Retort Clamp with Bosshead, Rubber Jaws (Product Code: SLE/LC/15) is a rubber-lined diecast alloy clamp used to grip smooth glassware, plastic bottles and tubing firmly on a laboratory retort stand. Its bosshead takes rods up to 15 mm in diameter, and the rubber lining adds friction so smooth, slippery items stay put during room-temperature work. It is produced by Jain Scientific Equipments Pvt Ltd (ScienceLab), an OEM manufacturer, at its own factory in Ambala, India.

Specifications

What Is the Rubber-Jaw Retort Clamp with Bosshead Used For?

Rubber linings give a firm, non-slip hold on smooth and slightly wet surfaces, which makes this clamp a good fit for separating funnels, measuring cylinders, gas jars during collection over water, and plastic bottles or tubing that a hard jaw might dent. The bosshead lets the whole unit be set at any height on a rod of up to 15 mm diameter.

Rubber softens with heat and can swell on contact with some organic solvents and oils, so this version is suited to room-temperature work; for warm glassware the cork-jaw version is the usual choice. Inspect the linings from time to time and clean them with water and a mild detergent rather than solvent. Tighten the bosshead first, then the jaws, so the vessel is never left hanging on a loose clamp.

What to Specify When Ordering

• Quantity — the number of clamps per stand or bench.
• Rod diameter — confirm your stand rods are no thicker than 15 mm.
• Jaw lining — rubber for grip at room temperature, or cork for warm apparatus; many labs order some of each.

OEM Manufacturer

The rubber-jaw clamp is an OEM product of ScienceLab, the trading name of Jain Scientific Equipments Private Limited, and is manufactured at the company's own licensed factory at Saha, Ambala, Haryana, India. Educational institutions, research labs, stockists and importers in India and international markets receive it straight from that factory rather than through a trader. If you need spare parts or a repeat batch to match earlier supplies, the manufacturer handles it directly, so ask us. Background on the company is available on the ScienceLab profile.

Related Retort Clamps and Stand Items

Items that pair with the rubber-jaw clamp in wet-chemistry and gas-collection setups:

• Retort Clamp with Bosshead, Cork Jaws — the cork-lined version for warm apparatus.
• Retort Clamp, Rubber Jaws — a rubber-jaw clamp on its own rod, for use with a separate boss.
• Elastic Clamps for Rubber Pipes (Mohr Clamp) — for pinching rubber tubing in the same setup.
• A-Shape Retort Stand Base — a base for the support rod.
• Burette Stand with Clamp & Bosshead — a ready stand for titrations.

Every clamp style is listed in the Retort Clamp category.

Frequently Asked Questions

What rod diameter does the rubber-jaw clamp's bosshead accept?
The bosshead of the Retort Clamp with Bosshead, Rubber Jaws (SLE/LC/15) accommodates rods up to 15 mm in diameter, so it can be fixed at any height on a retort stand rod within that size.

When should I choose rubber jaws over cork jaws?
Choose the Retort Clamp with Bosshead, Rubber Jaws when you need a firm, non-slip grip on smooth or damp glassware, plastic bottles or tubing at room temperature; choose the cork-jaw version when the apparatus will be warm.

Can the rubber-jaw clamp be used near heat or solvents?
The rubber lining of the Retort Clamp with Bosshead, Rubber Jaws should be kept away from burner flames and hot surfaces, and out of prolonged contact with organic solvents or oils, which can swell or soften rubber.

Who manufactures the Retort Clamp with Bosshead, Rubber Jaws?
The Retort Clamp with Bosshead, Rubber Jaws is manufactured by Jain Scientific Equipments Pvt Ltd (ScienceLab), the OEM, at its own licensed factory at Saha, Ambala, Haryana, India, with quotations issued directly by the manufacturer.

What is the body of the rubber-jaw clamp made of?
The Retort Clamp with Bosshead, Rubber Jaws has a diecast alloy body with rubber-lined jaws and comes complete with a bosshead, giving a compact clamp that mounts straight onto a laboratory stand rod.

