Retort Clamp

Retort Clamp Standard 18/10 Stainless Steel (Product Code: SLE/RC/01) is a round-jaw laboratory clamp used to hold flasks, tubes and other round apparatus on a retort stand. It is made from 18/10 stainless steel in seven sizes, from 150 mm long with a 10 mm shaft and 25 mm span up to 180 mm long with a 12 mm shaft and 150 mm span. It is manufactured by Jain Scientific Equipments Pvt Ltd (ScienceLab), an OEM, at its own factory in Ambala, India.

Specifications

What Is the Standard Retort Clamp Used For?

A standard retort clamp grips a flask, condenser, test tube or column so it stays steady above a burner or over a collecting vessel. Its shaft locks into a bosshead on a vertical support rod, and the round jaws close around the neck or body of the apparatus. Matching the span to the vessel matters: the 25–60 mm spans suit test tubes and flask necks, while the 80–150 mm spans take larger flasks and columns.

The 18/10 grade of stainless steel is corrosion-resistant and wipes clean after spills, so this clamp is a practical choice for teaching labs, research benches and any chemistry lab equipment set that sees daily use. Tighten the jaws only until the glassware is held firmly, because over-tightening metal jaws can crack glass. Where glass is thin-walled, a strip of rubber or cloth between jaw and vessel spreads the pressure.

What to Specify When Ordering

• Span d — choose 25, 40, 60, 80, 100, 120 or 150 mm to fit the diameter of your apparatus.
• Shaft diameter — the 150 mm clamps have a 10 mm shaft and the 180 mm clamps a 12 mm shaft; check that your bossheads accept it.
• Quantity per size — most labs mix small and large spans, so state the number needed of each.
• Stand parts — add bossheads and stand bases from the list below if you are equipping new stands.

OEM Manufacturer

Jain Scientific Equipments Private Limited, trading as ScienceLab, is the original equipment manufacturer (OEM) of this stainless steel retort clamp and makes the full size range at its own licensed factory at Saha, Ambala, Haryana, India. Because the clamps come direct from the factory, laboratories, colleges, distributors and importers in India and international markets can mix sizes in one order and deal with the maker for repeat supplies. Ask us about replacement parts for clamps already in service. More about the company is on the ScienceLab profile page.

Related Retort Clamps and Stand Parts

A clamp, a bosshead and a stand base together make a complete lab stand. These items work with the standard stainless clamp:

• Bossheads 18/10 Stainless Steel — connects the clamp shaft to the support rod.
• Stand bases 18/10 Stainless Steel — a matching stainless base for the vertical rod.
• Foot For Rods, Stainless Steel 18/10 — another way to stand a support rod upright.
• Retort Clamp Special 3-Prongs, 18/10-Stainless Steel — silicone-coated fingers for a gentler hold on glass.
• Retort Clamp Special 4-Prongs — four fingers for extra stability on larger vessels.

Compare every design in the Retort Clamp category.

Frequently Asked Questions

What sizes does the Retort Clamp Standard 18/10 Stainless Steel come in?
The Retort Clamp Standard 18/10 Stainless Steel comes in seven sizes: 150 mm long with a 10 mm shaft and spans of 25, 40 or 60 mm, and 180 mm long with a 12 mm shaft and spans of 80, 100, 120 or 150 mm.

What material is the standard retort clamp made from?
The Retort Clamp Standard (SLE/RC/01) is made from 18/10 stainless steel, a chromium-nickel grade that resists rust and can be wiped clean after chemical splashes, and it has round jaws for holding cylindrical apparatus.

Will the standard retort clamp fit my existing bosshead?
The standard stainless steel retort clamp has a 10 mm shaft on the 150 mm sizes and a 12 mm shaft on the 180 mm sizes. Check that your bosshead opening accepts that diameter, or order matching ScienceLab bossheads together with the clamps.

Who manufactures the Retort Clamp Standard 18/10 Stainless Steel?
Jain Scientific Equipments Pvt Ltd (ScienceLab) manufactures this retort clamp as the OEM at its own licensed factory at Saha, Ambala, Haryana, India, and supplies it directly to laboratories, institutions, dealers and importers.

How do I stop the retort clamp from cracking glassware?
Close the round jaws of the standard retort clamp gently until the vessel no longer slips, then stop, because over-tightening metal jaws on glass can cause cracks. For thin-walled glassware, a strip of rubber or cloth between jaw and glass spreads the pressure.

What does a quotation for standard retort clamps need?
A quotation for the Retort Clamp Standard 18/10 Stainless Steel should list the span sizes and the quantity of each, whether bossheads or stand bases are also needed, and the delivery location. Send the details via the contact page for a direct quote from the manufacturer.

Request a Quote

Send your size list for the Retort Clamp Standard 18/10 Stainless Steel through the contact page, or add it to the enquiry cart with any stand parts you need. Quotes are issued direct by ScienceLab as the manufacturer, and bulk laboratory or dealer orders are welcome.

