.
• Universal Disinfectant Wipes — for desks and door handles, since hand sanitiser is meant for skin only.

See the complete Water, Sanitation & Hygiene Supplies range for soap, cleaning and sanitation items.

Frequently Asked Questions

What type of sanitiser is the Alcohol Hand Sanitizer, 150ml?
The Alcohol Hand Sanitizer, 150ml is an 80% alcohol formulation in spray form, used as a no-rinse hand rub for hand disinfection. If you need the full ingredient list for the batch being quoted, please ask us through the contact page before ordering.

How many bottles come in one pack?
One pack of the Alcohol Hand Sanitizer, 150ml holds 12 bottles, each containing 150 ml of spray. Order as many packs as you need to place a bottle in every classroom, lab bench or staff area, and mention the total in your enquiry.

Do hands need to be rinsed after using it?
No rinsing is needed with the Alcohol Hand Sanitizer, 150ml. Spray it onto the palms, rub it over all parts of both hands until dry, and the quick-drying formula leaves the skin feeling clean, fresh and lightly scented.

Is it safe to use near a Bunsen burner?
The Alcohol Hand Sanitizer, 150ml contains alcohol and is flammable while wet, so hands must be completely dry before anyone lights a burner or works near a flame. Store the bottles away from heat sources, open flames and direct sunlight.

What is the shelf life of this hand sanitiser?
Shelf life of the Alcohol Hand Sanitizer, 150ml depends on the chemical, its grade and storage conditions, so no fixed period is given here. Ask us for the expiry date of the batch you are quoted, and keep bottles tightly closed in a cool place.

Who supplies the Alcohol Hand Sanitizer, 150ml?
The Alcohol Hand Sanitizer, 150ml is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India, which provides hygiene products together with laboratory equipment to schools, colleges, institutions and distributors in India and international markets.

What should I include in a quotation request?
For a quotation on the Alcohol Hand Sanitizer, 150ml, state the number of 12-bottle packs, the delivery location and any other hygiene items you want in the same shipment. Send these details through our contact page or add the product to the enquiry cart.

Request a Quote

To request a price for the Alcohol Hand Sanitizer, 150ml, send your quantity and delivery details through our contact page, or add it to the enquiry cart together with other supplies you need. We respond to schools, colleges, institutions and distributors in India and international markets.

Last updated: 24 September 2026

Classroom Cleaning & Sanitization Kit (Product Code: SLE/SAH/28) is a bulk hygiene kit used to clean and disinfect hard surfaces and hands across a school, with everything carried on its own trolley. It combines disinfectant wipes, disinfectant sprays and alcohol hand gel, so caretakers and teachers can service several classrooms and labs in one round. It is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India, for school lab equipment bulk supply and institutional hygiene programmes.

Key Details

What Is a Classroom Cleaning Kit Used For?

The kit is built for a daily hygiene round: the trolley is wheeled from room to room, the spray and wipes are used on desks, door handles, light switches and shared apparatus, and a bottle of hand gel is left at each classroom or lab entrance. Keeping all the products on one two-shelf trolley means nothing has to be fetched from a store room between rooms.

A practical routine is to spray or wipe high-touch surfaces between lessons, work from cleaner areas towards dirtier ones, and keep the chemicals on the lower shelf, out of reach of younger pupils. Schools planning a new school laboratory setup in India often add a kit like this so that practical benches can be wiped down after every class.

What to Specify When Ordering

• The number of complete kits, each with 1 trolley, 10 packs of wipes, 12 sprays and 12 hand gels.
• Any extra wipes, sprays or hand gel you want as separate refill stock.
• The delivery address and whether the goods go to one campus or several schools.

Supplier

This kit is sourced and supplied by Jain Scientific Equipments Private Limited, the company behind the ScienceLab name. Because the same company supplies laboratory trolleys, apparatus and hygiene consumables, a school can place a single order for its cleaning kit and its science equipment. More about the business is on our company profile.

Related Water, Sanitation & Hygiene Supplies

Use these items to restock the kit or extend it to more rooms:

• Universal Disinfectant Wipes — refill packs for quick wipe-downs of desks and handles.
• Universal Disinfectant Spray — extra spray bottles for larger surfaces and bench tops.
• Alcohol Hand Sanitizer Gel — replacement hand gel for classroom entrances.
• Laboratory Trolley – 2 Shelf — an additional trolley if cleaning rounds are split between staff.
• Mop Bucket with Strainer — for floors, which the wipes and spray are not intended to cover.

Browse all Water, Sanitation & Hygiene Supplies for more cleaning and sanitation products.

Frequently Asked Questions

What is included in the Classroom Cleaning & Sanitization Kit?
The Classroom Cleaning & Sanitization Kit contains one 2-shelf laboratory trolley, 10 packs of Universal Disinfectant Wipes (200 per pack), 12 bottles of Universal Disinfectant Spray (1 litre each) and 12 bottles of Alcohol Hand Sanitiser Gel (500 ml each).

What is the trolley for?
The trolley in the Classroom Cleaning & Sanitization Kit stores the wipes, sprays and hand gel and lets staff move them around the school. Its two shelves allow cleaning products and hand gel to be kept apart during a cleaning round.

Can the wipes, spray and gel be reordered separately?
Yes. The wipes, spray and hand gel used in the Classroom Cleaning & Sanitization Kit are also listed as individual products, so you can ask us for refill quantities without buying another trolley. State the items and quantities in your enquiry.

What surfaces is the kit meant for?
The Classroom Cleaning & Sanitization Kit is intended for cleaning and disinfecting hard surfaces such as desks, bench tops and handles, and for hand hygiene with the gel. For a particular surface material, check the product label or ask us before use.

What is the shelf life of the products in the kit?
Shelf life of the wipes, spray and gel in the Classroom Cleaning & Sanitization Kit depends on the chemical, its grade and storage conditions. Ask us for the expiry date of the batch you are quoted, and store the products closed and away from heat.