Is the rubber-jaw clamp available for bulk or export orders?
Yes, ScienceLab supplies the Retort Clamp with Bosshead, Rubber Jaws in laboratory, institutional and dealer quantities for India and international markets. Share the quantity and destination through the contact page for a manufacturer's quotation.

Request a Quote

To price the Retort Clamp with Bosshead, Rubber Jaws, send your quantity via the contact page or add it to the enquiry cart. As the manufacturer, ScienceLab prepares the quotation itself, including any matching stands you list.

Last updated: 24 September 2026

Retort Clamp, Cork Jaws (Product Code: SLE/LC/17) is a four-prong laboratory clamp with cork-lined jaws, used to hold items from 2 to 90 mm in diameter, from thin tubes to flasks, on a retort stand. It has a blue coated finish, an overall length of 245 mm and a 145 mm rod, and its jaw design keeps a firm grip at every angle of opening. It is made by Jain Scientific Equipments Pvt Ltd (ScienceLab), an OEM manufacturer, at its own factory in Ambala, India.

Specifications

What Is the Four-Prong Cork-Jaw Retort Clamp Used For?

The wide 2–90 mm range means one clamp can hold a thin tube for one experiment and a mid-sized round-bottom flask for the next, cutting down the number of clamp types a lab has to stock. Four cork-lined prongs close evenly around the item, and because the jaw geometry keeps its grip at all angles of opening, small items are held as firmly as larger ones.

Cork cushions glass and insulates against moderate warmth, and on this clamp the liners are well secured to the jaws, so they stay put through repeated tightening. The 145 mm rod fits into a boss or clamp holder on a retort stand, while the blue coating protects the metal and makes the clamp easy to pick out on a shared bench. Keep the cork away from open flame and wipe it with a dry cloth after use.

What to Specify When Ordering

• Quantity — the number of clamps needed per stand or bench.
• Mounting — the clamp fixes by its 145 mm rod, so each one needs a boss or clamp holder on the stand.
• Largest item — check that your widest vessel is within the 90 mm capacity; for wider items see other clamps in the category.

OEM Manufacturer

ScienceLab, the trading name of Jain Scientific Equipments Private Limited, is the OEM of the Retort Clamp, Cork Jaws and makes it at its own licensed factory at Saha, Ambala, Haryana, India. Schools, college chemistry departments, industrial QC labs, dealers and importers in India and international markets are supplied factory-direct, with quotations prepared by the manufacturer. For extra clamps to match an earlier order, or for spare-part questions, ask us. The ScienceLab company profile has more about the business.

Related Retort Clamps and Holders

Holders, bases and alternative clamps that work with the four-prong cork-jaw clamp:

• Adjustable Clamp Holder — fixes the clamp rod to the stand.
• A-Shape Retort Stand Base — a base for the vertical support rod.
• Retort Clamp with Bosshead, Cork Jaws — cork jaws with a bosshead included.
• Retort Clamp, Rubber Jaws — the rubber-lined alternative for smooth or damp items.
• Retort Clamp Four Finger — another four-finger design from the chemistry range.

Compare every clamp in the Retort Clamp category.

Frequently Asked Questions

What size of items does the Retort Clamp, Cork Jaws hold?
The Retort Clamp, Cork Jaws (SLE/LC/17) accepts articles from 2 to 90 mm in diameter, so it can hold narrow tubes as well as flasks and bottles of moderate size, with a firm grip at all angles of opening.

What are the dimensions of the Retort Clamp, Cork Jaws?
The Retort Clamp, Cork Jaws has an overall length of 245 mm and a rod length of 145 mm. The rod is fixed into a boss or clamp holder on a retort stand to position the four cork-lined prongs.

Does the Retort Clamp, Cork Jaws include a bosshead?
The Retort Clamp, Cork Jaws is a clamp on a 145 mm rod and is not listed with a bosshead. Use a separate boss or adjustable clamp holder, or choose the Retort Clamp with Bosshead, Cork Jaws if you want both together.

Who manufactures the Retort Clamp, Cork Jaws?
Jain Scientific Equipments Pvt Ltd (ScienceLab) manufactures the Retort Clamp, Cork Jaws as the OEM at its own licensed factory at Saha, Ambala, Haryana, India, and sells it factory-direct to laboratories, schools, dealers and importers.