Last updated: 24 September 2026

Retort Clamp Special 3-Prongs, 18/10-Stainless Steel (Product Code: SLE/RC/02) is a three-finger laboratory clamp used to hold glassware of different diameters on a support stand. Its stainless steel fingers carry a silicone coating that cushions the glass, and it comes 190 mm long on a 12 mm shaft with a span of 0–80 mm or 0–120 mm. It is made by Jain Scientific Equipments Pvt Ltd (ScienceLab), an OEM manufacturer, at its own factory in Ambala, India.

Specifications

What Is the 3-Prong Special Retort Clamp Used For?

Three fingers close on an object from three directions, centring round-bottom flasks, separating funnels, condensers and columns more naturally than a two-jaw clamp. Because the span opens from zero, the 0–80 mm version holds slim tubes as well as medium flasks, while the 0–120 mm version reaches wider vessels. That range lets one clamp serve many setups in chemistry lab glassware work, from distillation to filtration.

The silicone coating on each finger grips without scratching and spreads the load on glass, cushioning it without extra padding. Mount the 12 mm shaft in a bosshead, position the clamp before tightening, and check that the vessel hangs straight before adding liquid or heat. Keep the coated fingers away from direct flame.

What to Specify When Ordering

• Span version — 0–80 mm or 0–120 mm, based on the widest vessel you need to hold.
• Quantity — the number of clamps per bench or per stand.
• Bossheads — confirm that yours accept a 12 mm shaft, or add stainless bossheads to the order.

OEM Manufacturer

This 3-prong clamp comes from ScienceLab, the trade name of Jain Scientific Equipments Private Limited, which is its OEM and produces it at the company's own licensed factory at Saha, Ambala, Haryana, India. Research laboratories, universities, schools, dealers and importers in India and international markets buy it direct from the manufacturer rather than through a trading house. For spare parts on clamps already in use, just ask us. Read about the company on the ScienceLab profile.

Related Retort Clamps and Stand Parts

These stainless fittings and alternative clamps complete a setup built around the 3-prong special clamp:

• Bosshead Swivel Type, 18/10 Stainless Steel — lets the clamp be set at an angle, useful for condensers.
• Bosshead Cross Type 18/10 Stainless Steel — a fixed right-angle connection to the support rod.
• Base Frame tube, 18/10 Stainless Steel — for frame setups that carry several clamps.
• Retort Clamp Standard 18/10 Stainless Steel — a round-jaw alternative in seven fixed spans.
• Retort Clamp Special 4-Prongs — adds a fourth finger for larger or heavier vessels.

See the complete Retort Clamp range for other jaw types.

Frequently Asked Questions

What sizes is the Retort Clamp Special 3-Prongs available in?
The Retort Clamp Special 3-Prongs, 18/10-Stainless Steel is available in two versions, both 190 mm long with a 12 mm shaft: one with a 0–80 mm span and one with a 0–120 mm span.

Why are the fingers of this 3-prong clamp silicone coated?
The fingers of the Retort Clamp Special 3-Prongs carry a silicone coating so they grip glassware firmly without metal-to-glass contact, which helps prevent scratches and spreads the pressure on thin-walled flasks and tubes.

How does the 3-prong special clamp differ from a standard retort clamp?
The Retort Clamp Special 3-Prongs uses three silicone-coated fingers that centre round vessels and open from zero, whereas a standard retort clamp has bare round jaws in fixed span sizes. The 3-prong design suits mixed diameters on one stand.

Who manufactures the Retort Clamp Special 3-Prongs?
Jain Scientific Equipments Pvt Ltd (ScienceLab) manufactures the Retort Clamp Special 3-Prongs, 18/10-Stainless Steel as the OEM, making it at its own licensed factory at Saha, Ambala, Haryana, India, and supplying it directly to labs, dealers and importers.

Can the 3-prong special clamp be used near a burner?
The Retort Clamp Special 3-Prongs can hold glassware in a heated setup, but keep its silicone-coated fingers out of direct flame and let hot glass cool before adjusting the clamp. Position it around the neck of the vessel, away from the hottest zone.

How do I request a quote for the 3-prong special retort clamp?
To request a quote for the Retort Clamp Special 3-Prongs, state the span version (0–80 or 0–120 mm), the quantity and any bossheads or stand parts needed, then send it through the contact page. The manufacturer replies directly.

Request a Quote

Add the Retort Clamp Special 3-Prongs, 18/10-Stainless Steel to the enquiry cart or write to us through the contact page with your span choice and quantity. Every quote comes directly from ScienceLab as the manufacturer.

Last updated: 24 September 2026

Retort Clamp 3 Prongs (Product Code: SLE/RC/03) is a red PVC three-prong clamp used to hold flasks, tubes and similar apparatus on a laboratory stand in school and college practicals. Its span width is set with two regulating screws that adjust independently, and the clamp is 140 mm long with a diameter range listed as 12–100 mm. It is manufactured by Jain Scientific Equipments Pvt Ltd (ScienceLab), an OEM, at its own factory in Ambala, India.

Specifications

What Is the 3 Prong Retort Clamp Used For?