Who supplies this cleaning kit?
The Classroom Cleaning & Sanitization Kit is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India, which provides hygiene products and laboratory equipment to schools, colleges, institutions and distributors in India and international markets.

Request a Quote

For a quotation on the Classroom Cleaning & Sanitization Kit, tell us how many kits and any refill stock you need through our contact page, or add the kit to the enquiry cart. We supply schools, colleges, institutions and distributors in India and international markets.

Last updated: 24 September 2026

Hand Wash Station (Product Code: SLE/SAH/29) is a self-contained, portable sink unit used to wash hands with soap and water in places that have no plumbing or electricity, such as school entrances, playgrounds, canteens and outdoor events. Its easy-fill 45 L tank supplies up to 225 hand washes of 20 seconds, and a foot-operated tap keeps the water supply hands-free. It is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India.

Specifications

What Is a Portable Hand Wash Station Used For?

Washing with soap and running water is the standard way to remove dirt and germs from hands, but many sites lack a sink where people actually gather. This unit brings a complete wash point to a school gate, a sports ground, a temporary classroom or a field laboratory: users press the foot pedal for water, take soap from the dispenser, dry their hands with a paper towel and drop it in the bin, without touching the tap.

In daily use, refill the 45 L tank before it runs dry, empty the 25 L grey water drum each time the tank is refilled so it never overflows, and restock soap and towels at the same visit. Because it needs no plumber or electrician, the station can be moved as timetables change, which makes it a useful addition to any school laboratory setup in India where lab sinks are few.

What to Specify When Ordering

• The number of stations and where each will stand (indoors or outdoors).
• Whether you also need soap and paper towel stock; the dispensers are included, so ask us about consumables.
• Site access for a unit measuring 620 x 1630 x 560 mm and weighing 25 kg empty.

Supplier

ScienceLab is the trading name of Jain Scientific Equipments Private Limited, which supplies this hand wash station to schools, colleges, offices and institutions together with its laboratory and hygiene range. Placing sanitation items and lab supplies with one supplier keeps delivery and paperwork simple. Find out more on our company profile.

Related Water, Sanitation & Hygiene Supplies

These products keep a hand wash point stocked and clean:

• Hand Wash — hand wash to keep soap available at the station.
• Garbage Bags, 100 liters — for collecting and disposing of used paper towels from the bin.
• Alcohol Hand Sanitizer, 150ml — spray sanitiser for moments when the station is not within reach.
• Universal Disinfectant Wipes — for wiping down the dispensers and other touch points on the unit.

More products are listed under Water, Sanitation & Hygiene Supplies.

Frequently Asked Questions

Does the Hand Wash Station need plumbing or electricity?
No. The Hand Wash Station is a self-contained unit that needs no plumbing or electrics. Water comes from its own 45 L tank through a foot-operated tap, and used water drains into a removable collection drum, so it can be placed almost anywhere.

How many hand washes does one tank provide?
One full 45 L tank on the Hand Wash Station provides enough water for up to 225 hand washes of 20 seconds each. Busy sites should plan refills and grey water emptying according to how many people use the station each day.

What happens to the used water?
Used water from the Hand Wash Station drains into a removable 25 L grey/waste water collection drum. Take the drum out and empty it into a suitable drain whenever the clean tank is refilled, so that it does not overflow.

What comes with the Hand Wash Station?
Each Hand Wash Station comes with a soap dispenser, a paper towel dispenser, a 25 L grey water collection drum and a waste bin, giving users everything needed to wash, dry and dispose of towels at one point.

How large and heavy is the unit?
The Hand Wash Station measures 620 x 1630 x 560 mm (W x H x D) and weighs 25 kg without water and consumables. It is made from 70% recycled plastic, which keeps it light enough to reposition when empty.

Can it be used outdoors?
Yes. The Hand Wash Station is suitable for external and outdoor environments as well as indoor high-footfall areas such as corridors, canteens and entrances, which makes it practical for schools, events and temporary sites.

Who supplies the Hand Wash Station?
The Hand Wash Station is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India, to schools, colleges, institutions and distributors in India and international markets. Send your quantity and delivery location through the contact page for a quotation.

Request a Quote

To get a price for the Hand Wash Station, share the number of units and the delivery site through our contact page, or add it to the enquiry cart with any other hygiene or laboratory items you need.

Last updated: 24 September 2026

Sterilising Fluid (Product Code: SLE/SAH/30) is a concentrated sterilising liquid used to disinfect protective eyewear and other reusable equipment by soaking in a diluted solution in schools, laboratories and workshops. One 30 ml capful in 5 litres of water makes a 0.6% soaking solution that needs no rinsing, and the fluid is offered in 500 ml, 1000 ml and 5 L bottles. It is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India.

Specifications

What Is Sterilising Fluid Used For?

Goggles, face shields and small reusable items are passed from student to student during practical classes, so they need disinfecting between groups. Fill a clean container with 5 litres of water, add one 30 ml capful of Sterilising Fluid, fully immerse the items for 15 minutes, then lift them out and let them air-dry; no rinse is required.

A single batch of solution stays effective for up to 24 hours, so labs can prepare it at the start of the day and discard it at the end. Label the soaking container, keep the concentrate capped, and never mix it with other cleaning chemicals. This is a straightforward routine for the shared safety goggles that schools across India keep in their practical rooms.

What to Specify When Ordering

• Bottle size: 500 ml, 1000 ml or 5 L.
• Number of bottles, based on how many 5-litre batches you prepare each week.
• Whether you would prefer pre-measured tablets instead of liquid concentrate.

Supplier

Jain Scientific Equipments Private Limited, known to customers as ScienceLab, sources and supplies this sterilising fluid for schools, colleges and training laboratories along with safety eyewear and lab apparatus. Buyers can therefore order the disinfectant and the equipment it protects from the same supplier. Visit our company profile for background on the company.