How should I look after the cork jaws?
Wipe the cork jaws of the Retort Clamp, Cork Jaws with a dry cloth after use, avoid soaking them in water or solvents, and keep them away from open flame. The liners are well secured to the jaws, so they stay in place during normal tightening.

What details should I send for a Retort Clamp, Cork Jaws quote?
For a Retort Clamp, Cork Jaws quote, send the quantity, whether you also need bosses, clamp holders or stand bases, and the delivery location in India or abroad through the contact page. The manufacturer replies with a direct quotation.

Request a Quote

Get a quotation for the Retort Clamp, Cork Jaws by writing through the contact page or adding it to the enquiry cart with any stand parts. ScienceLab quotes as the manufacturer, whether you need a few clamps or a full lab fit-out.

Last updated: 24 September 2026

Retort Clamp, Rubber Jaws (Product Code: SLE/LC/18) is a laboratory clamp with rubber-lined diecast jaws, used to hold flasks, bottles and tubes up to 90 mm across on a retort stand. It is mounted on a 135 mm rod of 8 mm diameter, measures 250 mm overall, and its clamping rod works through swivels set into the jaws so they settle evenly on the item. It is manufactured by Jain Scientific Equipments Pvt Ltd (ScienceLab), an OEM, at its own factory in Ambala, India.

Specifications

What Is the Rubber Jaw Retort Clamp Used For?

A 90 mm jaw capacity covers a wide range of everyday glassware on a student bench, including conical flasks, reagent bottles, measuring cylinders and boiling tubes. The swivels in the jaws let each jaw pivot slightly as the clamping rod is tightened, so the rubber pads sit flat against curved or tapered surfaces instead of pinching at one point.

Before setting up, check that your boss or clamp holder grips an 8 mm rod securely; the 135 mm rod length decides how far the vessel sits from the stand upright. The rubber lining grips smooth glass well but should be kept away from flames, hot plates and prolonged solvent contact. Used this way, it is a common piece of chemistry lab equipment on school and college benches.

OEM Manufacturer

Jain Scientific Equipments Private Limited, whose brand is ScienceLab, is the OEM of the Retort Clamp, Rubber Jaws and produces it at its own licensed factory at Saha, Ambala, Haryana, India. That factory ships directly to teaching labs, research institutes, lab-supply dealers and importers in India and international markets, so pricing, repeat orders and spares are all handled by the maker. Ask us if you need clamps to match ones supplied earlier. Company details are on the ScienceLab profile.

Related Retort Clamps and Holders

These items fit alongside the rubber jaw clamp on the same stand:

• Adjustable Clamp Holder — to fix the clamp rod to a stand.
• Retort Clamp with Bosshead, Rubber Jaws — rubber jaws with a bosshead included.
• Retort Clamp, Cork Jaws — a four-prong cork-lined clamp for warmer work.
• Universal Clamp — for awkwardly shaped apparatus.
• Elastic Clamps for Rubber Pipes (Mohr Clamp) — to control tubing connected to the clamped vessel.

Browse the full Retort Clamp category for other jaw linings and sizes.

Frequently Asked Questions

What is the jaw capacity of the Retort Clamp, Rubber Jaws?
The Retort Clamp, Rubber Jaws (SLE/LC/18) has a jaw capacity of 90 mm, so it can hold items up to that diameter, from test tubes and boiling tubes to conical flasks and reagent bottles.

How is the Retort Clamp, Rubber Jaws mounted on a stand?
The Retort Clamp, Rubber Jaws is mounted on a 135 mm rod of 8 mm diameter. Fix that rod in a boss or clamp holder on your retort stand, making sure the fitting grips an 8 mm rod securely before loading the clamp.

What do the swivels in the jaws of this clamp do?
In the Retort Clamp, Rubber Jaws, the clamping rod operates through swivels mounted in the jaws, which lets the rubber-lined jaws settle evenly against the item as they close instead of pressing at a single point.

Who manufactures the Retort Clamp, Rubber Jaws?
The Retort Clamp, Rubber Jaws is manufactured by Jain Scientific Equipments Pvt Ltd (ScienceLab), the OEM, at its own licensed factory at Saha, Ambala, Haryana, India. Laboratories, dealers and importers buy it direct from the manufacturer.