This clamp holds round apparatus such as flasks, test tubes and small columns steady on a retort stand during titration, filtration and demonstration setups. Because each regulating screw adjusts independently, the span can be set so that an off-centre or unevenly shaped item is gripped evenly, and the clamp can sit exactly where the vessel needs support.

The red PVC finish makes the clamp easy to spot on a crowded bench, a small but real help in busy practical classes, and it is an everyday piece of chemistry lab equipment in schools. As a PVC item, it should be kept clear of burner flames and hot plates; for heated work choose a stainless steel clamp instead. Tighten both screws evenly and check the hold before letting go of the vessel.

What to Specify When Ordering

• Quantity — the number of clamps needed per stand or per bench.
• Vessel sizes — share the diameters you need to hold so we can confirm them against the listed 12–100 mm range.
• Stand parts — add a stand base or other clamps from the list below if you are setting up new stations.

OEM Manufacturer

ScienceLab is the trading name of Jain Scientific Equipments Private Limited, the OEM that makes the Retort Clamp 3 Prongs at its own licensed factory at Saha, Ambala, Haryana, India. The company is a registered MSME enterprise (Udyam UDYAM-HR-01-0003714) and handles export shipments under Importer-Exporter Code AAECJ8618A issued by DGFT. Schools, colleges, distributors and importers in India and international markets therefore buy from the maker itself, with quotations and repeat orders handled at source. See the ScienceLab company profile for more.

Related Retort Clamps

Other clamps and stand parts that suit the same practical setups:

• Three Prong Swivel Clamp — a three-prong design whose head can be angled.
• Retort Clamp Three Finger — another three-finger clamp for general stand work.
• 3 Finger Clamps With Shaft — a chromium-plated option with PVC-coated fingers.
• Universal Clamp — for items that do not suit a prong-type grip.
• A-Shape Retort Stand Base — a stable base for the support rod.

All clamp styles are listed in the Retort Clamp category.

Frequently Asked Questions

What is the Retort Clamp 3 Prongs made of?
The Retort Clamp 3 Prongs (SLE/RC/03) is listed in red PVC. Because PVC softens with heat, keep this clamp away from burner flames and hot plates, and choose a stainless steel clamp for heated setups.

How is the span of the Retort Clamp 3 Prongs adjusted?
The span width of the Retort Clamp 3 Prongs is set with 2 regulating screws that adjust independently, so the grip can be centred on the vessel or offset where a setup needs it. Tighten both evenly before releasing the apparatus.

What size of apparatus does the Retort Clamp 3 Prongs hold?
The Retort Clamp 3 Prongs is 140 mm long and is listed with a D/Ø range of 12–100 mm. To confirm that a particular flask or tube will fit, send its diameter through the contact page before ordering.

Who manufactures the Retort Clamp 3 Prongs?
The Retort Clamp 3 Prongs is manufactured by Jain Scientific Equipments Pvt Ltd (ScienceLab), the OEM, at its own licensed factory at Saha, Ambala, Haryana, India. Quotations and repeat orders come straight from the manufacturer.

Is the Retort Clamp 3 Prongs suitable for school labs?
Yes, the Retort Clamp 3 Prongs suits school and college practicals such as titration and filtration setups where no direct heat is applied. Its red PVC finish is easy to spot on shared benches, and its two screws make adjustment simple for students.

Can the Retort Clamp 3 Prongs be supplied for export?
Yes, ScienceLab supplies the Retort Clamp 3 Prongs to buyers in India and international markets. Share the quantity, destination and any matching stand parts through the contact page, and the manufacturer will quote for the complete consignment.

Request a Quote

For a price on the Retort Clamp 3 Prongs, use the contact page or place it in the enquiry cart with other stand parts. Quotes come straight from ScienceLab as the manufacturer, whether for one lab or a dealer's stock.

Last updated: 24 September 2026

3 Finger Clamps With Shaft (Product Code: SLE/RC/04) is a chromium-plated three-finger clamp on its own shaft, used to hold slim glassware such as test tubes, burettes and small flasks on a laboratory stand. Its PVC-coated fingers open to a span of 0–35 mm or 0–60 mm, set by two regulating screws that adjust independently, on a 150 mm clamp with a 10 mm shaft. It is made by Jain Scientific Equipments Pvt Ltd (ScienceLab), an OEM manufacturer, at its own factory in Ambala, India.

Specifications

What Is the 3 Finger Clamp With Shaft Used For?

With spans that start at zero, these clamps are sized for slim items: the 0–35 mm version suits test tubes, burettes and narrow condensers, while the 0–60 mm version takes flask necks and small bottles. The shaft slots into a bosshead on a support rod, and the independent regulating screws let the fingers close evenly around the item.

Chromium plating gives the metal body a bright surface that is easy to wipe down, while the PVC coating on the fingers keeps bare metal off the glass. In titration practicals the 0–35 mm version can also serve as a burette clamp. Keep the PVC-coated fingers away from open flames, and release the screws before removing hot glassware.

What to Specify When Ordering

• Span version — 0–35 mm for tubes and burettes, or 0–60 mm for flask necks and small bottles.
• Quantity — how many clamps of each span per bench or stand.
• Bossheads — check that your fittings accept a 10 mm shaft.
• Stands or burette holders — add items from the related list if you are equipping new titration stations.