Related Water, Sanitation & Hygiene Supplies

Items that are used with Sterilising Fluid, or chosen as alternatives:

• Sterilising Tablets — pre-measured tablets for the same 5-litre soaking method, with no measuring needed.
• Safety Goggles — the kind of shared protective eyewear this fluid is meant to disinfect.
• Premium Safety Spectacles — eye protection that can be soaked between users.
• Universal Disinfectant Spray — for benches and larger surfaces that cannot be immersed.

Explore the full Water, Sanitation & Hygiene Supplies category for more disinfection products.

Frequently Asked Questions

How do I dilute Sterilising Fluid?
Add 30 ml of Sterilising Fluid, which is one capful, to 5 litres of water to make a 0.6% solution. Soak the equipment fully for 15 minutes, then remove it and leave it to dry; the solution does not need to be rinsed off.

How long does a prepared solution stay effective?
A solution made with Sterilising Fluid remains effective for up to 24 hours. Prepare a fresh batch each day and discard the old solution, rather than topping it up, so the dilution stays correct.

Which germs is Sterilising Fluid effective against?
According to its product specification, Sterilising Fluid kills 99.9% of germs, including bacteria, fungi and viruses, and is effective on Rotavirus, Coronavirus, MRSA and swine flu. Follow the stated dilution and 15-minute soak time for these results.

What bottle sizes are available?
Sterilising Fluid is available in 500 ml, 1000 ml and 5 L bottles. Smaller bottles suit a single lab, while the 5 L size is convenient for schools or colleges that disinfect goggles for many classes every day.

What is the shelf life of Sterilising Fluid?
The shelf life of Sterilising Fluid depends on the chemical, its grade and storage conditions, so we do not state a fixed period. Ask us for the expiry date of the batch you are quoted, and keep bottles capped and out of direct sunlight.

Who supplies Sterilising Fluid?
Sterilising Fluid is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India, to schools, colleges, laboratories and distributors in India and international markets, often together with safety eyewear and other laboratory supplies.

Request a Quote

Tell us the bottle size and quantity of Sterilising Fluid you need through our contact page, or add it to the enquiry cart alongside eyewear or other items, and we will prepare a quotation.

Last updated: 24 September 2026

Sterilising Tablets (Product Code: SLE/SAH/31) are pre-measured sterilising tablets used to prepare a soaking solution that disinfects protective eyewear and reusable equipment in labs, workshops and classrooms. Each tablet is dissolved in 5 litres of water, which removes any need to measure liquid, and a pack holds 28 tablets for storage in a drawer or first-aid cupboard. They are supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India.

Specifications

What Are Sterilising Tablets Used For?

Tablets suit places where measuring a liquid concentrate is inconvenient, for example a workshop store, a field trip kit or a science department without a measuring jug to spare. Drop one tablet into 5 litres of water, allow it to dissolve, immerse the goggles or equipment for 15 minutes, and then set them aside to dry without rinsing.

Because every tablet is the same size, each batch has the same strength regardless of who prepares it, which helps when student helpers or lab assistants take turns. Make a new batch within 24 hours, handle tablets with dry hands, and keep the pack sealed. Stocking a compact pack like this is an easy step for any lab consumables supplier or school purchasing officer in India planning eye-protection hygiene.

Supplier

Sterilising Tablets are supplied by Jain Scientific Equipments Private Limited, which trades as ScienceLab and serves schools, colleges and distributors with hygiene products and laboratory equipment. For import and tax paperwork, the supplying company's Importer-Exporter Code is AAECJ8618A (DGFT) and its GSTIN is 06AAECJ8618A1ZT. Read more on our company profile.

Related Water, Sanitation & Hygiene Supplies

Products that pair with Sterilising Tablets in an eye-protection hygiene routine:

• Sterilising Fluid — a liquid concentrate in 500 ml to 5 L bottles for labs that prefer to measure by capful.
• Safety Goggles — shared goggles that can be soaked between classes.
• Premium Safety Spectacles — lighter eye protection that also benefits from regular disinfection.
• Universal Disinfectant Wipes — for wiping the storage box or bench where cleaned eyewear is kept.

View the whole Water, Sanitation & Hygiene Supplies range.

Frequently Asked Questions

How many Sterilising Tablets are in a pack?
A pack of Sterilising Tablets contains 28 tablets. Each tablet is dissolved in 5 litres of water to make one batch of soaking solution, so the pack count tells you how many separate batches can be prepared.

How are Sterilising Tablets used?
Dissolve one of the Sterilising Tablets in 5 litres of water, immerse the eyewear or equipment for 15 minutes, then remove it and leave it to dry. No rinsing is needed, and the prepared solution remains effective for up to 24 hours.

Should I choose tablets or Sterilising Fluid?
Sterilising Tablets give a pre-measured dose with nothing to pour, which suits small stores, travel kits and occasional users. Sterilising Fluid is a liquid measured by the capful and comes in larger bottles for frequent, high-volume use. Both use the same 15-minute soak.

What germs do Sterilising Tablets act on?
The product specification states that Sterilising Tablets kill 99.9% of germs, including bacteria, fungi and viruses, and are effective on Rotavirus, Coronavirus, MRSA and swine flu, when used at the stated strength and soak time.

What is the shelf life of Sterilising Tablets?
Shelf life of Sterilising Tablets depends on the chemical, its grade and storage conditions, so it is not fixed on this page. Ask us for the expiry date of the batch you are quoted, and keep the pack closed in a cool, dry place.

Who supplies Sterilising Tablets?
Sterilising Tablets are supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India, to schools, colleges, laboratories and distributors in India and international markets. Send your required number of packs through the contact page for a quotation.

Request a Quote

To order Sterilising Tablets, tell us the number of 28-tablet packs and your delivery address via our contact page, or place them in the enquiry cart with your other lab and hygiene items.