What is the overall length of the Retort Clamp, Rubber Jaws?
The Retort Clamp, Rubber Jaws is 250 mm long overall and sits on a 135 mm mounting rod. Allow for this reach when planning how far the vessel will sit from the stand upright and from neighbouring equipment.

How do I get a quotation for the Retort Clamp, Rubber Jaws?
To get a quotation for the Retort Clamp, Rubber Jaws, send the quantity, any clamp holders or stands required and your delivery location through the contact page. ScienceLab, as the manufacturer, replies with a direct quote for India or international delivery.

Request a Quote

Enquire about the Retort Clamp, Rubber Jaws via the contact page, or add it to the enquiry cart together with holders and stands. Quotes come directly from ScienceLab, the manufacturer, for laboratories, institutions and resellers.

Last updated: 24 September 2026

Retort Metalware Kit (Product Code: SLE/LR/19) is a class set of retort stand metalware used to equip student work stations for basic chemistry experiments in schools and colleges. It contains five heavy-duty 200 × 125 mm retort bases, five 600 mm steel retort rods, five die cast retort clamps and five PVC coated retort clamps, so the set divides evenly into five stations, each with a base, a rod and two clamps. It is made by Jain Scientific Equipments Pvt Ltd (ScienceLab), an OEM manufacturer, at its own factory in Ambala, India, as a ready chemistry teaching kit for Indian schools.

Specifications

What Is the Retort Metalware Kit Used For?

Most first chemistry practicals need something held above the bench: a funnel over a beaker for filtration, a boiling tube over a burner, a delivery tube feeding a gas jar, or a condenser in a simple distillation. This kit gives a teacher enough bases, rods and clamps to run the same experiment at five stations at once, instead of sharing one stand around the room.

The two clamp types have different jobs. The die cast clamps give a firm, rigid grip for heavier items, while the PVC coated clamps cushion glass so test tubes and flasks are less likely to slip or crack. Set the bases on a flat bench, keep loads above the base, and count the pieces back in after class so every station stays complete.

What to Specify When Ordering

• The number of kits (each kit covers five stations).
• Any extra clamps, bossheads or retort rings needed for particular experiments.
• The delivery location, in India or abroad.

OEM Manufacturer

The Retort Metalware Kit is assembled by Jain Scientific Equipments Private Limited, trading as ScienceLab, which is the OEM (original equipment manufacturer) and makes it at its own licensed factory at Saha, Ambala, Haryana, India. The company is registered as an MSME manufacturer under Udyam number UDYAM-HR-01-0003714, and ships kits abroad under Importer-Exporter Code AAECJ8618A issued by the DGFT.

If a piece goes missing or is damaged, ask us about a replacement for that part. More information is on the ScienceLab profile.

Related Stand Bases, Rods and Rings

Add-ons that extend what the kit can do:

• Retort Rings — hold a funnel or a gauze on the rod.
• Retort Clamp 3 Prongs — an extra clamp for round flasks and condensers.
• Bosshead — for fixing additional clamps or rings to a rod.
• Gauze Wire — spreads the flame under glassware heated on a ring.

Browse the Stand Bases, Rods and Rings category and the Retort Clamp category.

Frequently Asked Questions

What is included in the Retort Metalware Kit?
The Retort Metalware Kit includes five heavy-duty retort bases of 200 × 125 mm, five steel retort rods 600 mm long, five die cast retort clamps and five PVC coated retort clamps, twenty pieces in all.

How many students can use one Retort Metalware Kit?
One Retort Metalware Kit equips five work stations, each with a base, a rod and two clamps. Larger classes simply order more kits, or add loose clamps and rods from our range.

Why does the kit contain two types of clamp?
The Retort Metalware Kit mixes die cast clamps, which grip heavier apparatus firmly, with PVC coated clamps, which cushion glassware such as test tubes and small flasks, so each station can hold both kinds of item.