OEM Manufacturer

Jain Scientific Equipments Private Limited, known by its brand ScienceLab, is the OEM of the 3 Finger Clamps With Shaft and produces them at its own licensed factory at Saha, Ambala, Haryana, India. School science departments, university labs, stockists and importers in India and international markets get these clamps factory-direct instead of from a reseller. Spares and repeat batches are organised by the manufacturer, so ask us whenever you need them. Visit the ScienceLab company profile to learn more.

Related Retort Clamps and Holders

These holders and clamps are often ordered with the 3 Finger Clamps With Shaft:

• Burette Clamps — a dedicated holder for titration burettes.
• Burette Clamps Light Weight — a lighter burette holder for student benches.
• Retort Clamp Three Finger — a three-finger alternative from the chemistry range.
• Vertical Stand With 3 Clamps — a ready stand when several items must be held at once.
• Retort Clamp 3 Prongs — a red PVC clamp with a wider listed range.

Browse the Retort Clamp category for every clamp style.

Frequently Asked Questions

What spans are available for the 3 Finger Clamps With Shaft?
The 3 Finger Clamps With Shaft come in two spans, 0–35 mm and 0–60 mm, both on a 150 mm long clamp with a 10 mm shaft. Choose the smaller one for test tubes and burettes and the larger one for flask necks.

What is the finish of the 3 Finger Clamps With Shaft?
The 3 Finger Clamps With Shaft have a chromium-plated body with PVC-coated fingers. The plating keeps the metal surface bright and easy to wipe, and the PVC coating stops bare metal from touching the glassware being held.

How do the regulating screws on the 3 Finger Clamps With Shaft work?
The span width of the 3 Finger Clamps With Shaft is adjusted by 2 regulating screws that work independently, letting you close the fingers evenly around a vessel or offset the grip slightly where a setup is not perfectly aligned.

Who manufactures the 3 Finger Clamps With Shaft?
Jain Scientific Equipments Pvt Ltd (ScienceLab) manufactures the 3 Finger Clamps With Shaft as the OEM, producing them at its own licensed factory at Saha, Ambala, Haryana, India, and quoting directly to laboratories, dealers and importers.

Will the 3 Finger Clamps With Shaft fit my bosshead?
The 3 Finger Clamps With Shaft have a 10 mm shaft, so they fit a bosshead whose opening accepts that diameter. If you are unsure about your existing fittings, send their details through the contact page and we will advise.

What should an enquiry for 3 Finger Clamps With Shaft include?
An enquiry for 3 Finger Clamps With Shaft should state how many clamps of each span (0–35 or 0–60 mm) you need, any bossheads or stands to go with them, and the delivery location in India or abroad, so the manufacturer can quote in one step.

Request a Quote

To order the 3 Finger Clamps With Shaft, send your span choice and quantity through the contact page or add the item to the enquiry cart. ScienceLab replies as the manufacturer with a direct quotation.

Last updated: 24 September 2026

Retort Clamp Special 4-Prongs (Product Code: SLE/RC/05) is a four-finger stainless steel laboratory clamp used to hold larger or heavier round vessels, such as big flasks and wide columns, firmly on a retort stand. Made from 18/10 stainless steel with silicone-coated fingers and a 12 mm shaft, it comes in three sizes with spans of 0–120 mm, 20–100 mm or 50–150 mm. It is manufactured by Jain Scientific Equipments Pvt Ltd (ScienceLab), an OEM, at its own factory in Ambala, India.

Specifications

What Is the 4-Prong Special Retort Clamp Used For?

A fourth finger spreads the holding force around more of the vessel, so the clamp resists tilting when it carries a large round-bottom flask, a wide chromatography column or a full separating funnel. The 150 mm size with a 0–120 mm span covers everything from narrow necks to mid-sized bodies, while the two 190 mm sizes reach further from the rod and are set for mid-range (20–100 mm) or wide (50–150 mm) vessels.

Silicone-coated fingers keep metal off the glass and add grip on smooth surfaces. For heavy loads, mount the clamp low on the support rod, tighten the bosshead fully before adding liquid, and keep the coated fingers clear of direct flame. Checking the stand for wobble before starting a long run is a good habit in any teaching or research lab.

What to Specify When Ordering

• Size — 150 mm with 0–120 mm span, 190 mm with 20–100 mm span, or 190 mm with 50–150 mm span.
• Vessel range — note the smallest and largest diameters you need to hold.
• Bossheads — confirm that they accept a 12 mm shaft.
• Quantity — the number required of each size.

OEM Manufacturer

ScienceLab is the brand of Jain Scientific Equipments Private Limited, the original equipment manufacturer (OEM) of the Retort Clamp Special 4-Prongs, which makes all three sizes at its own licensed factory at Saha, Ambala, Haryana, India. Orders from laboratories, institutions, distributors and importers in India and international markets are dispatched from that factory, so the buyer deals with the maker throughout. Questions about spare parts or repeat orders can come straight to us. The ScienceLab profile explains more about the company.