Last updated: 24 September 2026

Desk Pad (Product Code: SLE/SAH/32) is a low-maintenance desk covering, described in its product specification as antiviral and self-cleaning, used on shared desks and tables in schools, offices and reception areas. The material is embedded with silver particles, weighs 510 g/m², and comes as large 800 x 500 mm pads, two per pack, that can be cut to fit. It is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India.

Specifications

What Is the Desk Pad Used For?

Desks in computer rooms, libraries, exam halls and staff rooms are touched by many people each day. The Desk Pad is fixed over the writing area so that the part people actually lean on and handle is covered by it; according to its product specification, the surface is antiviral and the embedded silver particles act on viruses soon after it is touched. It is presented as a robust alternative to repeated antiviral spraying of the same desk.

For a neat fit, clean and dry the desk first, lay the pad in position, trim any overhang with sharp scissors, and then press it down firmly. The pad still needs ordinary dusting and wiping of spills, and the rest of the desk should stay in the normal cleaning routine. Schools looking for educational laboratory equipment in India can add these pads to shared benches in computer and project rooms at the same time.

What to Specify When Ordering

• Number of desks to cover, with each pack supplying two 800 x 500 mm pads.
• Desk surface sizes, so you can plan how much trimming is needed.
• Whether you also need matching door handle wraps or door push panels for the same rooms.

Supplier

Jain Scientific Equipments Private Limited, which trades as ScienceLab, sources this silver-embedded desk covering for schools, colleges and offices as part of its hygiene and laboratory supply range. Institutions can order desk pads together with classroom and lab equipment on one quotation. See our company profile for more about the company.

Related Water, Sanitation & Hygiene Supplies

Other touch-point and cleaning products that work alongside the Desk Pad:

• Door Handle Wrap — the same kind of touch-point covering, in strips for door handles.
• Door Push Panel — small panels for the push plates of classroom and washroom doors.
• Universal Disinfectant Wipes — for wiping spills and surfaces that are not covered by pads.
• Classroom Cleaning & Sanitization Kit — a trolley kit for daily cleaning rounds across the school.

Browse the complete Water, Sanitation & Hygiene Supplies range.

Frequently Asked Questions

What size is the Desk Pad and how many come in a pack?
Each Desk Pad measures 800 mm x 500 mm, described as the large size, and the product is sold in a pack of 2. The lightweight material weighs 510 g/m², so it sits flat on a desk without adding bulk.

Can the Desk Pad be cut to fit my desks?
Yes. The Desk Pad material can be cut to fit almost any shape or size of surface, so it can be trimmed for smaller desks, curved tables or counters. Measure carefully and cut with sharp scissors for a clean edge before fixing it down.

What does the product specification say about the Desk Pad and viruses?
The Desk Pad is embedded with silver particles, and its product specification states that these give antiviral protection. The specification also states that it protects users from up to 99.5% of viruses, including Covid 19, acting on viruses on the surface after it has been touched.

Does the Desk Pad replace normal cleaning?
The product specification describes the Desk Pad as a self-cleaning, low-maintenance alternative to antiviral sprays, but dust, ink and spills should still be wiped away as normal. Follow your institution's routine cleaning schedule for the rest of the desk and room.

What fire classification does the material have?
The Desk Pad material is listed with an M1 fire classification in its product specification. If your building rules require supporting documents for the classification, please ask us before placing an order.

Who supplies the Desk Pad?
The Desk Pad is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India, to schools, colleges, offices and distributors in India and international markets. Contact us with the number of packs you need for a quotation.

Request a Quote

Send the number of Desk Pad packs and your delivery location through our contact page, or add the product to the enquiry cart with any door wraps or panels, and we will send a quotation.

Last updated: 24 September 2026

Door Handle Wrap (Product Code: SLE/SAH/33) is a silver-embedded surface covering used on door handles, trolley handles and similar high-traffic contact points in schools, hospitals, shops and offices; its product specification describes the covered surface as antiviral and antibacterial. It comes as 300 mm x 75 mm strips, ten to a pack, that are wrapped around and adhered to the handle. It is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India.

Specifications

What Is a Door Handle Wrap Used For?

A door handle is one of the few surfaces that almost everyone in a building touches, which makes classroom, laboratory, washroom and staff-room doors a common route for germs to pass between people. The grip area is wrapped in this covering, which the product specification describes as giving an antiviral and antibacterial surface, and the same strips can be used on trolley handles in canteens, libraries and stores.

Before fitting, clean and dry the handle so the wrap adheres well, then wind the strip around the part people hold and press the ends down firmly. Check the wraps during routine cleaning rounds and replace any that lift or tear. Facilities teams sourcing lab consumables and hygiene items together often fit wraps on every door of a science block in one visit.

What to Specify When Ordering

• The number of handles to cover; each pack contains 10 wraps of 300 x 75 mm.
• The type of handles (lever handles, pull handles or trolley handles) so we can discuss suitability.
• Whether flat door push panels or desk pads are needed for the same rooms.

Supplier

ScienceLab, the trading name of Jain Scientific Equipments Private Limited, supplies Door Handle Wrap packs to schools, colleges, hospitals and offices along with its laboratory and hygiene products. Ordering touch-point coverings with other supplies means one supplier handles the full delivery. More information is on our company profile.

Related Water, Sanitation & Hygiene Supplies

These products cover the other surfaces around a doorway or classroom:

• Door Push Panel — flat panels for doors that are pushed open rather than pulled by a handle.
• Desk Pad — larger sheets of the same touch-point covering, sized for shared desks and counters.
• Universal Disinfectant Spray — for cleaning door plates, frames and other hard surfaces.
• Alcohol Hand Sanitizer, 150ml — hand sanitiser to place beside busy doors.

See all products in Water, Sanitation & Hygiene Supplies.

Frequently Asked Questions

What size is the Door Handle Wrap?
Each Door Handle Wrap measures 300 mm x 75 mm and the product is sold in packs of 10. The lightweight material weighs 510 g/m², making it easy to wrap snugly around the grip area of most door and trolley handles.

