This insulin syringe holds 1 ml and is marked in units for U-100 insulin, so a dose is read straight off the barrel in units. A 29G stainless steel needle is fixed to the polypropylene barrel, and a sliding sleeve locks over the needle after use. Each syringe is sterile, single use and sealed in its own pack.
| Parameter | Detail |
|---|---|
| Capacity | 1 ml |
| Scale | U-100 unit markings |
| Needle | Fixed, 29G (standard) |
| Other needle gauges | 27G, 28G, 30G and 31G, each a separate item on request |
| Needle sleeve | Sliding sleeve that locks over the needle |
| Barrel | Polypropylene (PP) |
| Cannula | SUS304 stainless steel |
| Condition | Sterile, single use |
| Packing | Individually sealed pack |
| Product code | SLE/HLI/01 |
| Minimum order | 10 units |
| Dispatch | Usually within 7 to 10 working days |
| Supplied by | ScienceLab (Jain Scientific Equipments Pvt Ltd), Ambala, India |
Reading units in the skills lab. Nursing and pharmacy students draw water from a practice vial and read the volume in units at the edge of the plunger seal nearest the needle. The tutor checks each reading, has the student tap out any air bubble and read again, and then moves on to an injection training arm to rehearse the whole sequence on a model.
Locking the sleeve and disposal. When the practice injection is finished, the student slides the sleeve forward until it locks over the needle. The covered syringe goes into a sharps container in one piece instead of being recapped by hand, and the tray is cleared before the next student starts.
Store room and tray set-up. Keep the sealed packs dry and out of direct sunlight, and issue boxes in the order they arrived. Shelve the insulin syringes apart from general-purpose 1 ml disposable syringes, because one carries a unit scale and the other a millilitre scale, and a mix-up on the tray is easy to make.
U-100 insulin holds 100 units in each millilitre, and this syringe is marked to match, so its 1 ml barrel reads up to 100 units. Use it only with U-100 insulin. Insulin of another strength needs a syringe marked for that strength.
Read the volume at the edge of the plunger seal nearest the needle, not at the flat end you press. Hold the syringe at eye level with the markings facing you, and count the divisions between numbered lines before taking the reading.
A bubble takes up room in the barrel, so the scale shows more units than the liquid really holds. Hold the syringe needle-up, tap the barrel so the bubble rises, push it out gently and check the reading again.
Gauge describes the needle's outer diameter: the higher the number, the thinner the needle. This syringe has a fixed 29G stainless steel needle as standard. Versions with 27G, 28G, 30G or 31G needles are separate items, requested by gauge.
The needle is fixed to the barrel and cannot be removed or changed, so the gauge is chosen when the syringes are requested. There is no hub joint to tighten before use. Afterwards, push the sliding sleeve forward until it locks over the needle.
No. Each syringe is sterile, single use and sealed in its own pack. Open the pack only when the syringe is needed, and never reuse or reprocess it. Once the sleeve is locked over the needle, put the syringe in a sharps container.
Nursing and pharmacy skills labs can source this U-100 insulin syringe from ScienceLab, which is the trading name of Jain Scientific Equipments Pvt Ltd, a company based in Ambala, Haryana. Alongside it ScienceLab supplies leak-proof sharps containers and general-purpose 1 ml syringes, so a skills lab can stock its injection tray from one list. Colleges, technical institutes and dealers in 110 countries buy from ScienceLab. See the ScienceLab company profile.
To request a quotation, send the product name, code and quantity through our contact page or add the item to your enquiry cart.
Last updated: 19 November 2026