Related Retort Clamps and Stand Parts

Clamp, boss head and stand base should be chosen together. These items suit setups built around the 4-prong special clamp:

• Retort Clamp Four Finger — another four-finger clamp from the chemistry range.
• Retort Clamp Special 3-Prongs, 18/10-Stainless Steel — a three-finger version for slimmer vessels.
• Adjustable Clamp Holder — for connecting the clamp to a support rod.
• A-Shape Retort Stand Base — a stand base for mounting the support rod.
• Fisher Clamp — an alternative clamp design for general stand work.

The full Retort Clamp category lists every jaw and prong style.

Frequently Asked Questions

What sizes does the Retort Clamp Special 4-Prongs come in?
The Retort Clamp Special 4-Prongs comes in three sizes, all with a 12 mm shaft: 150 mm long with a 0–120 mm span, 190 mm long with a 20–100 mm span, and 190 mm long with a 50–150 mm span.

Why choose a 4-prong clamp instead of a 3-prong clamp?
A 4-prong clamp such as the Retort Clamp Special 4-Prongs grips a vessel at four points instead of three, spreading the load and resisting tilt, which helps with large flasks, wide columns and other heavy or top-heavy apparatus.

What are the fingers of the Retort Clamp Special 4-Prongs coated with?
The fingers of the Retort Clamp Special 4-Prongs have a silicone coating over the 18/10 stainless steel. The coating cushions glass and improves grip on smooth surfaces, and it should be kept away from direct flame.

Who manufactures the Retort Clamp Special 4-Prongs?
The Retort Clamp Special 4-Prongs is manufactured by Jain Scientific Equipments Pvt Ltd (ScienceLab), the OEM, at its own licensed factory at Saha, Ambala, Haryana, India. Laboratories and dealers receive quotations directly from the manufacturer.

Which size of the 4-prong special clamp should I choose?
For the Retort Clamp Special 4-Prongs, pick the 0–120 mm size if your vessels vary widely, the 20–100 mm size for mid-sized flasks, or the 50–150 mm size for wide vessels. Measure the widest point you will clamp before ordering.

How can I get a quotation for the Retort Clamp Special 4-Prongs?
For a quotation on the Retort Clamp Special 4-Prongs, list the sizes and quantities needed, any bossheads or stand bases, and the delivery location, then send them via the contact page. ScienceLab replies directly as the manufacturer.

Request a Quote

Put the Retort Clamp Special 4-Prongs in the enquiry cart or contact us through the contact page with your size choices. Quotations come directly from ScienceLab, the manufacturer, for single labs and bulk orders alike.

Last updated: 24 September 2026

Retort Clamp with Bosshead, Cork Jaws (Product Code: SLE/LC/16) is a diecast alloy laboratory clamp with cork-lined jaws, used to hold flasks, condensers and tubes on a retort stand rod. It comes complete with a bosshead that accommodates rods up to 15 mm in diameter, giving a lab stand clamp and boss head in one item, while the cork lining cushions glassware. It is made by Jain Scientific Equipments Pvt Ltd (ScienceLab), an OEM manufacturer, at its own factory in Ambala, India.

Specifications

What Is the Cork-Jaw Retort Clamp with Bosshead Used For?

Cork is a traditional jaw lining because it is slightly compressible and a poor conductor of heat, so it moulds gently around a flask neck or condenser and cushions glass that is warm from a heating setup. To mount the clamp, slide the bosshead onto a stand rod of up to 15 mm diameter, tighten it at the working height, then close the cork-lined jaws around the apparatus until it no longer turns.

Because the clamp and bosshead come together, a teacher or technician can equip a new stand in one step, and the diecast alloy body suits everyday school, college and research use as part of a chemistry lab equipment set. Cork liners can dry out over the years, so wipe them with a dry cloth rather than solvents and keep the clamp away from strong heat when stored.

OEM Manufacturer

This cork-jaw clamp is manufactured by Jain Scientific Equipments Private Limited (CIN U29309HR2020PTC087597), which trades as ScienceLab and acts as its OEM. Production takes place at the company's own licensed factory at 449, HSIIDC Industrial Area, Saha, Ambala, Haryana (Factory Licence AMB-ONLINE-CHD-J-414), and finished clamps go directly to laboratories, schools, dealers and importers in India and international markets. Buying from the maker keeps quotations, repeat orders and spare-part questions in one place, so just ask us. More detail is on the ScienceLab company profile.

Related Retort Clamps and Stands

These items complete a stand built around the cork-jaw clamp:

• A-Shape Retort Stand Base — a base for the support rod the bosshead slides onto.
• Retort Clamp with Bosshead, Rubber Jaws — the same idea with rubber-lined jaws for grip on smooth glass.
• Retort Clamp, Cork Jaws — a four-prong cork-jaw clamp without a bosshead.
• Burette Stand with Clamp & Bosshead — a complete stand for titration work.
• Thermometer Clamp — holds a thermometer beside the clamped flask.

Compare all designs in the Retort Clamp category.