Can extra parts be ordered with the Retort Metalware Kit?
Yes. Extra clamps, bossheads, retort rings or replacement rods and bases can be quoted alongside the Retort Metalware Kit. List what you need on the contact page.

Who manufactures the Retort Metalware Kit?
The Retort Metalware Kit is manufactured by Jain Scientific Equipments Pvt Ltd (ScienceLab), the OEM, at its own licensed factory at Saha, Ambala, Haryana, India, and is sold factory-direct to schools, colleges and dealers.

Is the Retort Metalware Kit available for bulk school orders or export?
Yes. The Retort Metalware Kit is supplied in bulk to schools and dealers in India and international markets. Give the number of kits and the delivery destination for a quotation.

Request a Quote

To buy class sets, contact us through the contact page or add the kit to the enquiry cart. Quotes come direct from the manufacturer.

Last updated: 24 September 2026

Rubber Tubing (Product Code: SLE/LI/37) is a heavy-duty, high-pressure red rubber tube used to make flexible connections between taps, pumps, glassware and apparatus in laboratory set-ups. It has an 8 mm bore with a thick 4.5 mm wall and comes as a 10 m roll, so each lab can cut lengths to suit its benches. It is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India, a lab consumables supplier in India for schools, colleges and dealers.

Specifications

What Is Rubber Tubing Used For?

In teaching and routine laboratories, rubber tubing carries water or air between fixed fittings and apparatus: linking a condenser to the water tap and drain, joining a water filter pump to a filter flask, or running a delivery line from a gas-generation flask to a collecting vessel. The 4.5 mm wall resists kinking where a line bends around the bench, and a roll kept in the preparation room covers most connections a school lab setup in India needs during practical sessions.

Cut lengths square with a sharp blade, and ease the tube onto glass nozzles wetted with a little water rather than forcing it, so the glass does not snap. Fit a screw clip where flow must be regulated or shut off. For gas taps and Bunsen burners, use tubing intended for gas connections, such as our burner tubing listed below.

What to Specify When Ordering

• The number of 10 m rolls needed for your laboratories
• That the 8 mm bore suits the outside diameter of your nozzles and glass tubes
• Whether you also need screw clips, a filter pump or filter flasks on the same order
• Delivery location, and whether the order is for one institution, a dealer or export

Supplier

Jain Scientific Equipments Private Limited trades under the ScienceLab name and supplies this red rubber tubing from Ambala, Haryana, alongside the glassware and apparatus it connects. Laboratories can add rolls to a wider equipment order so that tubing, clips and flasks arrive together. Company background is on our ScienceLab company profile.

Related Laboratory Instruments

These items are used with rubber tubing in water, suction and gas-delivery set-ups:

• Hoffman Screw Clip — squeezes the tubing to regulate or stop flow.
• Filter Pump, Borosilicate Glass — tap-mounted pump that the tubing links to a filter flask.
• Conical Filter Flask — side-arm flask that receives the suction line.
• Vacuum Tubing — purpose-made alternative for dedicated vacuum lines.
• Bunsen Burner Tubing — for connecting burners to the gas tap.

Browse the full Laboratory Instruments range for more bench equipment.

Frequently Asked Questions

What size is this rubber tubing?
The ScienceLab Rubber Tubing (SLE/LI/37) has an 8 mm bore and a 4.5 mm wall thickness. It is made of red rubber and described as heavy-duty, high-pressure tubing, so it suits firm connections on glass nozzles and taps of matching size.

How much tubing is in one order unit?
Rubber Tubing SLE/LI/37 is supplied in a 10 m roll. Laboratories cut it into short lengths for condensers, filter pumps and delivery tubes, so order several rolls when equipping more than one lab or stocking a central store.

Can this rubber tubing be used for vacuum filtration?
Heavy-walled Rubber Tubing such as SLE/LI/37 is often used between a water filter pump and a filter flask, but its listing gives no vacuum rating. For dedicated vacuum lines, compare our Vacuum Tubing, or ask us which tubing suits your pump.

Is this tubing suitable for gas burners?
For Bunsen burners and gas taps, choose tubing supplied for gas connections, such as our Bunsen Burner Tubing. The red Rubber Tubing SLE/LI/37 is intended for general laboratory connections; tell us your application and we will confirm the right tubing.

