The CRDI Diesel Engine Stand, Motor Type is a sectioned 2,900cc CRDI Delphi diesel engine that a 220V motor runs automatically, the way it turns in a vehicle. An engine speed controller sets the pace, and an LED lamp turns on at ignition. The starting motor, generator, air conditioner compressor and intake manifold stay fitted, and the steel frame rolls on 4 braked wheels.
| Parameter | Detail |
|---|---|
| Engine | 2,900cc CRDI Delphi engine, sectioned by precise cutting |
| Engine equipment | Starting motor, generator, air conditioner compressor, intake manifold |
| Systems | Fuel system, cooling system, lubrication system |
| Operation | Automatic operation type, driven by 220V motor with engine speed controller; LED lamp turns on at ignition |
| Protection | Safety breaker, emergency switch, safety fuse |
| Stand | Steel frame with heat treatment painting; 4 wheels with brakes |
| Finish | Each engine part painted specifically; incised sections in different colours |
| Weight and size | Approx. 150 kg; approx. 700 × 650 × 1,500 mm |
| Training contents | Attaching and detaching the generator and starting motor; replacing the timing belt and the other engine belts; replacing the oil filter |
| Product code | SLE/ATE/16 |
| Minimum order | 10 units |
| Dispatch | Usually within 7 to 10 working days |
| Manufacturer | ScienceLab (Jain Scientific Equipments Pvt Ltd), Ambala, India |
Four-stroke cycle watch. Run the engine slowly on the speed controller and follow one cylinder through suction, compression, power and exhaust. Students call out each stroke as the piston and valves move, and mark where fuel would enter near the top of compression. Newer groups can start on a simpler four-stroke diesel engine model.
Working out the firing order. Students number the cylinders, then watch the cut crank and valves to find the order in which each cylinder reaches its power stroke. They confirm it over a second full cycle and explain how that order spreads the power impulses along the crankshaft.
Service round. With the drive off at the safety breaker and the emergency switch within reach, each group in turn slackens and removes the generator, refits it and re-tensions its belt. The next group renews the oil filter, and a third detaches and refits the starting motor.
Whole engine and injection hardware. Pair the stand with the CRDI pump and nozzle set. Students find where the high-pressure pump, rail and injectors sit on the cut engine, then study a sectioned injector nozzle up close on the bench.
By heat of compression. Only air enters on the suction stroke, and squeezing it on the compression stroke makes it hot enough to light diesel. Fuel is injected near top dead centre and ignites by itself. On this stand, an LED lamp turns on at ignition.
So that power strokes are spread evenly along the crankshaft. Firing neighbouring cylinders one after another would load one end of the crank and its bearings heavily and make the engine run rough. A good firing order balances the forces, smooths running and shares heat across the block.
Ignition delay. Fuel injected in the short gap before combustion starts collects in the cylinder, then burns all at once, giving a sharp pressure rise that is heard as knock. A cold engine or poor fuel lengthens the delay, and common rail systems shorten it with a small pilot injection.
Cold metal draws heat from the compressed air, so it may not get hot enough to light the fuel, and the engine cranks long and coughs. Glow plugs heat the combustion chamber before and during starting. A failed glow plug in one cylinder shows as rough running until the engine warms up.
Yes. A diesel must crank fast enough to build compression heat, and a weak battery turns it too slowly. A generator that is not charging lets the battery run down between starts. Check battery voltage and generator output with a digital multimeter before suspecting the fuel system.
It weighs about 150 kg on a steel frame with 4 wheels, each with a brake. Release the brakes, push it with two people, and lock every wheel again before the motor is started. Its overall size is about 700 × 650 × 1,500 mm.
To request a quotation, send the product name, code and quantity through our contact page or add the item to your enquiry cart.
Last updated: 20 November 2026