Frequently Asked Questions

What rod size does the bosshead on this cork-jaw clamp fit?
The bosshead on the Retort Clamp with Bosshead, Cork Jaws (SLE/LC/16) accommodates support rods up to 15 mm in diameter. Measure the rods on your existing retort stands before ordering to confirm they are within that size.

Why choose cork-lined jaws on a retort clamp?
Cork-lined jaws, as on the Retort Clamp with Bosshead, Cork Jaws, are slightly compressible and insulating, so they cushion glassware, spread the clamping pressure and suit apparatus that is warm from a heating setup, all without metal-to-glass contact.

What is the Retort Clamp with Bosshead, Cork Jaws made from?
The Retort Clamp with Bosshead, Cork Jaws has a diecast alloy body with cork-lined jaws, and it comes complete with a bosshead for mounting on a retort stand rod of up to 15 mm diameter.

Who manufactures the Retort Clamp with Bosshead, Cork Jaws?
Jain Scientific Equipments Pvt Ltd (ScienceLab) manufactures the Retort Clamp with Bosshead, Cork Jaws as the OEM at its own licensed factory at Saha, Ambala, Haryana, India, and supplies it directly to laboratories, dealers and importers.

How should the cork jaws be cared for?
Clean the cork jaws of the Retort Clamp with Bosshead with a dry or lightly damp cloth, avoid soaking them in solvents, and store the clamp away from strong heat so the cork stays resilient. Replace the clamp if the lining starts to crumble.

What should a quotation request for this cork-jaw clamp include?
A quotation request for the Retort Clamp with Bosshead, Cork Jaws should give the quantity, your stand rod diameter, any stands or other clamps needed and the delivery location. Send it via the contact page for a direct manufacturer's quote.

Request a Quote

Ask for a price on the Retort Clamp with Bosshead, Cork Jaws through the contact page, or add it to the enquiry cart with any stands you need. ScienceLab quotes as the manufacturer for single labs, institutions and dealer orders.

Last updated: 24 September 2026

Retort Clamp with Bosshead, Rubber Jaws (Product Code: SLE/LC/15) is a rubber-lined diecast alloy clamp used to grip smooth glassware, plastic bottles and tubing firmly on a laboratory retort stand. Its bosshead takes rods up to 15 mm in diameter, and the rubber lining adds friction so smooth, slippery items stay put during room-temperature work. It is produced by Jain Scientific Equipments Pvt Ltd (ScienceLab), an OEM manufacturer, at its own factory in Ambala, India.

Specifications

What Is the Rubber-Jaw Retort Clamp with Bosshead Used For?

Rubber linings give a firm, non-slip hold on smooth and slightly wet surfaces, which makes this clamp a good fit for separating funnels, measuring cylinders, gas jars during collection over water, and plastic bottles or tubing that a hard jaw might dent. The bosshead lets the whole unit be set at any height on a rod of up to 15 mm diameter.

Rubber softens with heat and can swell on contact with some organic solvents and oils, so this version is suited to room-temperature work; for warm glassware the cork-jaw version is the usual choice. Inspect the linings from time to time and clean them with water and a mild detergent rather than solvent. Tighten the bosshead first, then the jaws, so the vessel is never left hanging on a loose clamp.

What to Specify When Ordering

• Quantity — the number of clamps per stand or bench.
• Rod diameter — confirm your stand rods are no thicker than 15 mm.
• Jaw lining — rubber for grip at room temperature, or cork for warm apparatus; many labs order some of each.

OEM Manufacturer

The rubber-jaw clamp is an OEM product of ScienceLab, the trading name of Jain Scientific Equipments Private Limited, and is manufactured at the company's own licensed factory at Saha, Ambala, Haryana, India. Educational institutions, research labs, stockists and importers in India and international markets receive it straight from that factory rather than through a trader. If you need spare parts or a repeat batch to match earlier supplies, the manufacturer handles it directly, so ask us. Background on the company is available on the ScienceLab profile.

Related Retort Clamps and Stand Items

Items that pair with the rubber-jaw clamp in wet-chemistry and gas-collection setups:

• Retort Clamp with Bosshead, Cork Jaws — the cork-lined version for warm apparatus.
• Retort Clamp, Rubber Jaws — a rubber-jaw clamp on its own rod, for use with a separate boss.
• Elastic Clamps for Rubber Pipes (Mohr Clamp) — for pinching rubber tubing in the same setup.
• A-Shape Retort Stand Base — a base for the support rod.
• Burette Stand with Clamp & Bosshead — a ready stand for titrations.

Every clamp style is listed in the Retort Clamp category.

Frequently Asked Questions

What rod diameter does the rubber-jaw clamp's bosshead accept?
The bosshead of the Retort Clamp with Bosshead, Rubber Jaws (SLE/LC/15) accommodates rods up to 15 mm in diameter, so it can be fixed at any height on a retort stand rod within that size.

When should I choose rubber jaws over cork jaws?
Choose the Retort Clamp with Bosshead, Rubber Jaws when you need a firm, non-slip grip on smooth or damp glassware, plastic bottles or tubing at room temperature; choose the cork-jaw version when the apparatus will be warm.