Where can the Door Handle Wrap be fitted?
The Door Handle Wrap is designed for high-traffic contact points such as door handles and shopping trolleys, and it can be adhered to almost any surface. Clean and dry the handle before fitting so the wrap stays firmly in place.

What protection does the specification state for the Door Handle Wrap?
The Door Handle Wrap is embedded with silver particles, which its product specification states give the handle an antiviral and antibacterial surface. The specification also states protection from up to 99.5% of viruses, including Covid 19, on the covered area after it has been touched.

Do handles still need cleaning after wrapping?
The product specification describes the Door Handle Wrap as a self-cleaning, low-maintenance covering intended as an alternative to antiviral sprays on the handle itself. Visible dirt should still be wiped off, and the door plate, frame and surrounding areas should stay in your normal cleaning routine.

What fire classification is stated for the wrap?
The Door Handle Wrap material carries an M1 fire classification according to its product specification. If your building or safety officer needs documentation for this, ask us before ordering so we can advise.

Who supplies the Door Handle Wrap?
The Door Handle Wrap is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India, to schools, colleges, hospitals, offices and distributors in India and international markets. Share the number of packs you need through the contact page for a quotation.

Request a Quote

For a price on the Door Handle Wrap, send us the number of packs and your location through the contact page, or add it to the enquiry cart with push panels, desk pads or other supplies.

Last updated: 24 September 2026

Door Push Panel (Product Code: SLE/SAH/34) is a small surface panel, described in its product specification as antiviral and antibacterial, used to cover the area of a door that people push with their palms in schools, clinics, canteens and offices. Each panel is 100 x 230 mm, embedded with silver particles and can be cut to fit, with ten panels in every pack. It is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India.

Specifications

What Is a Door Push Panel Used For?

Swing doors on corridors, toilets, dining halls and laboratories are usually opened by a flat-handed push at roughly the same spot, so that spot collects contact from everyone who passes. A push panel fixed there covers the touched area with a material that the product specification describes as antiviral and antibacterial. The panel can also be trimmed and used on light-switch surrounds, lift-button areas or cupboard doors that are pushed rather than pulled.

Mark the height where hands meet the door, clean and dry the area, then press the panel firmly into place, cutting it first if the door rail is narrow. Replace panels that peel or become damaged. Estates teams equipping labs and classrooms through a laboratory equipment supplier in India can order push panels for every door in the same delivery.

Supplier

Door Push Panel packs are supplied by Jain Scientific Equipments Private Limited, a company that does business as ScienceLab and supplies schools, colleges, healthcare facilities and offices with hygiene and laboratory products. Buyers can bundle panels with other touch-point coverings on a single order. Our company profile gives further details.

Related Water, Sanitation & Hygiene Supplies

Products that complete a hygienic doorway and classroom:

• Door Handle Wrap — wrap-around strips for doors that are opened by a handle.
• Desk Pad — large sheets of desk covering for the desks inside the room.
• Universal Disinfectant Wipes — for the rest of the door surface, frames and switches.
• Hand Wash Station — a portable wash point for entrances without a sink.

More items are listed in Water, Sanitation & Hygiene Supplies.

Frequently Asked Questions

What are the dimensions of the Door Push Panel?
Each Door Push Panel measures 100 x 230 mm, described as the small size, and is sold in packs of 10. The material weighs 510 g/m², so the panels are light and sit flat against the face of a door.

Can the Door Push Panel be trimmed?
Yes. The Door Push Panel material can be cut to fit almost any shape or size of surface, so a panel can be narrowed for slim door rails or shaped around a lock or sign before it is adhered.

How is a Door Push Panel different from a Door Handle Wrap?
A Door Push Panel is a flat 100 x 230 mm piece for the part of a door pushed with the palm, while the Door Handle Wrap is a narrow strip wound around the grip of a handle. Many buildings use both.

What does the product specification say about the Door Push Panel's protection?
The Door Push Panel is embedded with silver particles which, according to its product specification, create an antiviral and antibacterial surface. The same specification states protection for users from up to 99.5% of viruses, including Covid 19, on the covered area after contact.

What fire classification does the panel carry?
The Door Push Panel material is listed with an M1 fire classification in its product specification. If a fire safety officer needs supporting paperwork, please ask us before ordering so we can confirm what is available.

Who supplies the Door Push Panel?
The Door Push Panel is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India, to schools, colleges, clinics, offices and distributors in India and international markets. Send the number of doors you need to cover for a quotation.

Request a Quote

To request pricing for the Door Push Panel, tell us how many packs of 10 you need through our contact page, or add the product to the enquiry cart together with handle wraps or desk pads.

Last updated: 24 September 2026

Universal Disinfectant Spray (Product Code: SLE/SAH/35) is a ready-to-use surface disinfectant used to clean and disinfect hard surfaces in healthcare, school, laboratory and other hygiene-critical settings. Its neutral pH formula needs no mixing or dilution and is suitable for rubber, plastic, metal, acrylic glass, PVC and anodised aluminium, supplied in a 1 litre spray bottle. It is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India.

Specifications

What Is Universal Disinfectant Spray Used For?

This spray is meant for the hard surfaces that get handled all day: bench tops, trays, plastic apparatus, metal stands, rubber mats, acrylic screens and PVC-covered furniture. Because it arrives ready to use, staff simply spray the surface, leave it wet for the contact time, and wipe it with a clean cloth. There is no concentrate to measure, so the strength is the same whoever does the cleaning.

Clean away visible dirt before disinfecting, work in a ventilated space, and never mix the spray with bleach or other cleaners. The neutral pH and the fact that it is gentler to handle than chlorine make it practical for school labs, sick bays and clinics. Colleges and institutions sourcing lab consumables in India often keep a bottle at every practical bench.

