DIY electronics kits on this page are the parts and boards students wire and measure themselves, from a first breadboard circuit to diode curves, transistor switching, capacitor charging and logic gate truth tables. School, college and vocational students use them in practicals and project work. The starter kit, circuit panels, diode boards, logic gate box, demonstration and capacitor kits and the reed relay module are made by ScienceLab in Ambala. The loose resistors, LEDs, capacitor, diodes, transistor, single Zener diode and light sensor module are supplied by ScienceLab, Ambala.
| Group | What it covers | Example products |
|---|---|---|
| First circuits on a breadboard | A solderless breadboard kit with transistors, LEDs, capacitors, a photo resistor, a buzzer and a teacher's guide, plus loose carbon resistors in different values and board-mounted LEDs for extending a build. | Fundamentals of Electronics, Carbon Resistance of Different Values, LED |
| Panel and module circuits | Components on their own panels with 4 mm sockets, joined by stackable leads, and modules that add a light sensor or a reed relay to a circuit. | Electricity Circuits Kit, Simple Circuit Module Light Dependent Resistor Board, Simple Circuit Module Reed Relay |
| Diode characteristics | Boards with built-in supplies and two meters for plotting forward and reverse curves, and a board-mounted Zener diode for breakdown and regulation tests. | PN Junction Diode, Zener Diode Experiment Circuit Board, Zener Diode |
| Rectifiers and transistors | Rectifier diodes for one-way conduction and turning AC into DC, an NPN transistor for switching, and a bench kit that pairs a transistor, Zener and diodes with a multimeter and meters. | Semiconductor Diodes (for high school), Transistor (for high school), Equipment Kit for Demonstrating Electrical Experiments |
| Capacitors and timing | A capacitor with two resistors and a power supply for comparing fast and slow charging curves, and a loose capacitor for charging, filtering and timing circuits. | Capacitor (Charging and Discharging), Capacitor |
| Digital logic | A plastic box of logic gate modules, each printed with its truth table, with inputs and outputs on coloured 4 mm sockets. | Logic Gate Apparatus |
Start students on the Fundamentals of Electronics kit, whose solderless breadboard lets them build, test and rebuild a circuit in one lesson. The Electricity Circuits Kit suits younger classes, since each part sits on its own panel and joins with stackable leads. Once a circuit works, ask students to swap one part, such as a resistor of another value, and predict the effect before testing it.
Move to measurement once students wire reliably. The PN Junction Diode and Zener Diode Experiment Circuit Board carry their own supply and two meters, so groups need no separate supply or meters and can spend the lesson on readings. The capacitor charging set gives a fast and a slow curve from its two resistors, and the Logic Gate Apparatus checks each gate against its printed truth table.
Turn the supply down to zero before switching on, raise it in small steps, and switch off before changing any connection. Check which way round each LED, diode and electrolytic capacitor goes before connecting it, keep leads untangled, and at the end of the lesson return each loose part to its marked box.
The PN Junction Diode and Zener Diode Experiment Circuit Board have built-in regulated supplies and two meters, and the capacitor set comes with its own supply. The demonstration kit includes a digital multimeter, a voltmeter and an ammeter but needs a low-voltage DC supply from the lab. The starter kit runs on a 9 volt battery, while loose components need a bench supply and a multimeter.
Give each kind of part its own labelled tray or parts box, split further by value, so a student can find a resistor or an LED without emptying a bag. Keep leads straight and boards flat, return the gate modules to their plastic box, and count the small parts back at the end of each lesson so nothing is missing for the next class.
Use the breadboard when the aim is to build, change and fault-find a circuit, because parts push in and come out again for reuse. Use a ready board, such as the diode or logic gate boards, when the aim is a set of measurements, since the components are already mounted and every group gets comparable readings.
No. The starter kit uses a solderless breadboard, the circuit panels and logic gate box connect through 4 mm sockets and leads, and the PN junction and Zener boards come complete with their own meters. Students can build and take apart each circuit within a lesson, which suits classes that are not yet trained to solder.
In forward bias both conduct in much the same way. In reverse bias an ordinary diode blocks current up to a much higher rated voltage, and breaking down usually ruins it. A Zener diode is made to break down at a set reverse voltage and then hold that voltage nearly constant as the current rises. The reverse curve plotted on the Zener board shows this sharp knee.
Once it is in breakdown, the voltage across it stays nearly the same over a broad span of current. Connected in reverse across a load, with a resistor in series to limit the current, it holds the load voltage steady. It needs at least a small reverse current to stay in breakdown, so the resistor must not be too large.
To request a quotation or a catalogue for this range, send the product names, codes and quantities through our contact page or add the items to your enquiry cart.
Last updated: 16 November 2026