Can the rubber-jaw clamp be used near heat or solvents?
The rubber lining of the Retort Clamp with Bosshead, Rubber Jaws should be kept away from burner flames and hot surfaces, and out of prolonged contact with organic solvents or oils, which can swell or soften rubber.

Who manufactures the Retort Clamp with Bosshead, Rubber Jaws?
The Retort Clamp with Bosshead, Rubber Jaws is manufactured by Jain Scientific Equipments Pvt Ltd (ScienceLab), the OEM, at its own licensed factory at Saha, Ambala, Haryana, India, with quotations issued directly by the manufacturer.

What is the body of the rubber-jaw clamp made of?
The Retort Clamp with Bosshead, Rubber Jaws has a diecast alloy body with rubber-lined jaws and comes complete with a bosshead, giving a compact clamp that mounts straight onto a laboratory stand rod.

Is the rubber-jaw clamp available for bulk or export orders?
Yes, ScienceLab supplies the Retort Clamp with Bosshead, Rubber Jaws in laboratory, institutional and dealer quantities for India and international markets. Share the quantity and destination through the contact page for a manufacturer's quotation.

Request a Quote

To price the Retort Clamp with Bosshead, Rubber Jaws, send your quantity via the contact page or add it to the enquiry cart. As the manufacturer, ScienceLab prepares the quotation itself, including any matching stands you list.

Last updated: 24 September 2026

Retort Clamp, Cork Jaws (Product Code: SLE/LC/17) is a four-prong laboratory clamp with cork-lined jaws, used to hold items from 2 to 90 mm in diameter, from thin tubes to flasks, on a retort stand. It has a blue coated finish, an overall length of 245 mm and a 145 mm rod, and its jaw design keeps a firm grip at every angle of opening. It is made by Jain Scientific Equipments Pvt Ltd (ScienceLab), an OEM manufacturer, at its own factory in Ambala, India.

Specifications

What Is the Four-Prong Cork-Jaw Retort Clamp Used For?

The wide 2–90 mm range means one clamp can hold a thin tube for one experiment and a mid-sized round-bottom flask for the next, cutting down the number of clamp types a lab has to stock. Four cork-lined prongs close evenly around the item, and because the jaw geometry keeps its grip at all angles of opening, small items are held as firmly as larger ones.

Cork cushions glass and insulates against moderate warmth, and on this clamp the liners are well secured to the jaws, so they stay put through repeated tightening. The 145 mm rod fits into a boss or clamp holder on a retort stand, while the blue coating protects the metal and makes the clamp easy to pick out on a shared bench. Keep the cork away from open flame and wipe it with a dry cloth after use.

What to Specify When Ordering

• Quantity — the number of clamps needed per stand or bench.
• Mounting — the clamp fixes by its 145 mm rod, so each one needs a boss or clamp holder on the stand.
• Largest item — check that your widest vessel is within the 90 mm capacity; for wider items see other clamps in the category.

OEM Manufacturer

ScienceLab, the trading name of Jain Scientific Equipments Private Limited, is the OEM of the Retort Clamp, Cork Jaws and makes it at its own licensed factory at Saha, Ambala, Haryana, India. Schools, college chemistry departments, industrial QC labs, dealers and importers in India and international markets are supplied factory-direct, with quotations prepared by the manufacturer. For extra clamps to match an earlier order, or for spare-part questions, ask us. The ScienceLab company profile has more about the business.

Related Retort Clamps and Holders

Holders, bases and alternative clamps that work with the four-prong cork-jaw clamp:

• Adjustable Clamp Holder — fixes the clamp rod to the stand.
• A-Shape Retort Stand Base — a base for the vertical support rod.
• Retort Clamp with Bosshead, Cork Jaws — cork jaws with a bosshead included.
• Retort Clamp, Rubber Jaws — the rubber-lined alternative for smooth or damp items.
• Retort Clamp Four Finger — another four-finger design from the chemistry range.

Compare every clamp in the Retort Clamp category.

Frequently Asked Questions

What size of items does the Retort Clamp, Cork Jaws hold?
The Retort Clamp, Cork Jaws (SLE/LC/17) accepts articles from 2 to 90 mm in diameter, so it can hold narrow tubes as well as flasks and bottles of moderate size, with a firm grip at all angles of opening.

What are the dimensions of the Retort Clamp, Cork Jaws?
The Retort Clamp, Cork Jaws has an overall length of 245 mm and a rod length of 145 mm. The rod is fixed into a boss or clamp holder on a retort stand to position the four cork-lined prongs.

Does the Retort Clamp, Cork Jaws include a bosshead?
The Retort Clamp, Cork Jaws is a clamp on a 145 mm rod and is not listed with a bosshead. Use a separate boss or adjustable clamp holder, or choose the Retort Clamp with Bosshead, Cork Jaws if you want both together.

Who manufactures the Retort Clamp, Cork Jaws?
Jain Scientific Equipments Pvt Ltd (ScienceLab) manufactures the Retort Clamp, Cork Jaws as the OEM at its own licensed factory at Saha, Ambala, Haryana, India, and sells it factory-direct to laboratories, schools, dealers and importers.

