Connected to a test engine by an exhaust gas hose, the Exhaust Gas Calorimeter finds how much heat the engine loses in its exhaust. Inside an insulated stainless steel tank, the gas passes through a counter-flow finned pipe heat exchanger. Four temperature sensors and a 0–160 L/h water flow meter feed digital displays through a measuring amplifier.
| Parameter | Detail |
|---|---|
| Heat exchanger | Counter-flow, finned pipe type, in an insulated stainless steel tank |
| Heat exchange area | 0.944 m² on the exhaust gas side; 0.141 m² on the water side |
| Exhaust gas temperature | 2 × 0–600 °C |
| Cooling water temperature | 2 × 0–200 °C |
| Water flow rate | 0–160 L/h (flow meter) |
| Instrumentation | 4 temperature sensors, flow meter, measuring amplifier with digital displays |
| Engine connection | Exhaust gas hose |
| Power supply | 230 V, 50 Hz, single phase |
| Size and weight | 600 × 600 × 1300 mm; approx. 103 kg |
| Product code | SLE/MCE/54 |
| Minimum order | 10 units |
| Dispatch | Usually within 7 to 10 working days |
| Manufacturer | ScienceLab (Jain Scientific Equipments Pvt Ltd), Ambala, India |
Setting up at the engine. Run the exhaust gas hose from the four stroke four cylinder petrol engine test bench to the calorimeter inlet. Start the water and set a steady flow on the flow meter before any exhaust passes through, then hold it steady so the outlet water stays well below boiling.
Exhaust heat by two routes. From the water side, students find the heat taken up from flow, specific heat and temperature rise. From the gas side, they use fuel flow from a manual volumetric fuel gauge plus the air flow, and the gas temperature fall. The gap between the two answers opens a discussion of heat lost through the tank.
Exchanger performance. Using the stated gas-side area of 0.944 m², students work out the overall heat transfer coefficient from the heat transferred and the log mean temperature difference. Repeating this at two or three water flow rates shows how flow changes heat transfer.
Petrol against diesel exhaust. Run the same test on the 4 stroke diesel engine and compare gas inlet temperatures and the exhaust share of fuel energy with the petrol results.
Heat passes from a gas to metal far less readily than from metal to water. Fins add surface on the exhaust side, giving 0.944 m² against 0.141 m² on the water side, which makes up for much of that weaker gas-side transfer.
Add the mass of air the engine draws in per minute to the mass of fuel it burns per minute. Air flow usually comes from the engine's air intake measurement and fuel flow from timing a known volume of fuel. That total, multiplied by the exhaust specific heat and temperature difference, gives the exhaust heat.
Many lab sheets assume a fixed value close to that of air. The calorimeter lets students check it: divide the heat taken up by the water by the gas mass flow and the fall in gas temperature across the exchanger. Comparing the two values is a good discussion point in the report.
Yes. Soot and other deposits insulate the fins, so less heat reaches the water and the gas leaves hotter, and the effect grows with running hours. Record the gas outlet temperature at one reference load each term. A steady rise shows that the exchanger needs cleaning as the supplied operating instructions describe.
The tank and finned pipe stay hot after the exhaust stops. Without flow, water standing in the exchanger can overheat and boil. Leave the water running until the outlet water temperature has fallen close to the inlet temperature, then shut it off.
It supplies the line for heat carried away by the exhaust. Put every line, from fuel heat to brake power, jacket cooling water and exhaust, in the same units per minute and as a percentage of fuel heat. Whatever is left after these lines is the unaccounted heat.
To request a quotation, send the product name, code and quantity through our contact page or add the item to your enquiry cart.
Last updated: 14 November 2026