Supplier

Jain Scientific Equipments Private Limited, which trades as ScienceLab, supplies Universal Disinfectant Spray to schools, colleges, laboratories and healthcare buyers with its wider hygiene and lab equipment range. Vendor registration details for purchase departments: GSTIN 06AAECJ8618A1ZT and Legal Entity Identifier (LEI) 3358004HRD1JIVXKYX49. Read about the company on our company profile.

Related Water, Sanitation & Hygiene Supplies

Products commonly used with the spray in a surface-cleaning routine:

• Universal Disinfectant Wipes — pre-dosed wipes for spills and quick jobs where spraying is not practical.
• Multipurpose Cloth Cotton 1x1.5m — a cotton cloth for wiping surfaces after spraying.
• Sanitization Spray — another spray option in the hygiene range.
• Classroom Cleaning & Sanitization Kit — a trolley kit that combines surface and hand hygiene products for whole-school cleaning.

Find more in Water, Sanitation & Hygiene Supplies.

Frequently Asked Questions

Does Universal Disinfectant Spray need to be diluted?
No. Universal Disinfectant Spray is a ready-to-use formula, so it is sprayed straight from the 1 litre bottle. This removes the mixing, dilution and dispensing errors that can happen when staff prepare disinfectant from a concentrate.

Which surfaces can the spray be used on?
Universal Disinfectant Spray can be used on rubber, plastic, metal, acrylic glass, PVC and anodised aluminium. For any other material, or delicate equipment, test a small hidden area first or ask us before using it.

How quickly does Universal Disinfectant Spray work?
Universal Disinfectant Spray is a fast-acting formula that is stated to inactivate all enveloped viruses in less than 1 minute. Its specification also lists effectiveness against E. coli, Hepatitis B and C virus, HIV, H1N1, Norovirus and Ebola.

Is the spray harsh on hands and surfaces?
Universal Disinfectant Spray has a neutral pH and is described as safer to handle than stronger cleaning chemicals such as chlorine. Users should still follow the label, avoid contact with eyes and keep the bottle out of reach of young children.

What is the shelf life of Universal Disinfectant Spray?
Shelf life of Universal Disinfectant Spray depends on the chemical, its grade and storage conditions, so no fixed period is quoted here. Ask us for the expiry date of the batch you are quoted, and store bottles closed away from heat.

Who supplies Universal Disinfectant Spray?
Universal Disinfectant Spray is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India, to schools, colleges, laboratories, clinics and distributors in India and international markets. Contact us with the number of 1 litre bottles you need for a quotation.

Request a Quote

Request a price for Universal Disinfectant Spray by sending the quantity and delivery address through our contact page, or add it to the enquiry cart with wipes, cloths or other cleaning supplies.

Last updated: 24 September 2026

Universal Disinfectant Wipes (Product Code: SLE/SAH/36) are pre-dosed disinfectant wipes used to clean and disinfect hard surfaces and deal quickly with spills in healthcare, school and laboratory settings. Each of the 200 large wipes carries the correct amount of a neutral pH formula, so there is nothing to dilute or dispense. They are supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India, as a practical lab consumable for everyday hygiene.

Specifications

What Are Universal Disinfectant Wipes Used For?

Wipes are the fastest response when something is spilled or a surface needs cleaning between users: pull one out, wipe the bench, tray, keyboard cover or door plate, and discard it. Because the dose is already in the wipe, a student helper, a nurse or a lab assistant gets the same result as a trained cleaner, and nothing has to be carried except the pack itself.

Use a fresh wipe for each area rather than spreading dirt from one surface to the next, keep the pack closed so the wipes do not dry out, and put used wipes in a lined bin instead of a sink or drain. Schools that run lab practicals every day find that a pack on each bench makes the end-of-lesson wipe-down quick; this is a simple part of waste disposal and hygiene planning in any lab in India.

Supplier

Universal Disinfectant Wipes are supplied by Jain Scientific Equipments Private Limited under its ScienceLab trading name. Schools, colleges, clinics and distributors can order the wipes alongside disinfectant spray, hand hygiene products and laboratory equipment in one enquiry. Learn more on our company profile.

Related Water, Sanitation & Hygiene Supplies

Products that complement the wipes in a daily cleaning routine:

• Universal Disinfectant Spray — the ready-to-use spray version for larger areas.
• Garbage Bags, 100 liters — bin liners for collecting used wipes.
• Alcohol Hand Sanitizer Gel — for hands, since the wipes are intended for hard surfaces.
• Classroom Cleaning & Sanitization Kit — a trolley kit for cleaning rounds across many rooms.

See all products in Water, Sanitation & Hygiene Supplies.

Frequently Asked Questions

How many wipes come in a pack of Universal Disinfectant Wipes?
Each pack of Universal Disinfectant Wipes contains 200 large wipes. Every wipe holds the correct amount of disinfectant solution, so users do not need to dilute or measure anything before cleaning a surface.

What surfaces are Universal Disinfectant Wipes suitable for?
Universal Disinfectant Wipes can be used on rubber, plastic, metal, acrylic glass, PVC and anodised aluminium surfaces. For painted, wooden or delicate surfaces, test on a small area first or ask us for advice before regular use.

How fast do the wipes work?
Universal Disinfectant Wipes use a fast-acting formula stated to inactivate all enveloped viruses in less than 1 minute. The product specification also lists effectiveness against E. coli, Hepatitis B and C virus, HIV, H1N1, Norovirus and Ebola.

When should I use wipes instead of spray?
Universal Disinfectant Wipes suit spills, small areas and quick cleaning between users, because they need no cloth and no dispensing. The spray version is more convenient when larger surfaces such as full benches or tables have to be disinfected.

What is the shelf life of Universal Disinfectant Wipes?
Shelf life of Universal Disinfectant Wipes depends on the chemical, its grade and storage conditions, so we do not state a fixed period. Ask us for the expiry date of the batch you are quoted and keep the pack sealed between uses.

Who supplies Universal Disinfectant Wipes?
Universal Disinfectant Wipes are supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India, to schools, colleges, laboratories, clinics and distributors in India and international markets. Send your required number of packs through the contact page for a quotation.