How should I look after the cork jaws?
Wipe the cork jaws of the Retort Clamp, Cork Jaws with a dry cloth after use, avoid soaking them in water or solvents, and keep them away from open flame. The liners are well secured to the jaws, so they stay in place during normal tightening.

What details should I send for a Retort Clamp, Cork Jaws quote?
For a Retort Clamp, Cork Jaws quote, send the quantity, whether you also need bosses, clamp holders or stand bases, and the delivery location in India or abroad through the contact page. The manufacturer replies with a direct quotation.

Request a Quote

Get a quotation for the Retort Clamp, Cork Jaws by writing through the contact page or adding it to the enquiry cart with any stand parts. ScienceLab quotes as the manufacturer, whether you need a few clamps or a full lab fit-out.

Last updated: 24 September 2026

Retort Clamp, Rubber Jaws (Product Code: SLE/LC/18) is a laboratory clamp with rubber-lined diecast jaws, used to hold flasks, bottles and tubes up to 90 mm across on a retort stand. It is mounted on a 135 mm rod of 8 mm diameter, measures 250 mm overall, and its clamping rod works through swivels set into the jaws so they settle evenly on the item. It is manufactured by Jain Scientific Equipments Pvt Ltd (ScienceLab), an OEM, at its own factory in Ambala, India.

Specifications

What Is the Rubber Jaw Retort Clamp Used For?

A 90 mm jaw capacity covers a wide range of everyday glassware on a student bench, including conical flasks, reagent bottles, measuring cylinders and boiling tubes. The swivels in the jaws let each jaw pivot slightly as the clamping rod is tightened, so the rubber pads sit flat against curved or tapered surfaces instead of pinching at one point.

Before setting up, check that your boss or clamp holder grips an 8 mm rod securely; the 135 mm rod length decides how far the vessel sits from the stand upright. The rubber lining grips smooth glass well but should be kept away from flames, hot plates and prolonged solvent contact. Used this way, it is a common piece of chemistry lab equipment on school and college benches.

OEM Manufacturer

Jain Scientific Equipments Private Limited, whose brand is ScienceLab, is the OEM of the Retort Clamp, Rubber Jaws and produces it at its own licensed factory at Saha, Ambala, Haryana, India. That factory ships directly to teaching labs, research institutes, lab-supply dealers and importers in India and international markets, so pricing, repeat orders and spares are all handled by the maker. Ask us if you need clamps to match ones supplied earlier. Company details are on the ScienceLab profile.

Related Retort Clamps and Holders

These items fit alongside the rubber jaw clamp on the same stand:

• Adjustable Clamp Holder — to fix the clamp rod to a stand.
• Retort Clamp with Bosshead, Rubber Jaws — rubber jaws with a bosshead included.
• Retort Clamp, Cork Jaws — a four-prong cork-lined clamp for warmer work.
• Universal Clamp — for awkwardly shaped apparatus.
• Elastic Clamps for Rubber Pipes (Mohr Clamp) — to control tubing connected to the clamped vessel.

Browse the full Retort Clamp category for other jaw linings and sizes.

Frequently Asked Questions

What is the jaw capacity of the Retort Clamp, Rubber Jaws?
The Retort Clamp, Rubber Jaws (SLE/LC/18) has a jaw capacity of 90 mm, so it can hold items up to that diameter, from test tubes and boiling tubes to conical flasks and reagent bottles.

How is the Retort Clamp, Rubber Jaws mounted on a stand?
The Retort Clamp, Rubber Jaws is mounted on a 135 mm rod of 8 mm diameter. Fix that rod in a boss or clamp holder on your retort stand, making sure the fitting grips an 8 mm rod securely before loading the clamp.

What do the swivels in the jaws of this clamp do?
In the Retort Clamp, Rubber Jaws, the clamping rod operates through swivels mounted in the jaws, which lets the rubber-lined jaws settle evenly against the item as they close instead of pressing at a single point.

Who manufactures the Retort Clamp, Rubber Jaws?
The Retort Clamp, Rubber Jaws is manufactured by Jain Scientific Equipments Pvt Ltd (ScienceLab), the OEM, at its own licensed factory at Saha, Ambala, Haryana, India. Laboratories, dealers and importers buy it direct from the manufacturer.

What is the overall length of the Retort Clamp, Rubber Jaws?
The Retort Clamp, Rubber Jaws is 250 mm long overall and sits on a 135 mm mounting rod. Allow for this reach when planning how far the vessel will sit from the stand upright and from neighbouring equipment.

How do I get a quotation for the Retort Clamp, Rubber Jaws?
To get a quotation for the Retort Clamp, Rubber Jaws, send the quantity, any clamp holders or stands required and your delivery location through the contact page. ScienceLab, as the manufacturer, replies with a direct quote for India or international delivery.

Request a Quote

Enquire about the Retort Clamp, Rubber Jaws via the contact page, or add it to the enquiry cart together with holders and stands. Quotes come directly from ScienceLab, the manufacturer, for laboratories, institutions and resellers.

Last updated: 24 September 2026