How should rubber tubing be stored and looked after?
Store Rubber Tubing away from direct sunlight, heat, oils and solvents, all of which age rubber. Before each practical, flex the ends and replace any length that is cracked, hardened or sticky, cutting a fresh square end instead of reusing a split one.

Who supplies Rubber Tubing SLE/LI/37?
Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, Haryana, India supplies this Rubber Tubing to schools, colleges, laboratories and dealers. It can be combined with glassware and apparatus in one quotation for institutional, bulk and export orders.

What does a quotation for this tubing need?
To quote Rubber Tubing SLE/LI/37, send the number of 10 m rolls, any clips or glassware to add, and the delivery location through our contact page. Bulk and export supply to India and international markets is quoted on request.

Request a Quote

Send your requirement through our contact page or add Rubber Tubing to the enquiry cart with the number of rolls you need. We reply with a quotation for supply within India and to international markets.

Last updated: 24 September 2026

Safety Goggles (Product Code: SLE/LI/38) are polycarbonate protective eyewear worn to help protect the eyes during practical work in school, college and general laboratories. An adjustable strap lets one design fit different wearers across a class, and the goggles are meant for laboratory use, not for medical use. They are supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India, for institutions buying safety goggles for school labs in India.

Key Details

What Are Safety Goggles Used For?

Goggles belong on every face whenever a practical involves heating liquids, pouring acids or alkalis, crushing solids or working near glassware that could crack. Because they enclose the eye area more fully than ordinary spectacles, many schools make them compulsory for chemistry sessions, and they are among the first items on any list of school chemistry lab equipment in India.

Adjust the strap so the goggles sit snugly before the practical starts, put them on before any reagent bottle is opened, and keep them on until the whole bench has finished and cleared up. After class, wash them in mild soapy water, dry them with a soft cloth and store them in a closed box so the polycarbonate does not pick up scratches.

Supplier

ScienceLab is the trading name of Jain Scientific Equipments Private Limited, which supplies these polycarbonate goggles from Ambala, Haryana, together with other lab safety items and apparatus. Schools setting up or restocking a laboratory can order goggles in class quantities with the rest of their equipment list. Learn more on our company profile.

Related Laboratory Instruments

Other protective items that are worn or set up alongside safety goggles:

• Premium Safety Spectacles — spectacle-style alternative eyewear for the lab.
• Safety Screen — clear bench shield placed in front of demonstrations.
• Lab Coat — body protection worn together with goggles.
• Transparent Plastic Laboratory Apron — splash protection for practical work.
• Eye Wash Station — emergency eye-rinsing point for the laboratory.

See the complete Laboratory Instruments category for more equipment.

Frequently Asked Questions

What are these safety goggles made of?
The ScienceLab Safety Goggles (SLE/LI/38) are made of polycarbonate and fitted with an adjustable strap. Polycarbonate is a tough, clear plastic commonly chosen for laboratory eyewear because it stays light to wear through a full practical session.

Can one size fit a whole class?
Safety Goggles SLE/LI/38 have an adjustable strap, so the same goggles can be tightened or loosened for different head sizes in a class. For very young children or special fitting needs, contact us before ordering class sets.

Are these safety goggles suitable for medical use?
No. The Safety Goggles SLE/LI/38 are laboratory eye protection and are not for medical use. They are intended for school, college and general laboratory practicals; buyers who need clinical protective equipment should discuss their requirement with us.

How should the goggles be cleaned?
Clean the Safety Goggles with mild soap and lukewarm water, rinse, and let them air-dry or wipe them with a soft cloth. Avoid solvents and abrasive pads, which can cloud polycarbonate, and keep the goggles in a closed box between classes.

Do the goggles fit over prescription glasses?
The listing for Safety Goggles SLE/LI/38 does not state whether they fit over prescription spectacles. If some students or staff wear glasses, mention it when you enquire and we will advise on suitable eyewear from our range.

Who supplies Safety Goggles SLE/LI/38?
Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, Haryana, India supplies these Safety Goggles to schools, colleges, laboratories and dealers, and can include them in larger lab equipment orders delivered across India and to international markets.

