The CRDI Diesel Engine Power Train System F/R Type is a sectioned vehicle chassis that shows power flowing from a diesel engine through an F/R type manual transmission, driveshaft and rear axle. Steering, brakes, shock absorbers, lighting and a battery sit on the same frame. An AC 220V motor moves the power train as in an actual car. Its diesel engine and manual transmission are production units; the stand is built in Ambala.
| Parameter | Detail |
|---|---|
| Type | Operating F/R type manual transmission CRDI and power train system structure of a diesel engine vehicle |
| Power train | Diesel engine assembly, manual transmission assembly, change lever, driveshaft, rear axle |
| Engine and transmission | Sourced production units (as listed) |
| Chassis systems | Brake system, steering system, shock absorber |
| Other equipment | 1 set of lighting, fuel tank, battery, intake/exhaust system |
| Drive for demonstration | AC 220V motor operation |
| Finish | Precisely cut to show internal structure; incised sections painted in different colours |
| Weight and size | Approx. 450 kg; approx. 3,000 × 2,000 × 1,300 mm |
| Training contents | Brake lining and pad adjustment and replacement; shock absorber and spring replacement; tyre replacement; fuel pump attaching, detaching and inspection; oil filter replacement; belt replacement and tension control |
| Product code | SLE/ATE/17 |
| Minimum order | 10 units |
| Dispatch | Usually within 7 to 10 working days |
| Manufacturer | ScienceLab (Jain Scientific Equipments Pvt Ltd), Ambala, India |
Gear-by-gear power flow. With the drive stopped, select a gear on the change lever, then run the motor and watch how fast the driveshaft turns. Repeat for each gear and for reverse. Students then find the matching gear pairs inside a five-speed manual gearbox cutaway.
Where the clutch sits. On a manual power train the clutch sits inside the bell housing, between engine and gearbox. Open the lesson out with a Clutch Structure Trainer Mechanical Manual so learners see what happens between the engine and the manual gearbox when the pedal goes down.
Shock absorber and spring replacement. With the motor switched off, a group removes one shock absorber and its spring, using a spring compressor where the spring sits on the damper. They stroke the old damper by hand: a sound one resists smoothly over its whole travel, with no free spots, jerks or oil leaks. Then they refit the parts and tighten every mounting.
Tyre change and oil filter. One group removes and refits a tyre, tightening the wheel nuts in a criss-cross pattern. Another removes the oil filter, wipes the mounting face, lightly oils the seal of the new filter and tightens it by hand.
The gearbox is fixed to the frame while the axle moves up and down on its springs, so the driveshaft angle keeps changing. Universal joints pass the drive through that changing angle. A single Hooke's joint makes the driven shaft speed up and slow down within each turn, so joints are used in phased pairs.
A clunk when a gear is engaged or the drive is taken up, a squeak at low speed, and vibration that appears at certain road speeds. Grip the shaft near each joint and twist it by hand. Any free play or roughness means the joint needs replacing.
It matches the speed of a gear and its shaft before they lock together. A small cone clutch in the synchroniser brings the gear up or down to speed, then the sleeve slides over the dog teeth. Without synchromesh, the driver must double declutch to avoid gear clash.
A diesel engine gives useful torque only over a limited speed band. Low gears multiply that torque for starting off and climbing, and high gears let the engine turn slowly at cruising speed. The gearbox also provides neutral and reverse.
At the service interval the vehicle maker sets, and again after any suspension work. Greaseable joints take fresh grease until clean grease shows at every seal, while sealed joints are only checked for play. Check the driveshaft working angles as well, because a wrong angle wears joints quickly.
No. The power train is listed as a diesel engine assembly with a manual transmission assembly, both production units, without a named model or displacement. A version with an automatic transmission, the CRDI Diesel Engine Power Train System Automatic Transmission, is listed separately.
To request a quotation, send the product name, code and quantity through our contact page or add the item to your enquiry cart.
Last updated: 20 November 2026