Request a Quote

To receive a price for Universal Disinfectant Wipes, share the number of packs and your delivery address through our contact page, or add them to the enquiry cart with other cleaning and lab supplies.

Last updated: 24 September 2026

Air Sterilisation Unit (Product Code: SLE/SAH/37) is a compact, mobile UV-C air steriliser used to treat the air inside enclosed rooms such as classrooms, staff rooms, waiting areas and offices where many people gather. Five UV-C tubes inside the unit treat up to 800 m³ of air per hour, sized for a room of about 80 m³, and it runs from a standard 220-240 V supply on smooth castors. It is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India.

Specifications

What Is a UV-C Air Sterilisation Unit Used For?

UV-C light has long been used to kill bacteria and viruses; this unit applies it to room air inside a closed housing, so the treatment happens within the cabinet while people carry on working nearby. It is designed to stand beside staff, students or patients, or in spots where people crowd together, such as a classroom during lessons, an exam hall, a staff room or a reception queue.

Wheel the unit into position, plug it in and switch it on; there are no settings to get wrong, so little training is needed. Match the number of units to room volume at about 80 m³ each, keep inlets and the outlet clear of curtains and furniture, and log running hours so the UV lamps are replaced every 5000 hours. Do not place it near solvent stores or other potentially explosive atmospheres in a laboratory.

What to Specify When Ordering

• The number of units, based on the volume of each room at about 80 m³ per unit.
• Your mains supply and socket type, as the unit is rated AC 220-240 V, 50/60 Hz with a 3-pin plug.
• Whether you want replacement UV-C tubes quoted for future lamp changes (5 tubes per unit); ask us about availability.

Supplier

The Air Sterilisation Unit is sourced and supplied by Jain Scientific Equipments Private Limited, the company that trades as ScienceLab. Alongside laboratory and hygiene products, the company supplies equipment of this kind to schools, colleges, offices and institutions that want to add air treatment to their hygiene measures. Visit the company profile for more about us.

Related Water, Sanitation & Hygiene Supplies

Air treatment is one part of a wider hygiene routine; these products cover surfaces and hands:

• Universal Disinfectant Spray — for hard surfaces, which the air unit does not treat.
• Desk Pad — antiviral covering for desks in the same room.
• Hand Wash Station — a portable wash point for rooms without a sink.
• Alcohol Hand Sanitizer, 150ml — hand sanitiser spray for occupants of the room.

Browse all Water, Sanitation & Hygiene Supplies.

Frequently Asked Questions

How large a room can one Air Sterilisation Unit treat?
One Air Sterilisation Unit is rated for an applicable room size of 80 m³ and treats up to 800 m³ of air per hour. For larger rooms or halls, several units can be combined and spaced around the area.

How does the Air Sterilisation Unit work?
The Air Sterilisation Unit draws room air in through side inlets, exposes it to UV-C radiation from five internal tubes, and an internal fan then returns the treated air to the room through the front outlet.

How often do the UV lamps need replacing?
The UV lamps in the Air Sterilisation Unit need replacing every 5000 hours of operation. Keep a simple log of running hours and contact us in advance if you would like replacement tubes included in a quotation.

How noisy is the Air Sterilisation Unit, and does it produce ozone?
The Air Sterilisation Unit has a sound level of 55 dB or less, and its technical data gives an ozone (O3) concentration of 0.1 mg/m³ or less in the air during dynamic sterilisation.

What power supply does it need?
The Air Sterilisation Unit runs on AC 220-240 V, 50/60 Hz through a standard 3-pin plug, with power consumption of 250 W or less. A single on/off switch controls it, so there is little risk of incorrect operation.

Where should the unit not be used?
Caution is needed when running the Air Sterilisation Unit in a potentially explosive atmosphere, so keep it away from flammable solvent stores. It is designed for working temperatures of -10°C to 40°C and humidity up to 80%.

Who supplies the Air Sterilisation Unit?
The Air Sterilisation Unit is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India, to schools, colleges, offices, institutions and distributors in India and international markets. Share your room sizes through the contact page for a quotation.

Request a Quote

Send the number of units, room sizes and delivery location for the Air Sterilisation Unit through our contact page, or add it to the enquiry cart, and we will prepare a quotation.

Last updated: 24 September 2026

Aluminium Mop Handle with Polypropylene Grip (Product Code: SLE/HE/15) is a threaded, anodised aluminium handle used to carry a mop or other cleaning head for floor cleaning in wards, laboratories, corridors and washrooms. Housekeeping teams choose it for its 1365 mm length and light 0.36 kg weight, finished with a coloured polypropylene grip. It is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India, a lab consumables supplier in India that also sources hygiene items for hospitals and schools.

Specifications

What Is the Aluminium Mop Handle Used For?

The handle is the reach part of a mopping set: the cleaning head screws onto the threaded end, and the operator works the floor standing upright instead of bending. Its 1365 mm length suits most adult users, and at 0.36 kg it adds little weight to a wet mop, which matters on long shifts in wards, corridors and teaching labs where floors are cleaned several times a day.

Anodising gives aluminium a harder, more corrosion-resistant surface than bare metal, so the shaft copes with repeated contact with water and cleaning solutions. Many hospitals use colour-coded grips to keep tools for toilets, wards and kitchens apart; if you follow such a scheme, ask which grip colour will be supplied before ordering. Rinse and dry the handle after use and store it hanging rather than standing on its head.

What to Specify When Ordering

• The number of handles needed per ward, floor or building
• The grip colour, if your site uses colour-coded cleaning tools
• The heads you plan to fit, so thread compatibility can be confirmed
• Whether buckets and mop heads should be quoted with the handles

Supplier

Jain Scientific Equipments Private Limited trades under the ScienceLab name from Ambala, Haryana. Besides laboratory apparatus, the company supplies everyday housekeeping items such as this handle to hospitals, colleges and hostels, so a facility can add cleaning equipment to a larger order instead of buying it separately. More about the business is on the ScienceLab profile page.