What information is needed for a quotation?
For a Safety Goggles quotation, send the number of pairs, any other safety items or apparatus you need, and the delivery address. Class-set, bulk and export enquiries are handled through our contact page.

Request a Quote

Ask for prices on Safety Goggles through our contact page, or place them in the enquiry cart with your other laboratory items so everything is quoted together.

Last updated: 24 September 2026

Safety Screen (Product Code: SLE/LI/39) is a transparent polycarbonate shield used to put a clear barrier between a demonstration and the people watching it in school and college laboratories. A 300 mm central panel is hinged to two 225 mm side panels, all 4 mm thick and 610 mm high, so the screen can be angled around the apparatus. It is made by Jain Scientific Equipments Pvt Ltd (ScienceLab), an OEM manufacturer, at its own factory in Ambala, India, as part of its school chemistry lab equipment.

Specifications

What Is a Safety Screen Used For?

A bench safety screen stands in front of demonstrations that might spit, splash or crack glassware — reactive metals in water, vigorous exothermic reactions, or apparatus being heated or run under reduced pressure. The clear polycarbonate lets a whole class follow each stage while the panels sit between the apparatus and the audience.

Face the central panel towards the observers and fold the hinged side panels back to close off the sides. The screen adds to goggles and a fume cupboard; it never replaces them. For cleaning, use mild soap and water only, because solvents such as acetone can craze polycarbonate. It is a sensible addition to chemistry lab equipment for schools in India where teachers demonstrate reactions to full classes.

OEM Manufacturer

The Safety Screen is produced by Jain Scientific Equipments Private Limited, which trades as ScienceLab and is the original equipment manufacturer (OEM) of this item. It is made at the company's own licensed factory at Saha, Ambala, Haryana, India, rather than bought in from a trader, and is supplied factory-direct to schools, colleges, institutions, dealers and importers.

Because the maker handles enquiries itself, questions about replacement panels or repeat orders for more demonstration benches go straight to the manufacturer — just ask us. Read more on our company profile.

Related Laboratory Instruments

Equipment used with a safety screen during demonstrations:

• Safety Goggles — eye protection still worn behind the screen.
• Premium Safety Spectacles — alternative eyewear for observers.
• Fume Cupboard, Ductless — for demonstrations that give off fumes.
• Retort Stand — holds apparatus steady behind the screen.
• Transparent Plastic Laboratory Apron — splash protection for the demonstrator.

More items are listed under Laboratory Instruments.

Frequently Asked Questions

What are the dimensions of the Safety Screen?
The ScienceLab Safety Screen (SLE/LI/39) has three sections 225 mm, 300 mm and 225 mm wide, made from 4 mm thick polycarbonate, with an overall height of 610 mm. The two side panels are hinged to the central panel.

Why is polycarbonate used for the Safety Screen?
The Safety Screen SLE/LI/39 uses transparent polycarbonate so that students can watch a demonstration clearly through the panels. Polycarbonate is a tough plastic widely used for laboratory shields, and the 4 mm panels form a rigid, clear barrier on the bench.

Does a safety screen replace goggles or a fume cupboard?
No. The Safety Screen SLE/LI/39 is an extra barrier between a demonstration and its observers. The demonstrator and students should still wear safety goggles, and any reaction that releases fumes belongs in a fume cupboard.

How do I clean the Safety Screen?
Wipe the Safety Screen with mild soap and water and dry it with a soft cloth. Avoid acetone and other organic solvents or abrasive cleaners, which can craze or scratch polycarbonate and spoil the clear view through the panels.

Who manufactures the Safety Screen SLE/LI/39?
Jain Scientific Equipments Pvt Ltd (ScienceLab) is the OEM manufacturer of the Safety Screen and makes it at its own licensed factory at Saha, Ambala, Haryana, India. Schools, dealers and importers buy it directly from the manufacturer.

Can replacement panels be supplied?
For replacement panels or hinges for the Safety Screen SLE/LI/39, contact us with the product code and the part you need. As the manufacturer, we will confirm what can be supplied and quote it directly.

What should a quotation request include?
For a Safety Screen quotation, send the number of screens, any related safety items such as goggles, and your delivery location. Bulk orders for several schools and export enquiries from international markets are welcome through our contact page.

Request a Quote

Quotations for the Safety Screen come direct from the manufacturer. Write to us via the contact page or add the screen to the enquiry cart, and we will reply with pricing for India or export delivery.

Last updated: 24 September 2026

Sanitization Spray (Product Code: SLE/SAH/25) is a multi-surface disinfectant cleaner spray used to sanitise frequently touched surfaces such as touch screens, keypads and control panels in schools, labs, offices and kitchens. It comes in a handy 150 ml bottle with a lockable trigger, is perfume free and non-tainting, and is described as food-safe, supplied in packs of 12. It is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India.

Specifications

What Is the Sanitization Spray Used For?

Shared devices and controls are handled by many people in a day: lab instrument keypads, smartboard and tablet screens, lift and door buttons, photocopier panels and the fronts of kitchen appliances. This spray is intended for exactly those touch points. Because it is perfume free and non-tainting, it also suits staff rooms, canteens and food-preparation areas where a scented cleaner would be unwelcome.

For screens and electronics, spray onto a clean cloth rather than directly onto the device, then wipe; follow the label for any contact time. The trigger locks for storage and transport, and the 150 ml bottle is small enough for a desk drawer, lab bench or vehicle glovebox. Always read and follow the safety directions printed on the label.

What to Specify When Ordering

• Number of packs: the spray is supplied in packs of 12 bottles of 150 ml.
• Batch expiry: ask for the expiry date of the batch in your quotation.
• Safety information: request the label and safety data you need for your site records.
• Companion items: add hand sanitiser or cleaning kits if you are equipping classrooms or vehicles.

Supplier

ScienceLab, the trading name of Jain Scientific Equipments Private Limited in Ambala, Haryana, supplies this Sanitization Spray as part of its sourced hygiene range for schools, colleges, offices and dealers. For vendor registration, the supplying company can be identified by GSTIN 06AAECJ8618A1ZT and LEI 3358004HRD1JIVXKYX49; these are company trade registrations, not product approvals. See the company profile for more.

Related Water, Sanitation & Hygiene Supplies

Other items used in the same cleaning routine:

• Universal Disinfectant Spray — another disinfectant spray option for comparison.
• Classroom Cleaning & Sanitization Kit — a kit for routine classroom cleaning.
• Driver Sanitization Kit — gloves and sanitising solution for vehicles.
• Hand sanitizer Alcohol >60% 500ml w. Pump — for hands, as the spray is meant for surfaces.

Browse all hygiene products in Water, Sanitation & Hygiene Supplies.

Frequently Asked Questions

What size and pack does the Sanitization Spray come in?
The Sanitization Spray comes in a 150 ml bottle with a lockable trigger, supplied in a pack of 12. Quote requests should state the number of packs needed so pricing can be calculated for the full quantity.

What surfaces is the Sanitization Spray intended for?
The Sanitization Spray is intended for frequently touched surfaces such as control panels, touch screens, keypads, button controls and appliance surfaces. For electronics, spray onto a cloth first and follow the label directions.

What does the Sanitization Spray kill?
The product description states that the Sanitization Spray kills 99.9% of bacteria, including MRSA, E. coli, Listeria and Salmonella. Use it exactly as the label directs, including any contact time, for the stated performance.

Can the Sanitization Spray be used in food areas?
The Sanitization Spray is described as food-safe, perfume free and non-tainting, so it is suited to canteens, staff rooms and food-preparation surfaces. Follow the label for any rinsing instructions on food-contact surfaces.

What is the shelf life of the Sanitization Spray?
The shelf life of the Sanitization Spray depends on the chemical, its grade and storage conditions. Ask us through the contact page for the expiry date of the batch you are quoted.

Who supplies the Sanitization Spray?
Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, Haryana, supplies the Sanitization Spray to schools, institutions, offices and dealers in India and international markets, and can quote it together with other hygiene supplies.

Request a Quote

For pricing on product code SLE/SAH/25, send the number of packs and delivery location through the contact page, or add the spray to the enquiry cart.

Last updated: 24 September 2026