Related Water, Sanitation & Hygiene Supplies

The handle is one part of a floor-cleaning set. These items from the same hygiene supplies range complete it:

• Ultra Absorbent Strip Mop — a lint-free mop head for wet cleaning
• Mop Bucket with Strainer — holds the cleaning solution and wrings out the mop
• Gloves, Heavy-duty, Rubber/Nitrile, Large — hand protection when handling cleaning chemicals
• Sprayer Trigger Bottle Handheld 1 Liter — for spot-treating surfaces before mopping

The handle is listed in the Water, Sanitation & Hygiene Supplies range, alongside other cleaning and sanitation items.

Frequently Asked Questions

How long is the Aluminium Mop Handle with Polypropylene Grip?
The Aluminium Mop Handle with Polypropylene Grip is 1365 mm long with a 29 mm x 29 mm section and weighs 0.36 kg. The length lets most adults mop standing upright, while the low weight reduces arm fatigue during long cleaning rounds.

What is the handle made of?
The Aluminium Mop Handle with Polypropylene Grip has an anodised aluminium shaft and a coloured polypropylene grip. Anodised aluminium resists corrosion from water and cleaning solutions, and the plastic grip gives a firmer hold than bare metal when hands are wet.

Will the handle fit my existing mop heads?
The Aluminium Mop Handle with Polypropylene Grip has a threaded end and is intended for the hygiene-range products it is listed with. Thread types vary between brands, so tell us which heads you use and we will confirm compatibility before you order.

How should the mop handle be cleaned and stored?
Wipe the Aluminium Mop Handle with Polypropylene Grip with your usual detergent or disinfectant after each cleaning round, paying attention to the grip, then let it dry. Store it hanging, with any head removed, so moisture does not collect at the threaded end.

Who supplies the Aluminium Mop Handle with Polypropylene Grip?
Jain Scientific Equipments Pvt Ltd (ScienceLab) of Ambala, Haryana, India supplies the Aluminium Mop Handle with Polypropylene Grip. It can be quoted with matching buckets and mop heads so a hospital or school receives a complete cleaning set.

Can the handles be ordered in bulk for several sites?
Yes. The Aluminium Mop Handle with Polypropylene Grip can be quoted in bulk for hospitals, school groups and hostels in India or international markets. Give the quantity, preferred grip colour and delivery address so the quotation reflects your full requirement.

Request a Quote

Send the handle quantity and any matching items through the contact page, or add the Aluminium Mop Handle with Polypropylene Grip to the enquiry cart and submit it with the rest of your housekeeping list.

Last updated: 24 September 2026

Facial Tissues, 2 Ply (Product Code: SLE/SAH/38) are soft, two-layer paper tissues used for wiping the face and nose and for everyday personal hygiene in schools, hotels, offices and sick rooms. Each white sheet measures 200 mm x 200 mm, and the 100 sheets come in an easy-to-dispense box with styled packaging for desks and reception counters. They are supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India.

Specifications

What Are 2-Ply Facial Tissues Used For?

A box of tissues on the teacher's desk, in the school sick room or at a hotel reception lets people cover a cough or sneeze, wipe a runny nose or dab their face without reaching for a shared towel. The two-ply construction gives a sheet that is soft on the skin yet strong enough not to tear when wet, and the dispensing box hands out one tissue at a time so the rest stay clean.

Good tissue etiquette is simple: use a tissue once, drop it straight into a lined bin, and then wash or sanitise hands. Facial tissues are not meant for cleaning optics or wiping chemical spills, so labs should keep them for personal use only. Institutions that order general supplies from a school lab equipment supplier in India often add tissue boxes to classrooms and staff rooms in the same order.

Supplier

These facial tissues are supplied by Jain Scientific Equipments Private Limited, operating as ScienceLab, as part of its range of hygiene consumables for schools, hotels, offices and institutions. Buyers can combine everyday hygiene items with laboratory equipment in one enquiry. Find out more on our company profile.

Related Water, Sanitation & Hygiene Supplies

Products that support personal hygiene alongside facial tissues:

• Garbage Bags, 100 liters — bin liners for disposing of used tissues hygienically.
• Alcohol Hand Sanitizer, 150ml — for cleaning hands after using a tissue.
• Hand Wash Station — a portable sink for washing hands where no plumbing exists.
• Lens Tissue — the correct tissue for cleaning microscope and optical lenses, which facial tissue is not meant for.

See the full Water, Sanitation & Hygiene Supplies range.

Frequently Asked Questions

What size are the Facial Tissues, 2 Ply?
Each sheet of the Facial Tissues, 2 Ply measures 200 mm x 200 mm and is white. The tissues are two layers thick, which makes them soft and gentle on the face while staying strong and absorbent in use.

How many tissues are in each box?
The Facial Tissues, 2 Ply are listed with a quantity of 100 sheets, presented in an easy-to-dispense box. For bulk orders, tell us how many boxes you need and we will confirm the packing arrangement in our quotation.

Where are these facial tissues typically used?
The Facial Tissues, 2 Ply are well suited to schools and hotels, as well as offices, reception desks, staff rooms and sick bays, anywhere people need soft, strong tissues within easy reach.

Can facial tissues be used to clean microscope lenses?
No. The Facial Tissues, 2 Ply are designed for personal use on the face and hands. Optical surfaces such as microscope lenses should be cleaned with purpose-made lens tissue to avoid scratches and lint.

Who supplies the Facial Tissues, 2 Ply?
The Facial Tissues, 2 Ply are supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India, to schools, hotels, offices, institutions and distributors in India and international markets, often together with other hygiene products.

Request a Quote

To order the Facial Tissues, 2 Ply, send the number of boxes and your delivery address through our contact page, or add them to the enquiry cart with other supplies for your school or office.

Last updated: 24 September 2026